ViewSonic Projector Pj1158 User Manual

							
PICTURE Menu
PICTURE	Menu
ItemDescription
BRIGHTNESSUsing the ▲/▼ buttons adjusts the brightness.
Lght	
ó	Dark
CONTRASTUsing the ▲/▼ buttons adjusts the contrast.
Strong	
ó	Weak
GAMMA
Using the ▲/▼ buttons switches the gamma mode.
	#1	DEFAULT
	ó#1	CUSTOM	ó	#2	DEFAULT
	ó	#2	CUSTOM	ó	#3	DEFAULT
	
#5	CUSTOM	
ó 	#5	DEFAULT
	ó	#4	CUSTOM	ó	#4	DEFAULT
	ó	#3	CUSTOM
To adjust CUSTOM
Selectng	a	mode	whose	name	ncludes	CUSTOM and then pressing the ► button 
or
	the 	ENTER 	button 	d splays 	a 	d alog 	to 	a d	
you	n	adjustng	the	mode.
	
Ths	functon	s	useful	when	you	want	to	
change	the	brghtness	of	partcular	tones.
Choose an item using the ◄/► buttons, and 	adjust the level using the ▲/▼ buttons. 
You	can	dsplay	a	test	pattern	for	checkng	the	effect	of	your	adjust
-
ment	by	pressng	the	ENTER	button.	
Each	tme	you	press	the	ENTER	button,	the	pattern	changes	as	
below.
		No	pattern	
ð 	Gray	scale	of	9	steps	
																	Ramp	
 	Gray	scale	of	15	steps
The	 eght	 equalzng	 bars	correspond	 to	eght	 tone	levels	 of	the	 test	
pattern	 except	the	darkest	 n	 the	left	end.	 If	you	 want	 to	adjust	 the	
2nd 	tone 	from 	left 	end 	on 	the 	test 	pattern 	(Gray 	scale 	of 	9 	steps),	
use 	the 	equal z ng 	adjustment 	bar 	“1”. 	The 	darkest 	tone 	at 	the 	left	
end 	of 	the 	test 	pattern 	cannot 	be 	controlled 	w th 	any 	of 	equal z ng	
adjustment	bar.
•	 When	ths	functon	s	performed,	lnes	or	other	dstorton	may	ap-
pear.
From 	the 	PICTURE 	menu, 	 tems 	shown 	 n	the 	table 	below	
can	be	performed.	
Select	an	tem	usng	the
 ▲/▼ 	cursor	buttons	on	the	
projector	or	remote	control,	and	press	the
 ► 	cursor	button	
on	the	projector	or	remote	control,	or	the	ENTER	button	
on	the	remote	control	to	execute	the	tem.	 Then	perform	t	
accordng	to	the	followng	table.
1 
+0 
2 
+0 
3 
+0 
4 
+0 
5 
+0 
6 
+0 
7 
+0 
8 
+0 GAMMA [CUSTOM 1] 
ENTER : 
/07=4)$?
+/#)5672#7&+1
2+%674+0276
126+105%405*#42055
$4+)*60559×%1064#569×
%1.149×6+069×
%1.146/2/+&)#//#&(#7.6
5.%6
06914-#5;/07#%6+8+4+567401((/;//14;5#8
(contnued	on	next	page)
26ViewSonic	 PJ1158 
						

							
ItemDescription
COLOR TEMP
Using the ▲/▼ buttons switches the color temperature mode.
To adjust CUSTOM
Selectng	a	mode	whose	name	ncludes	CUS-TOM and then pressing the ► button or the 
ENTER	button	dsplays	a	dalog	to	ad	you	n	
adjustng	the	OFFSET	and	GAIN	of	the	selected	
mode.
OFFSET	adjustments	change	the	color	ntensty	
on	the	whole	tones	of	the	test	pattern.
GAIN	adjustments	manly	affect	color	ntensty	
on	the	brghter	tones	of	the	test	pattern.
Choose an item using the ◄/► buttons, and adjust the level using the ▲/▼ buttons. 
You	can	dsplay	a	test	pattern	for	checkng	the	effect	of	your	adjust
-
ment	by	pressng	the	ENTER	button.		
Each	tme	you	press	the	ENTER	button,	the	pattern	changes	as	
below.
		No	pattern	
ð 	Gray	scale	of	9	steps	
																	Ramp	
 	Gray	scale	of	15	steps
•	
When	ths	functon	s	performed,	lnes	or	other	dstorton	may	ap-
pear.
COLOR
Using the ▲/▼ buttons adjusts the strength of whole color.
Strong	
ó 	Weak
• This item can be selected only for a video signal, s-video or com-
ponent	vdeo	sgnal.
TINT
Using the ▲/▼ buttons adjusts the tint.
Greensh	
ó 	Reddsh
• This item can be selected only for a video signal, s-video or com-
ponent	vdeo	sgnal.
SHARPNESS
Using the ▲/▼ buttons adjusts the sharpness.
Strong	
ó 	Weak•	There may be some noise and/or the screen may flicker for a mo-
ment	when	an	adjustment	s	made.	 Ths	s	not	a	malfuncton.
PICTURE Menu
PICTURE Menu (continued)
R 
+0 
G 
+0 
B 
+0 COLOR TEMP [CUSTOM-1]
ENTER : OFFSET R 
+0 
G 
+0 
B 
+0 
GAIN 
HIGH DEFAULT � HIGH CUSTOM � MID DEFAULT � MID CUSTOM 
LOW DEFAULT � LOW CUSTOM � Hi-BRIGHT-1 DEFAULT � Hi-BRIGHT-1 CUSTOM  
Hi-BRIGHT-2 DEFAULT � Hi-BRIGHT-2 CUSTOM  
(contnued	on	next	page)
27ViewSonic	 PJ1158 
						

							
PICTURE Menu
ItemDescription
ACTIVE IRIS
Using the ▲/▼ cursor buttons changes the active iris control mode.PRESENTATION		
ó 		
THEATER		ó 		
TURN	OFF															
Feature
PRESENTATION The	actve	rs	dsplays	the	best	presentaton	m-
age	for	both	brght	and	dark	scenes.
THEATER The	actve	rs	dsplays	the	best	theater	mage	for	
both	brght	and	dark	scenes.
TURN	OFF The	actve	rs	s	always	open.
• The screen may flicker when the PRESENTATION or THEATER 
modes	are	selected.	If	ths	occurs	select	 TURN	OFF.
MY MEMORY
Ths	projector	has	4	memores	for	adjustment	data	(for	all	the	tems	
of	the	PICTURE	menu).
Selecting a function using the ▲/▼ buttons and pressing the ► or 
ENTER	button	performs	each	functon.
LOAD1	
ó	LOAD2	ó	LOAD3	ó	LOAD4
SAVE4 	
óSAVE3
	ó	
SAVE2 	ó	
SAVE1
LOAD1, LOAD2, LOAD3, LOAD4
Performng	a	LOAD	functon	loads	the	data	from	the	memory	lnked	
n	the	number	ncluded	n	the	functon’s	name,	and	adjusts	the	pc
-
ture	automatcally	dependng	on	the	data.	
•	 The	LOAD	functons	whose	lnked	memory	has	no	data	are	
skpped.
•	Remember	that	the	current	adjusted	condton	wll	be	lost	by	load
-
ng	data.	If	you	want	to	keep	the	current	adjustment,	please	save	t	
before	performng	a	LOAD	functon.
• There may be some noise and the screen may flicker for a mo-
ment	when	loadng	data.	 Ths	s	not	malfuncton.
•	 The	LOAD	functons	can	be	also	performed	by	the	MY 	MEMORY	
button	 whch	can	be	set	by 	the	 MY	BUTTON	tem 	n	OPTION	 menu.
SAVE1, SAVE2, SAVE3, SAVE4
Performng	a	SAVE	functon	saves	the	current	adjustment	data	nto	
the	memory	lnked	n	the	number	ncluded	n	the	functon’s	name.	
•	Remember	that	the	current	data	beng	stored	of	a	memory	wll	be	
lost	by	savng	a	new	data	nto	the	memory.
PICTURE Menu (continued)
28ViewSonic	 PJ1158 
						

							
IMAGE Menu
IMAGE	Menu
ItemDescription
ASPECT
Using the ▲/▼ buttons switches the mode for aspect ratio. For an RGB signalNORMAL 	ó	4:3	ó	16:9	ó	SMALL									
For an M1-D signal
NORMAL 	ó	4:3	ó	16:9	ó	14:9	ó	SMALL									
For a Video signal, S-video signal or Component video signal
4:3	ó 	16:9	ó	14:9	ó	SMALL					
For no signal4:3 (fixed)
•	 The	NORMAL 	mode	keeps	the	orgnal	aspect	rato	of	the	sgnal.
OVER SCAN
Using the ▲/▼ buttons adjusts the over-scan ratio.
Large	(It	reduces	pcture)	ó Small (It magnifies picture)
•	This item can be selected only for a video, s-video and component signa l.•	When 	th s 	adjustment 	s 	too 	large, 	certa n 	degradat on 	may 	appear	
at	the	frame	area	of	the	pcture.	In	such	a	case,	please	adjust	small.
V POSITION
Using the ▲/▼ buttons adjusts the vertical position. Up	ó 	Down• Over-adjusting the vertical position may cause noise to appear 
on	the	screen.	If	ths	occurs	please	reset	the	vertcal	poston	to	the	
default	settng.	Pressng	the	RESET
	button	when	the	V	POSITION	
s	selected	wll	reset	the	V	POSITION	to	the	default	settng.
• When this function is performed on a video signal, s-video signal, 
or	component	vdeo	sgnal	of	525	(480)	or	625	(576),	the	range	of	
ths	adjustment	depends	on	the	OVER	SCAN	settng.	It	s	not	pos
-
sble	to	adjust	when	the	OVER	SCAN	s	set	to	10.
H POSITION
Using the ▲/▼ buttons adjusts the horizontal position. Left	ó 	Rght
•	Over-adjusting the horizontal position may cause noise to appear 
on	the	screen.	If	ths	occurs	please	reset	the	horzontal	poston	to	the	
default	settng.	Pressng	the	RESET 	button	when	the	H	POSITION	s	
selected	wll	reset	the	H	POSITION	to	the	default	settng.
• When this function is performed on a video signal, s-video signal, 
or	component	vdeo	sgnal	of	525	(480)	or	625	(576),	the	range	of	
ths	adjustment	depends	on	the	OVER	SCAN	settng.	It	s	not	pos
-
sble	to	adjust	when	the	OVER	SCAN	s	set	to	10.
From	the	IMAGE	menu,	tems	shown	n	the	table	below	
can	be	performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on	the	projector	or	remote	control,	or	ENTER	button	on	
the	remote	control	to	execute	the	tem.	 Then	perform	t	
accordng	to	the	followng	table.
/07=4)$?
+/#)
2+%674
5.%6
#761#&,756:%76
#52%61845%#0
*2*#5*5+
						

							
IMAGE Menu
ItemDescription
H PHASE
Using the ▲/▼ buttons adjusts the horizontal phase to eliminate flicker.
Rght	ó	Left
•	 Ths	tem	can	be	selected	only	for	an	RGB	sgnal	or	a	component	
vdeo	sgnal.	(except	525	(480),	625	(576),	SCART 	RGB)
H SIZE
Using the ▲/▼ buttons adjusts the horizontal size.
Large	
ó 	Small
•
	Ths	tem	can	be	selected	only	for	an	RGB	sgnal.
• 	When	ths	adjustment	s	excessve,	the	pcture	may	not	be	ds-
played	correctly.	In	such	a	case,	please	reset	the	adjustment	by	
pressng	the	RESET 	button	on	the	remote	control	durng	ths	opera
-
ton.
AUTO ADJUST EXECUTE Selectng	ths	tem	performs	the	automatc	adjustment	feature.
For an RGB signal
The	vertcal	poston,	the	horzontal	poston,	the	horzontal	phase	
and	the	horzontal	sze	wll	be	automatcally	set	to	default.	
And	the	
aspect	rato	wll	be	automatcally	selected.
	
Make	sure	that	the	applcaton	wndow	s	set	to	ts	maxmum	sze	
pror	to	attemptng	to	use	ths	feature.	 A	dark	pcture	may	stll	be	
ncorrectly	adjusted.	Use	a	brght	pcture	when	adjustng.
For an M1-D signal
The	aspect	rato	wll	be	automatcally	set	to	default.
For a Video signal or S-video signal
The	vdeo	format	best	suted	for	the	respectve	nput	sgnal	wll	be	
selected	automatcally.
Ths	functon	s	avalable	only	when	the	 AUTO	mode	s	selected	to	
the	VIDEO	FORMAT 	tem	n	INPUT	menu.	For	a	component	vdeo	
signal, the signal type is identified automatically independently of 
ths	functon.
For a Video signal, S-video signal or Component video signal
The	vertcal	poston,	horzontal	poston	and	aspect	rato	wll	be	
automatcally	set	to	default.
For a Component video signal
The	horzontal	phase	wll	be	automatcally	set	to	default.
•	The	automatc	adjustment	operaton	requres	about	10	seconds.	
Also	please	note	that	t	may	not	functon	correctly	wth	some	nput.
IMAGE Menu (continued)
30ViewSonic	 PJ1158 
						

							
INPUT Menu
INPUT	Menu
ItemDescription
PROGRESSIVE
Using the ▲/▼ buttons switches the progress mode.
TV	
ó 	FILM	ó	
TURN	OFF
• 	Ths	functon	s	performed	only	for	an	nterlaced	sgnal	of	a	VIDEO	input, an S-VIDEO input or COMPONENT VIDEO input of 525i 
(480),	625	(576)	or	1125	(1080)	sgnal.
• 	When	 TV	or	FILM	s	selected,	the	screen	mage	wll	be	sharp.	FILM adapts to the 2-3 Pull-Down conversion system. But these 
may	cause	a	certan	defect	(for	example,	jagged	lne)	of	the	pcture	
for	a	quck	movng	object.	In	such	a	case,	please	select	 TURN	OFF,	
even	though	the	screen	mage	may	lose	the	sharpness.
VIDEO NR
Using the ▲/▼ buttons switches the noise reduction mode.
HIGH	
ó 	MID	ó	LOW• This function performs only at a VIDEO input, an S-VIDEO or 
COMPONENT 	VIDEO 	nput 	of 	525 (480 ), 	625 (576 ) 	or 	1125 	(1080 )	
sgnal.	
• 	When	ths	functon	s	excessve,	t	may	cause	a	certan	degrada-
ton	of	the	pcture.	
3D-YCS
Using the ▲/▼ buttons switches the 3D-YCS mode.
STILL 	
ó	MOVIE	ó	
TURN	OFF
• 	Ths	functon	performs	only	at	a	VIDEO	nput	of	NTSC,	and	PAL.
• 	MOVIE	s	the	mode	for	mages	wth	a	lot	of	motons	lke	moves,	
and	STILL 	s	the	mode	for	mages	wth	few	motons	or	completely	
stll	ones	lke	sldes.
COLOR SPACE
Using the ▲/▼ buttons switches the mode for color space. 
AUTO	
ó 	RGB	ó	SMPTE240	ó	REC709	ó	REC601						
•
	Ths	tem	can	be	selected	only	for	an	RGB	sgnal	or	a	component	
vdeo	sgnal	(except	525	(480),	625	(576)	and	SCART 	RGB).
•	The	 AUTO	mode	automatcally	selects	the	optmum	mode.	
•	The	 AUTO	operaton	may	not	work	well	at	some	sgnals.	In	such	a	
case,	t	mght	be	good	to	select	a	sutable	mode	except	 AUTO.
From	the	INPUT	menu,	tems	shown	n	the	table	below	can	
be	performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on	the	projector	or	remote	control,	or	ENTER	button	on	
the	remote	control	to	execute	the	tem.	 Then	perform	t	
accordng	to	the	followng	table.
/07=4)$?5.%6
8+&1(14/#6#761
%1.1452#%#761&;%556+..
(4#/.1%-674010
451.76+104)$+0
/&014/#.
%1/21006%1/21006
241)455+8688+&104/+&+/#)2+%674
5672+0276
5%40126+10
#7&+1
06914-#5;/07
(contnued	on	next	page)
31ViewSonic	 PJ1158 
						

							
ItemDescription
COMPONENT
Using the ▲/▼ buttons switches the function of the COMPONENT 
(Y,	Cb/Pb,	Cr/Pr)	port.
COMPONENT 	
ó	SCART
	RGB	
When	the	SCART 	RGB	s	selected,	the	COMPONENT 	(Y,	C
b/Pb,	Cr/Pr)	and	VIDEO	ports	wll	functon	as	a	SCART 	RGB	port.	A	
SCART 	adapter	or	SCART 	cable	s	requred	for	a	SCART 	RGB	
nput	to	the	projector.	For	detals,	contact	your	dealer.
VIDEO FORMAT
Set the video format for the s-video port and video port.
(1)	Use	th
e ◄/► buttons to select the input port.
(2) Using the ▲/▼ buttons switches the mode 
for	vdeo	format.
AUTO		
ó 		NTSC		ó		PAL
		ó		SECAM	
      N-PAL ó M-PAL ó	NTSC4.43	
•
	Ths	tem	s	performed	only	for	a	vdeo	sgnal	from the VIDEO port or the S-VIDEO port. 
• 	The	 AUTO	mode	automatcally	selects	the	optmum	mode.
•	The	 AUTO	operaton	may	not	work	well	for	some	sgnals.	If	the	
pcture	becomes	unstable	(e.g.	an	rregular	pcture,	lack	of	color),	
please	select	the	mode	accordng	to	the	nput	sgnal.
M1-D
Using the ▲/▼ cursor buttons changes the M1-D signal mode.
NORMAL 	
ó	ENHANCED
Feature
NORMALSuitable for DVD signals (16-235)
ENHANCEDSuitable for VGA signals (0-255)
•	
If	the	contrast	of	the	screen	mage	s	too	strong	or	too	weak,	try	finding a more suitable mode.
INPUT Menu
INPUT Menu (continued)
8+&1(14/#658+&1#761065%2#.5%#/065%/2#.02#.
8+&1
(contnued	on	next	page)
VIDEO
CONTROL
AUDIO IN 1AUDIO IN 2
REMOTE CONTROL   S-VIDEOAUDIOOUT  R  L R  L   AUDIO IN 3   AUDIO IN 4
RGB OUTRGB1RGB2M1-DCB/PBYCR/PR
LAN
SCART OUT
V deoGBR
32ViewSonic	 PJ1158 
						

							
ItemDescription
FRAME LOCK
Using the ▲/▼ buttons turns the frame lock function on/off. TURN	ON	
ó 	
TURN	OFF
• 	Ths	tem	can	be	performed	only	on	an	RGB	sgnal	wth	a	vertcal	
frequency	of	50	to	60	Hz.
• 	When	the	 TURN	ON	s	selected,	a	movng	pctures	are	dsplayed	
more	smoothly.
• 	Ths	functon	may	cause	a	certan	degradaton	of	the	pcture.	In	
such	a	case,	please	select	the	 TURN	OFF.
RGB INSet	the	RGB	nput	sgnal	type	for	the	RGB	port.
(1)	Use	th
e ◄/► buttons to select the RGB 
port	to	be	set.
RGB1	
ó 	RGB2
(2) Use the ▲/▼ buttons to select the RGB 
nput	sgnal	type.
SYNC	ON	G	ON	
ó 	SYNC	ON	G	OFF
•	Selectng	the	SYNC	ON	G	ON	turns	the	SYNC	ON	G	mode	on.	
The	SYNC	ON	G	mode	allows	recepton	of	a	sync	on	G	sgnal.
•	 In	 the	 SYNC	 ON	G	mode, 	the	 pcture	 may	be	dstorted	 wth	certan	
nput	sgnals.	In	such	a	case,	remove	the	sgnal	connector	so	that	
no	sgnal	s	receved	and	turn	the	SYNC	ON	G	mode	off,	and	then	
reconnect	the	sgnal.
INPUT Menu
INPUT Menu (continued)
4)$+04)$
5;0%10)1((5;0%10)104)$
(contnued	on	next	page)
33ViewSonic	 PJ1158 
						

							
INPUT Menu
ItemDescription
RESOLUTIONThe	resoluton	for	the	RGB1	and	RGB2	nput	sgnals	can	be	set	on	
ths	projector.
(1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button.
The	RESOLUTION	menu	wll	be	dsplayed.
(2)		In	the	RESOLUTION	menu	select	the	
resolution you wish to display using the ▲/▼ 
buttons.	
Selectng	
AUTO	wll	set	a	resoluton	appropr
-
ate	to	the	nput	sgnal.
(3) Pressing the ► or ENTER button when 
selectng	a	STANDARD	resoluton	wll	auto-
matcally	adjust	the	horzontal	and	vertcal	
postons,	clock	phase	and	horzontal	sze	
and	automatcally	select	an	aspect	rato.	 The	
INFORMATION	dalog	wll	be	dsplayed.
(4) To set a custom resolution use the ▲/▼ 
buttons	to	select	the	CUSTOM	and	the	CUS-TOM RESOLUTION BOX will be displayed. 
Set 	the 	hor zontal 	(HORZ) 	and 	vert cal 	(VERT)	
resolutions using the ▲/▼/◄/► buttons.
Although	not	all	resolutons	are	guaranteed.
(5)	 To	save	the	settng	place	the	cursor	on	the	
right-most digit and press the ► button.
The	horzontal	and	vertcal	postons,	clock	
phase	and	horzontal	sze	wll	be	automat
-
cally	adjusted	and	an	aspect	rato	wll	be	
automatcally	selected.	
After 	the 	INFORMATION 	d alog 	has 	d splayed	
for	about	10	seconds	the	screen	wll	return	
to	the	RESOLUTION	menu	dsplayng	the	
changed	resoluton.
(6)	 To	revert	back	to	the	prevous	resoluton	
wthout	savng	changes	place	the	cursor	on	
the left-most digit and press the ◄ button.
The	screen	wll	then	return	to	the	RESOLUTION	menu	dsplayng	the	prev-
ous	resoluton.
• 	For	some	pctures,	ths	functon	may	not	work	well.
INPUT Menu (continued)
451.76+10
56#0&
%7561/
#761ZZZ
Z
RESOLUTION	MENU
INFORMATIONRGB11280x	768@	60
INFORMATIONRGB1992x	744@	60
451.76+10
56#0&
%7561/
#761ZZZ
Z
%7561/451.76+10
56

*14
						

							
SETUP Menu
SETUP	Menu
ItemDescription
AUTO KEY-
STONE EXECUTE Selectng	ths	tem	performs	the	
Automatc	keystone	dstorton	cor
-
recton.	Projector	automatcally	corrects	vertcal	keystone	dstorton	
due	to	the	(forward/backward)	setup	angle	by	tself.
Ths	functon	wll	be	executed	only	once	when	selected	n	the	Menu.	
When	the	slant	of	the	projector	s	changed,	executes	ths	functon	aga n.
•	The	adjustable	range	of	ths	functon	wll	vary	among	nputs.	For	
some	nput,	ths	functon	may	not	work	well.
•	When	V:INVERT 	or	H&V:INVERT	s	selected	to	the	MIRROR	tem	n	the	
SETUP 	menu,	f	the	projector	screen	s	nclned	or	angled	downward,	ths 	
functon	may	not	work	correctly.
•	When	the	zoom	adjustment	s	set	to	the	 TELE	(telephoto	focus),	ths	
functon	may	be	excessve.	 Ths	functon	should	be	used	when	the	zoom	
adjustment is set to the full WIDE (wide-angle focus) whenever possib le.•	When	the	projector	s	placed	on	the	level	(about	±3°),	ths	functon	may	not	work.•	When	the	projector	s	nclned	to	near	±30	degree	or	over,	ths	
functon	may	not	work	well.
•	When	the	vertcal	lens	shft	s	not	set	fully	upward	(not	set	fully	downward	for	the optional lens type FL-601 only), this function may not work well.• 	When	the	horzontal	lens	shft	s	not	set	to	the	center,	ths	functon	
may	not	work	well.
•	Ths	functon	wll	be	unavalable	when	the	 Transton	Detector	s	on.
KEYSTONE 
Using the ▲/▼ buttons corrects the vertical keystone distortion.
Shrnk	the	top	of	the	mage	
ó 	Shrnk	the	bottom	of	the	mage
•
	The	adjustable	range	of	ths	functon	wll	vary	among	nputs.	For	
some	nput,	ths	functon	may	not	work	well.
•	When	 the	vertcal	 lens	 shft	s	not 	set 	fully	 upward	 (not	set 	fully	 downward	 for	the optional lens type FL-601 only), this function may not work well.•	When	the	horzontal	lens	shft	s	not	set	to	the	center,	ths	functon	may	not	work	well.•	Ths	functon	wll	be	unavalable	when	the	 Transton	Detector	s	on.
KEYSTONE 
Using the ▲/▼ buttons corrects the horizontal keystone distortion.
Shrnk	the	rght	of	the	mage	
ó 	Shrnk	the	left	of	the	mage
•
	The	adjustable	range	of	ths	functon	wll	vary	among	nputs.	For	
some	nput,	ths	functon	may	not	work	well.
•	When	the	horzontal	lens	shft	s	not	set	to	the	center,	ths	functon	may	not	work	well.•	Ths	functon	wll	be	unavalable	when	the	 Transton	Detector	s	on.
From	the	SETUP	menu,	tems	shown	n	the	table	below	
can	be	performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on	the	projector	or	remote	control,	or	the	ENTER	button	
on	the	remote	control	to	execute	the	tem.	 Then	perform	t	
accordng	to	the	followng	table.
/07=4)$?5.%6
-;5610
#761-;5610:%76
9*+524014/#./+4414014/#.
-;5610
+/#)2+%674
5672+0276
5%40126+10
#7&+1
06914-#5;/07
(contnued	on	next	page)
35ViewSonic	 PJ1158