ViewSonic Pjl7211 Projector User Manual

PJL7211ViewSonic6

Part names
Remote control
(1) VIDEO button
(2) COMPUTER button
(3) SEARCH button
(4) STANDBY/ON button
(5) ASPECT button
(6) AUTO button
(7) BLANK button
(8) MAGNIFY - ON button
(9) MAGNIFY - OFF button
(10) MY SOURCE/DOC.CAMERA button
(11) VOLUME - button
(12) FREEZE button
(13) MY BUTTON - 1 button
(14) MY BUTTON - 2 button
(15) KEYSTONE button
(16) POSITION button
(17) MENU button
(18) ▲/▼/◄/► cursor buttons
(19) ENTER button
(20) ESC button
(21) RESET button
(22) Battery cover...

PJL7211ViewSonic7

Setting up
Install the projector according to the environment and manner the projector will be 
used in.
Arrangement
Refer to the illustrations and tables below to determine screen size and projection 
distance.
The values shown in the table are calculated for a full size screen: 1024 x 768
  a  Screen size (diagonal)   b  Projection distance (±10%)
 c1 , c2  Screen height (±10%)
On a horizontal surfaceSuspended from the ceiling
• Keep a space of 30 cm or more between the 
sides of...

PJL7211ViewSonic8

Setting up
►Place the projector in a stable horizontal position. If the 
projector falls or is knocked over, it could cause injury and/or damage to the 
projector. Using a damaged projector could then result in fire and/or electric 
shock.
•  Do not place the projector on an unstable, slanted or vibrational surface such 
as a wobbly or inclined stand.
•   Do not place the projector on its side, front or rear position. 
•   Consult with your dealer before a special installation such as...

PJL7211ViewSonic9

VIDEO OUTRGB OUTCOMPONENT VIDEO OUT      Y      CB/PB     CR/PR

Setting up
Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector. 
Make sure that all the devices are suitable to be connected with this product, and 
prepare the cables required to connect. Please refer to the following illustrations to 
connect them. To input component video signal to the projector, an RCA to D-sub 
cable or adapter is required. For more information,...

PJL7211ViewSonic0

Setting up
• Be sure to read the manuals for devices before connecting them to 
the projector, and make sure that all the devices are suitable to be connected 
with this product. Before connecting to a PC, check the signal level, the signal 
timing, and the resolution.
-  Some signal may need an adapter to input this projector.
-   Some PCs have multiple screen display modes that may include some signals 
which are not supported by this projector. 
-    Although the projector can...

PJL7211ViewSonic

Setting up
Connecting power supply
1.Put the connector of the power cord into the 
AC IN (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet. In a couple of seconds after the 
power supply connection, the POWER 
indicator will light up in steady orange.
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If...

PJL7211ViewSonic

Remote control
Remote control
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control 
starts to malfunction, try to replace the batteries. If you will not use the remote control for 
long period, remove the batteries from the remote control and st ore them in a safe place.
1.Holding the hook part of the battery 
cover, remove it.
2.Align and insert the two AA batteries 
(HITACHI MAXELL, Part No.LR6 or R6P)...

PJL7211ViewSonic3

Remote control
Changing the frequency of  remote control signal
The accessory remote control has the two choices on signal 
frequency, Mode 1:NORMAL and Mode 2:HIGH. If the remote 
control does not function properly, attempt to change the 
signal frequency.
In order to set the Mode, please keep pressing the 
combination of two buttons listed below simultaneously for 
about 3 seconds.
(1) Set to Mode 1:NORMAL... VOLUME - and RESET buttons 
(2) Set to Mode 2:HIGH... MAGNIFY OFF and...

PJL7211ViewSonic4

VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTONPOSITION1 2
ESCENTERMENU
RESET
COMPUTERMY SOURCE/AUTOMAGNIFYPAGE      UPVOLUMEDOWNoONOFF9×FREEZE

Power on/off
1.Make sure that the power cord is firmly and 
correctly connected to the projector and the 
outlet.
Turning on the power
2.Make sure that the POWER indicator is 
steady orange. 
3.Press the STANDBY/ON button on the 
projector or the remote control.
The projection lamp will light up and the POWER  
indicator will...

PJL7211ViewSonic5

Operating
Operating
1.Press COMPUTER button on the remote control to 
select the COMPUTER IN port.
COMPUTER button
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTON
POSITION
1 2
ESC
ENTER
MENU
RESET
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE      UPVOLUME
DOWNo
ON
OFF
9×FREEZE
MY SOURCE /  DOC. CAMERA button1.Press the MY SOURCE / DOC. CAMERA button on 
the remote control. The input signal will be changed 
into the signal you set as MY SOURCE.
●   
This function also can use for...