ViewSonic Pjl7211 Projector User Manual

							
PJL7211ViewSonic6

Part names
Remote control
(1) VIDEO button
(2) COMPUTER button
(3) SEARCH button
(4) STANDBY/ON button
(5) ASPECT button
(6) AUTO button
(7) BLANK button
(8) MAGNIFY - ON button
(9) MAGNIFY - OFF button
(10) MY SOURCE/DOC.CAMERA button
(11) VOLUME - button
(12) FREEZE button
(13) MY BUTTON - 1 button
(14) MY BUTTON - 2 button
(15) KEYSTONE button
(16) POSITION button
(17) MENU button
(18) ▲/▼/◄/► cursor buttons
(19) ENTER button
(20) ESC button
(21) RESET button
(22) Battery cover
Back of  the remote control
* These buttons don’t work.
()
()
(6)(5)
()
(8)(9)
(5)
(3)
(6)
(8)
(0)
(0)
(4)(3)(7)
**()
**(4)
(7)
(9)
()
()
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTON
POSITION
1 2
ESC
ENTER
MENU
RESET
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE      UPVOLUME
DOWNo
ON
OFF
9×FREEZE
►When one of the buttons marked with “*” was pressed, a message “NOT AVAILABLE” appears on the screen.
•    The 
VOLUME - button only works when being pressed with the RESET 
button to change the remote signal frequency. Otherwise, a message “NOT 
AVAILABLE” appears.
NOTICE 
						

							
PJL7211ViewSonic7

Setting up
Install the projector according to the environment and manner the projector will be 
used in.
Arrangement
Refer to the illustrations and tables below to determine screen size and projection 
distance.
The values shown in the table are calculated for a full size screen: 1024 x 768
  a  Screen size (diagonal)   b  Projection distance (±10%)
 c1 , c2  Screen height (±10%)
On a horizontal surfaceSuspended from the ceiling
• Keep a space of 30 cm or more between the 
sides of the projector and other objects such 
as walls.
• For the case of installation in a special state 
such as ceiling mount, the specified mounting 
accessories and service may be required. 
Before installing the projector, consult your 
dealer about your installation.
Setting up
   Screen size(diagonal)
4 : 3 screen16 : 9 screen
  Projection distance Screen heightScreen height Projection distance Screen height Screen height min.max.min.max.
type (inch)mminchminchcminchcminchminchminchcminchcminch
300.8 0.8331.040385830.9361.144354
401.0 1.1451.45450041.2491.5594793
501.3 1.4561.768645351.6 61.9745933
601.5 1.7682.1 87630561.9742.389784
701.8 2.0802.4968935872.2872.704 835
802.0 2.3 92.80 040 082.5993.0994376
902.3 2.6033.13 445392.83.435 06 46
00
2.5 2.9 43.537 7505 03.243.850 84673
0
3.0 3.5 374.265 560303.8504.680 45683
50
3.8 4.4 75.207 97538 54.8875.75 766904
00
5.1 5.8 307.076 5400 506.4507.630 359345
50
6.4 7.3 878.8345 38564 58.0339.6376 94 6 77
3007.6 8.834510.544385076309.537611.5 45353398
babc1c1c2c2 
						

							
PJL7211ViewSonic8

Setting up
►Place the projector in a stable horizontal position. If the 
projector falls or is knocked over, it could cause injury and/or damage to the 
projector. Using a damaged projector could then result in fire and/or electric 
shock.
•  Do not place the projector on an unstable, slanted or vibrational surface such 
as a wobbly or inclined stand.
•   Do not place the projector on its side, front or rear position. 
•   Consult with your dealer before a special installation such as suspending from 
a ceiling or somewhere else.
►Place the projector in a cool place, and ensure that there is sufficient 
ventilation. The high temperature of the projector could cause fire, burns and/or 
malfunction of the projector.
•  Do not stop-up, block or otherwise cover the projector’s vents.
•   Keep a space of 30 cm or more between the sides of the projector and other 
objects such as walls.
• Do not place the projector on metallic thing or anything weak in heat.
•  Do not place the projector on carpet, cushions or bedding.
•   Do not place the projector in direct sunlight or near hot objects such as heaters.
•   Do not place anything near the projector lens or vents, or on top of the 
projector.
•   Do not place anything that may be sucked into or stick to the vents on the 
bottom of the projector. This projector has some intake vents also on the 
bottom.
►Do not place the projector anyplace where it may get wet. Getting the projector 
wet or inserting liquid into the projector could cause fire, electric shock and/or 
malfunction of the projector.
•  Do not place the projector in a bathroom or the outdoors.
•   Do not place anything containing liquid near the projector.
►Use only the mounting accessories the manufacturer specified, and leave 
installing and removing the projector with the mounting accessories to the 
service personnel.
•  Read and keep the user’s manual of the mounting accessories used.
WARNING
►Avoid placing the projector in smoky, humid or dusty place. 
Placing the projector in such places could cause fire, electric shock and/or 
malfunction of the projector.
• Do not place the projector near humidifiers, smoking spaces or a kitchen.
►Position the projector to prevent light from directly hitting the projector’s remote 
sensor.
CAUTION
Arrangement (continued) 
						

							
PJL7211ViewSonic9

VIDEO OUTRGB OUTCOMPONENT VIDEO OUT      Y      CB/PB     CR/PR

Setting up
Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector. 
Make sure that all the devices are suitable to be connected with this product, and 
prepare the cables required to connect. Please refer to the following illustrations to 
connect them. To input component video signal to the projector, an RCA to D-sub 
cable or adapter is required. For more information, please see the description of 
the COMPUTER IN item of the INPUT menu.
VCR/DVD playerPC
►Do not disassemble or modify the projector and accessories.
►Be  careful  not  to  damage  the  cables,  and  do  not  use  damaged  cables.
WARNING
►Turn off all devices and unplug their power cords prior 
to connecting them to projector. Connecting a live device to the projector 
may generate extremely loud noises or other abnormalities that may 
result in malfunction or damage to the device and the projector.
►Use appropriate accessory or designated cables. Ask your dealer about 
non-accessory cables which may be required a specific length or a ferrite 
core by the regulations. For cables with a core only at one end, connect\
 
the end with the core to the projector.
►Make sure that devices are connected to the correct ports. An incorrect 
connection may result in malfunction or damage to the device and the projector.
NOTICE►Use the cables with straight plugs, not L-shaped ones, as the 
input ports of the projector are recessed.
CAUTION 
						

							
PJL7211ViewSonic0

Setting up
• Be sure to read the manuals for devices before connecting them to 
the projector, and make sure that all the devices are suitable to be connected 
with this product. Before connecting to a PC, check the signal level, the signal 
timing, and the resolution.
-  Some signal may need an adapter to input this projector.
-   Some PCs have multiple screen display modes that may include some signals 
which are not supported by this projector. 
-    Although the projector can display signals with resolution up to UXGA  
(1600X1200), the signal will be converted to the projector’s panel resolution 
before being displayed. The best display performance will be achieved if the 
resolutions of the input signal and the projector panel are identical.
• While connecting, make sure that the shape of the cable’s connector fits the 
port to connect with. And be sure to tighten the screws on connectors with 
screws.
• When connecting a laptop PC to the projector, be sure to activate the PC’
s external RGB output. (Set the laptop PC to CRT display or to simultaneous 
LCD and CRT display.) For details on how this is done, please refer to the 
instruction manual of the corresponding laptop PC.
• When the picture resolution is changed on a PC depending on an input, 
automatic adjustment function may take some time and may not be completed. 
In this case, you may not be able to see a check box to select “Yes/No” for the 
new resolution on Windows. Then the resolution will go back to the original. 
It might be recommended to use other CRT or LCD monitors to change the 
resolution.
• In some cases, this projector may not display a proper picture or display 
any picture on screen. For example, automatic adjustment may not function 
correctly with some input signals. An input signal of composite sync or sync on 
G may confuse this projector, so the projector may not display a proper picture.
NOTE
About Plug-and-Play capability
Plug-and-Play is a system composed of a PC, its operating system and 
peripheral equipment (i.e. display devices). This projector is VESA DDC 2B 
compatible. Plug-and-Play can be used by connecting this projector to a PC 
that is VESA DDC (display data channel) compatible. 
• Take advantage of this feature by connecting a computer cable to the 
COMPUTER IN port (DDC 2B compatible). Plug-and-Play may not work 
properly if any other type of connection is attempted.
• Please use the standard drivers in your PC as this projector is a Plug-and-
Play monitor.
Connecting your devices (continued) 
						

							
PJL7211ViewSonic

Setting up
Connecting power supply
1.Put the connector of the power cord into the 
AC IN (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet. In a couple of seconds after the 
power supply connection, the POWER 
indicator will light up in steady orange.
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, consult 
your dealer to get a new one.
• Only plug the power cord into an outlet whose voltage is matched to the power 
cord. The power outlet should be close to the projector and easily accessible. 
Remove the power cord for complete separation.
• Never modify the power cord. 
WARNING
Using the security bar and slot
AC INPower cord
A commercial anti-theft chain or wire up to 
10 mm in diameter can be attached to the 
security bar on the projector.
Also this product has the security slot for 
the Kensington lock. 
For details, see the manual of the security 
tool.
►Do not use the security bar and slot to prevent the projector 
from falling down, since it is not designed for it.
WARNING
►Do not place anti-theft chain or wire near the exhaust vents. It 
may become too hot. 
CAUTION
• The security bar and slot is not comprehensive theft prevention 
measures. It is intended to be used as supplemental theft prevention measure.
NOTE
Security bar
Security slot
Anti-theft chain or wire
Please remember that when the DIRECT ON function 
activated, the connection of the power supply make 
the projector turn on. 
						

							
PJL7211ViewSonic

Remote control
Remote control
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control 
starts to malfunction, try to replace the batteries. If you will not use the remote control for 
long period, remove the batteries from the remote control and st ore them in a safe place.
1.Holding the hook part of the battery 
cover, remove it.
2.Align and insert the two AA batteries 
(HITACHI MAXELL, Part No.LR6 or R6P) 
according to their plus and minus terminals 
as indicated in the remote control.
3.Replace the battery cover in the direction of the arrow and snap it back into place.
►Always handle the batteries with care and use them only as 
directed. Improper use may result in battery explosion, cracking or leakage, 
which could result in fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of dif ferent 
types at the same time. Do not mix a new battery with used one. 
• Make sure the plus and minus terminals are correctly aligned when loading a batter y.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
• Do not place a battery in a fire or water. Keep batteries in a dark, cool and dry place.
• If you observe battery leakage, wipe out the leakage and then replace a battery. 
If the leakage adheres to your body or clothes, rinse well with water immediately .
• Obey the local laws on disposing the battery.
WARNING
213 
						

							
PJL7211ViewSonic3

Remote control
Changing the frequency of  remote control signal
The accessory remote control has the two choices on signal 
frequency, Mode 1:NORMAL and Mode 2:HIGH. If the remote 
control does not function properly, attempt to change the 
signal frequency.
In order to set the Mode, please keep pressing the 
combination of two buttons listed below simultaneously for 
about 3 seconds.
(1) Set to Mode 1:NORMAL... VOLUME - and RESET buttons 
(2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons
Please remember that the REMOTE FREQ. in the SERVICE 
item of the OPTION menu of the projector to be controlled 
should be set to the same mode as the remote control.
()()
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTON
POSITION
1 2
ESCENTER
MENU
RESET
COMPUTERMY SOURCE/AUTOMAGNIFYPAGE      UPVOLUME
DOWNoONOFF9×FREEZE
30º30º
Approx.3 m 
About the remote control signal
The remote control works with the projector’s remote 
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range 
when the sensor is active:
60 degrees (30 degrees to the left and right of the sensor) 
within 3 meters about.
• The remote control signal reflected in the screen or the like may be 
available. If it is difficult to send the signal to the sensor directly , attempt to 
make the signal reflect.
• The remote control uses infrared light to send signals to the projector (Class 1 
LED), so be sure to use the remote control in an area free from obstacles that 
could block the remote control’s signal to the projector.
• The remote control may not work correctly if strong light (such as direct 
sun light) or light from an extremely close range (such as from an inverter 
fluorescent lamp) shines on the remote sensor of the projector. Adjust the 
position of projector avoiding those lights.
NOTE 
						

							
PJL7211ViewSonic4

VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTONPOSITION1 2
ESCENTERMENU
RESET
COMPUTERMY SOURCE/AUTOMAGNIFYPAGE      UPVOLUMEDOWNoONOFF9×FREEZE

Power on/off
1.Make sure that the power cord is firmly and 
correctly connected to the projector and the 
outlet.
Turning on the power
2.Make sure that the POWER indicator is 
steady orange. 
3.Press the STANDBY/ON button on the 
projector or the remote control.
The projection lamp will light up and the POWER  
indicator will begin blinking in green. When the power  
is completely on, the indicator will stop blinking and light in steady green.
Power on/off
To display the picture, select an input signal according to the section “Selecting an 
input signal”.
►A strong light is emitted when the projector’s power is on. Do 
not look into the lens of the projector or look inside of the projector through any 
of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or just 
after use, since it is too hot.
WARNING
1.Press the STANDBY/ON button on the projector or the remote control. The 
message “Power off?” will appear on the screen for about 5 seconds.
Turning off  the power
2.Press the STANDBY/ON button again while the message appears.  
The projector lamp will go off, and the POWER indicator will begin blinking 
in orange. Then the POWER indicator will stop blinking and light in steady 
orange when the lamp cooling is complete.
Do not turn the projector on for about 10 minutes or more after turning it of f. 
Turning the projector on again too soon could shorten the lifetime of some 
consumable parts of the projector.
STANDBY/ON buttonPOWER indicator
• Turn the power on/off in right order. Please power on the projector 
prior to the connected devices. 
• This projector has the function that can make the projector automatically turn 
on/off. Please refer to the DIRECT ON and AUTO OFF items of the OPTION 
menu. 
• Use the shutdown switch only when the projector is not turned off by normal 
procedure.
NOTE 
						

							
PJL7211ViewSonic5

Operating
Operating
1.Press COMPUTER button on the remote control to 
select the COMPUTER IN port.
COMPUTER button
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTON
POSITION
1 2
ESC
ENTER
MENU
RESET
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE      UPVOLUME
DOWNo
ON
OFF
9×FREEZE
MY SOURCE /  DOC. CAMERA button1.Press the MY SOURCE / DOC. CAMERA button on 
the remote control. The input signal will be changed 
into the signal you set as MY SOURCE.
●   
This function also can use for document camera. Select 
the input port that connected the document camera.
1.Press the INPUT button on the projector.  
Each time you press the button, the projector switches its 
input port from the current port as below.
Selecting an input signal
INPUT button
●   While ON is selected for the AUTO SEARCH item in the 
OPTION menu, the projector will keep checking the ports 
alternately till an input signal is detected.
COMPUTER IN ó VIDEO  
1.Press VIDEO button on the remote control to select the 
VIDEO port.
VIDEO button
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTON
POSITION
1 2
ESC
ENTER
MENU
RESET
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE      UPVOLUME
DOWNo
ON
OFF
9×FREEZE