ViewSonic Pjl7211 Projector User Manual

							
PJL7211ViewSonic56

Regarding the indicator lamps (continued)
• When the interior portion has become overheated, for safety 
purposes, the projector is automatically shut down, and the indicator lamps 
may also be turned off. In such a case, disconnect the power cord, and wait at 
least 45 minutes. After the projector has sufficiently cooled down, please make 
confirmation of the attachment state of the lamp and lamp cover, and then turn 
the power on again.
NOTE
POWER 
indicator
LAMP 
indicator
TEMP 
indicatorDescription
Blinking
In Red
or
Lighting
In Red
Turned
off
Lighting
In Red
There is a possibility that the interior portion has become heated.Please turn the power off, and allow the projector to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation of the following items, and then turn the power on again.• Is there blockage of the air passage aperture?• Is the air filter dirty?• Does the peripheral temperature exceed 35°C?If the same indication is displayed after the remedy, please set FAN SPEED of SERVICE item in OPTION menu to HIGH.
Lighting
In Green
Simultaneous
blinking in Red
It is time to clean the air filter.Please immediately turn the power off, and clean or change the air filter referring to the section “Cleaning and replacing the air filter”. After cleaning or changing the air filter, please be sure to reset the filter timer. After the remedy, reset the power to ON.
Lighting
In Green
Alternative
blinking in Red
There is a possibility that the interior portion has become overcooled.Please use the unit within the usage temperature parameters (5°C to 35°C).  After the treatment, reset the power to ON.
Shutting the projector down
Only when the projector can not be turned off by usual 
procedure, please push the shutdown switch using a pin 
or similar, and disconnect the power plug from the power 
outlet. Before turning it on again, wait at least 10 minutes 
to make the projector cool down enough.
Resetting all settings
When it is hard to correct some wrong settings, the FACTORY RESET function 
of SERVICE item in OPTION menu can reset all settings (except LANGUAGE, 
FILTER TIME, LAMP TIME, FILTER MESSAGE and SECURITY settings and etc.) 
to the factory default.
Shutdown switch 
						

							
PJL7211ViewSonic57

Phenomena that may be easy to be mistaken for machine defects
About the phenomenon confused with a machine defect, check and cope with it 
according to the following table.
PhenomenonCases not involving a machine defectReference page
Power does not come on.
The electrical power cord is not plugged in.
Correctly connect the power cord.
The main power source has been interrupted during operation such as by a power outage (blackout), etc.
Please disconnect the power plug from the power outlet, and allow the projector to cool down at least 10 minutes, then turn the power on again.
11, 14
Either there is no lamp and/or lamp cover, or either of these has not been properly fixed.
Please turn the power off and disconnect the power plug from the power outlet, and allow the projector to cool down at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again.
49, 50
No pictures are displayed.
The signal cables are not correctly connected.
Correctly connect the connection cables.9
Signal source does not correctly work.
Correctly set up the signal source device by referring to the manual of the source device.
–
The input changeover settings are mismatched.
Select the input signal, and correct the settings.5
The brightness is adjusted to an extremely low level.
Adjust BRIGHTNESS to a higher level using the menu function.5
The computer cannot detect the projector as a plug and play monitor.
Make sure that the computer can detect a plug and play monitor using another plug and play monitor.0
The BLANK screen is displayed.
Press the BLANK button on the remote control.
0
(Continued on next page) 
						

							
PJL7211ViewSonic58

Phenomena that may be easy to be mistaken for machine defects (continued)
PhenomenonCases not involving a machine defectReference 
page
Video screendisplay freezes.
The FREEZE function is working.
Press the FREEZE button to restore the screen to normal.0
Colors have afaded- outappearance, orColor tone is poor.
Color settings are not correctly adjusted.
Perform picture adjustments by changing the COLOR TEMP, COLOR, TINT and/or COLOR SPACE settings, using the menu functions.
26, 30
COLOR SPACE setting is not suitable.
Change the COLOR SPACE setting to AUTO, RGB, SMPTE240, REC709 or REC601. 
30
Pictures appear 
dark.
The brightness and/or contrast are adjusted to an 
extremely low level.
Adjust BRIGHTNESS and/or CONTRAST settings to a 
higher level using the menu function. 5
The ECO MODE function is working.
Select NORMAL for the ECO MODE item in the SETUP 
menu.
33
The lamp is approaching the end of its product 
lifetime.
Replace the lamp.
49, 50
Pictures appear
blurry.
Either the focus and/or horizontal phase settings are 
not properly adjusted.
Adjust the focus using the focus ring, and/or H PHASE 
using the menu function.
17, 29
The lens is dirty or misty.
Clean the lens referring to the section “Caring for the lens”.53
• Although bright spots or dark spots may appear on the screen, this 
is a unique characteristic of liquid crystal displays, and it does not constitute or 
imply a machine defect.
NOTE 
						

							
PJL7211ViewSonic59

Specifications
Specification
ItemSpecification
Product nameLiquid crystal projector
Liquid Crystal Panel786,432 pixels (1024 horizontal x 768 vertical)
LensZoom lens,  f = 19 ~ 22 mm    (approximately)
Lamp190W UHP
Power supplyAC 100-120V/3.0A, AC220-240V/1.5A
Power consumption250W
Temperature range5 ~ 35°C (Operating)
Size317 (W) x 98 (H) x 288 (D) mm* Not including protruding parts. Please refer to the following figure.
Weight (mass)approx. 3.2kg
Ports
Computer input port
  COMPUTER IN  ..................................D-sub 15 pin mini x1
Video input port
  VIDEO  .....................................................................RCA x1
Optional partsLamp: RLC-054 (DT01026)Air filter: For more information, please consult your dealer. 
						

							
PJL7211ViewSonic60
Specifications (continued)
AA
288
0.7
317
214103
30
95163
58.2
75.568.3
129.7
8.464.5
3.3
109.711.7
[UNIT:mm]
CEILING MOUNT SURFACE
LENS CENTERM4 INSERT NUTA-A5:13 THREADS DETAILS 
						

							
PJL7211ViewSonic6
Customer Support
For technical support or product service, see the table below or contact\
 your reseller.
Note : You will need the product serial number.
Country/RegionWeb SiteT=Telephone
F=FaxE-mail
Australia/New Zealandwww.viewsonic.com.auAUS=1800 880 818
NZ=0800 008 [email protected]
Canadawww.viewsonic.comT (Toll-Free)= 1-866-463-4775T (Toll)= 1-424-233-2533F= [email protected]
Europe/Middle East/Baltic countries/North Africawww.viewsoniceurope.comContact your reseller
Hong Kongwww.hk.viewsonic.comT= 852 3102 [email protected]
Indiawww.in.viewsonic.comT= 1800 11 [email protected]
Koreawww.kr.viewsonic.comT= 080 265 [email protected]
Latin America (Argentina)www.viewsonic.com/la/T= 0800 666 [email protected] 
Latin America (Brazil)www.viewsonic.com/la/T= 0800 891 [email protected]
Latin America (Chile)www.viewsonic.com/la/T= 800 440 [email protected]
Latin America (Columbia)www.viewsonic.com/la/T= 01 800 915 [email protected]
Latin America (Mexico)www.viewsonic.com/la/T= 001 800 514 [email protected]
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Merida, Yucatan. Tel: 01.999.925.19.16
Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico
Latin America (Peru)www.viewsonic.com/la/T= 0800 [email protected]
Macauwww.hk.viewsonic.comT= 853 700 [email protected]
Puerto Rico & Virgin Islandswww.viewsonic.comT= 1-800-688-6688 (English)T= 1-866-379-1304 (Spanish)F= 1-909-468-1202
[email protected]
[email protected]
Singapore/Malaysia/Thailandwww.ap.viewsonic.comT= 65 6461 [email protected]
South Africawww.viewsoniceurope.comwww.viewsoniceurope.com/uk/Support/Calldesk.htm
United Kingdomwww.viewsoniceurope.com/uk/www.viewsoniceurope.com/uk/Support/Calldesk.htm
United Stateswww.viewsonic.comT (Toll-Free)= 1-800-688-6688T (Toll)= 1-424-233-2530F= [email protected] 
						

							
PJL7211ViewSonic6

Limited Warranty
VIEWSONIC® PROJECTOR
What the warranty covers: 
ViewSonic warrants its products to be free from defects in material and w\
orkmanship, under 
normal use, during the warranty period. If a product proves to be defect\
ive in material or 
workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace 
the product with a like product. Replacement product or parts may includ\
e remanufactured or 
refurbished parts or components. 
Limited Three (3) year General Warranty 
Subject to the more limited one (1) year warranty set out below, North and South America: Three (3) 
years warranty for all parts excluding the lamp, three (3) years for l\
abor, and one (1) year for the 
original lamp from the date of the first consumer purchase; Europe excep t Poland: Three (3) years 
warranty for all parts excluding the lamp, three (3) years for labor, and ninety (90) days for the 
original lamp from the date of the first consumer purchase; Poland: Two (2) years warranty for all 
parts excluding the lamp, two (2) years for labor, and ninety (90) days for the original lamp from 
the date of the first consumer purchase. 
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than four (4) hours average 
daily usage, North and South America: One (1) year warranty for all parts excluding the lamp, 
one (1) year for labor, and ninety (90) days for the original lamp from the date of the first 
consumer purchase; Europe: One (1) year warranty for all parts excludi\
ng the lamp, one (1) year 
for labor, and ninety (90) days for the original lamp from the date of the first consumer purchase. 
Other regions or countries: Please check with your local dealer or local  ViewSonic office for the 
warranty information.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’
s installed lamp only.  All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1.  Any product on which the serial number has been defaced, modified o r removed.
2.  Damage, deterioration, failure, or malfunction resulting from:
  a.   Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature, improper 
maintenance, unauthorized product modification, or failure to follow instructions 
supplied with the product.
  b. Operation outside of product specifications.
  c.   Operation of the product for other than the normal intended use or not under normal 
conditions.
  d. Repair or attempted repair by anyone not authorized by ViewSonic.
  e. Any damage of the product due to shipment.
  f. Removal or installation of the product.
  g. Causes external to the product, such as electric power fluctuations or failure.
  h. Use of supplies or parts not meeting ViewSonic’s specifications.
  i. Normal wear and tear.
  j. Any other cause which does not relate to a product defect.
3. 
Removal, installation, and set-up service charges. 
						

							
PJL7211ViewSonic63

How to get service: 
1.    For information about receiving service under warranty, contact ViewSonic Customer 
Support (please refer to “Customer Support” page). You will need to provide your product’s 
serial number.
2.    
To obtain warranted service, you will be required to provide (a) the or\
iginal dated sales slip, (b) your 
name, (c) your address, (d) a description of the problem, and (e) \
the serial number of the product.
3.     Take or ship the product freight prepaid in the original container to an authorized ViewSonic 
service center or ViewSonic. 
4.     For additional information or the name of the nearest ViewSonic service center, contact 
ViewSonic. 
Limitation of implied warranties: 
There are no warranties, express or implied, which extend beyond the des\
cription contained 
herein including the implied warranty of merchantability and fitness for a particular purpose. 
Exclusion of damages: 
ViewSonic’s liability is limited to the cost of repair or replacement of the produ\
ct. ViewSonic 
shall not be liable for: 
1.     Damage to other property caused by any defects in the product, damages based upon 
inconvenience, loss of use of the product, loss of time, loss of profits, loss of business 
opportunity, loss of goodwill, interference with business relationships, or other c\
ommercial 
loss, even if advised of the possibility of such damages. 
2.   Any other damages, whether incidental, consequential or otherwise. 
3.   Any claim against the customer by any other party. 
Effect of state law: 
This warranty gives you specific legal rights, and you may also have other rights which vary from 
state to state. Some states do not allow limitations on implied warranti\
es and/or do not allow the 
exclusion of incidental or consequential damages, so the above limitatio\
ns and exclusions may 
not apply to you. 
Sales outside the U.S.A. and Canada: 
For warranty information and service on ViewSonic products sold outside of the U.S.A. and 
Canada, contact ViewSonic or your local ViewSonic dealer. 
The warranty period for this product in mainland China (Hong Kong, Maca\
o and Taiwan 
Excluded) is subject to the terms and conditions of the Maintenance Gua\
rantee Card.
For users in Europe and Russia, full details of warranty provided can be\
 found in www.
viewsoniceurope.com under Support/Warranty Information.
4.3: Projector Warranty                                                                        PRJ_LW01 Rev. 1h 06-25-07 
						

							
PJL7211ViewSonic64

Mexico Limited Warranty
VIEWSONIC® PROJECTOR
What the warranty covers:ViewSonic warrants its products to be free from defects in material and w\
orkmanship, under normal use, during the warranty period. If a product proves to be defective in \
material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a \
like product. Replacement product or parts may include remanufactured or refurbished p\
arts or components & accessories.
How long the warranty is effective:3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of the first consumer purchase.Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s installed lamp only.All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or remo ved.
2.  Damage, deterioration or malfunction resulting from:
  a.   Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product 
modification, unauthorized attempted repair, or failure to follow instructions supplied with the product.
  b.   Any damage of the product due to shipment.
  c.   Causes external to the product, such as electrical power fluctuations or fa ilure.
  d. Use of supplies or parts not meeting ViewSonic’s specifications.
  e. Normal wear and tear.
  f. Any other cause which does not relate to a product defect.
3.    Any product exhibiting a condition commonly known as “image burn-in”\
 which results when a static 
image is displayed on the product for an extended period of time.
4.    Removal, installation, insurance, and set-up service charges.
How to get service:For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer Support page). You will need to provide your product’s serial number, so please record the product information in the space provided below on your purchase for\
 your future use.  Please retain your receipt of proof of purchase to support your warranty claim.For Your Records
Product Name: ________________________  Model Number: __________________________
Document Number: ____________________  Serial Number: ___________________________
Purchase Date: ________________________  Extended Warranty Purchase? _______________(Y/N)
            If so, what date does warranty expire? _________
1.    To obtain warranty service, you will be required to provide (a) the ori\
ginal dated sales slip, (b) your 
name, (c) your address, (d) a description of the problem, and (e) \
the serial number of the product.
2.    Take or ship the product in the original container packaging to an author\
ized ViewSonic service center.
3.  Round trip transportation costs for in-warranty products will be paid by\
 ViewSonic.
Limitation of implied warranties:There are no warranties, express or implied, which extend beyond the des\
cription contained herein including the implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:ViewSonic’s liability is limited to the cost of repair or replacement of the produ\
ct. ViewSonic shall not be liable for:1.   Damage to other property caused by any defects in the product, damages b\
ased upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity , loss of goodwill, interference with business relationships, or other commercial loss, even\
 if advised of the possibility of such damages.
2.    Any other damages, whether incidental, consequential or otherwise.
3.  Any claim against the customer by any other party.
4.  Repair or attempted repair by anyone not authorized by ViewSonic. 
						

							
PJL7211ViewSonic65

Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,Col. San Fernando Huixquilucan, Estado de MéxicoTel: (55) 3605-1099http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:Distribuciones y Servicios Computacionales SA de CV.Calle Juarez 284 local 2Col. Bugambilias C.P: 83140Tel: 01-66-22-14-9005E-Mail: [email protected]
Villahermosa:Compumantenimietnos Garantizados, S.A. de C.V.AV. GREGORIO MENDEZ #1504COL, FLORIDA C.P. 86040Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09E-Mail: [email protected]
Puebla, Pue. (Matriz):RENTA Y DATOS, S.A. DE C.V. Domicilio:29 SUR 721 COL. LA PAZ72160 PUEBLA, PUE.Tel: 01(52).222.891.55.77 CON 10 LINEASE-Mail: [email protected]
Veracruz, Ver.:CONEXION Y DESARROLLO, S.A DE C.V.  Av. Americas # 419ENTRE PINZÓN Y ALVARADOFracc. Reforma C.P. 91919Tel: 01-22-91-00-31-67E-Mail: [email protected]
ChihuahuaSoluciones Globales en ComputaciónC. Magisterio # 3321 Col. MagisterialChihuahua, Chih.Tel: 4136954E-Mail: [email protected]
Cuernavaca Compusupport de Cuernavaca SA de CVFrancisco Leyva # 178 Col. Miguel HidalgoC.P. 62040, Cuernavaca MorelosTel: 01 777 3180579 / 01 777 3124014E-Mail: [email protected]
Distrito Federal: QPLUS, S.A. de C.V.Av. Coyoacán 931Col. Del Valle 03100, México, D.F.Tel: 01(52)55-50-00-27-35E-Mail : [email protected]
Guadalajara, Jal.:SERVICRECE, S.A. de C.V.Av. Niños Héroes # 2281Col. Arcos Sur, Sector Juárez44170, Guadalajara, JaliscoTel: 01(52)33-36-15-15-43E-Mail: [email protected]
Guerrero AcapulcoGS Computación (Grupo Sesicomp)Progreso #6-A, Colo Centro39300 Acapulco, GuerreroTel: 744-48-32627
Monterrey:Global Product ServicesMar Caribe # 1987, Esquina con Golfo PérsicoFracc. Bernardo Reyes, CP 64280Monterrey N.L. MéxicoTel: 8129-5103E-Mail: [email protected]
MERIDA: ELECTROSERAv Reforma No. 403Gx39 y 41Mérida, Yucatán, México  CP97000Tel: (52) 999-925-1916E-Mail: [email protected]
Oaxaca, Oax.:CENTRO DE DISTRIBUCION YSERVICIO, S.A. de C.V.Murguía # 708 P.A., Col. Centro, 68000, OaxacaTel: 01(52)95-15-15-22-22Fax: 01(52)95-15-13-67-00 E-Mail. [email protected]
Tijuana:STDAv Ferrocarril Sonora #3780 L-C Col 20 de NoviembreTijuana, Mexico
FOR USA SUPPORT: ViewSonic Corporation 381 Brea Canyon Road, Walnut, CA. 91789 USATel: 800-688-6688 (English);  866-323-8056 (Spanish);Fax: 1-800-685-7276E-Mail: http://www.viewsonic.com
4.3: ViewSonic Mexico Limited Warranty                                         PRJ_LW03 Rev. 1A 06-25-07