ViewSonic Pjl6233 Projector User Manual


Chapter 3 Basic Setting and Operation
Network configuration
Click Network on the main menu. The following setting page is displayed. 
The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server) 
and projector name are set up on this menu.
The IP address and Subnet Mask have been configured already in chapter "Installation". 
If you want to change them or configure default gateway or DNS, perform them in this 
page. If you change them, the projector begins restarting and it takes...

ENGLISH
25
E-mail setting
This projector has an E-mail function which can send an alert message 
to users or an administrator if it detects an abnormality on the projector 
or run out of the life span of the lamp. Click E-mail Setting on the main 
menu and follow the below steps.
E-mail setting
Item ................................. Description
SMTP server...........................
Enter server name or IP address of the SMTP server. (up to 60 characters)SMTP server port...............Enter Port number...


Chapter 3 Basic Setting and Operation
2Registering and deleting E-mail addresses
Enter the e-mail address onto "Add e-mail 
address" and click Set button. 
To check the registered addresses, click
Check/Delete sub menu tab. The address-
es are listed as the figure on the right.

 Up to 10 E-mail addresses can be registered.
To delete the registered addresses, check the 
address you want to delete and click Delete
button.
Check / Delete

If the projector sends an alert message due to the...

ENGLISH
27
E-mail setting

"When PJ lamp is off " signifies the lamp goes out without user operation. "When PJ is turned into 
Standby  in proper user operation" signifies that the projector is turned on by using the web browser and 
then it is turned into standby with ON/STANDBY button on the top control or the remote control.

Up to 99,999 hours can be set for use time.
Option5Option selection for sending alert mail
Click Option sub menu tab. Check the con-
dition items under which...


Chapter 3 Basic Setting and Operation

” When PJ lamp replacement time is reached:

Replace it with a new lamp immediately and reset the lamp counter. If the projector is 
used without resetting the lamp counter, the alert mail is sent to users in every power-on 
of the projector. This alert mail will not be sent when unchecking the mail sending condi-
tion "When PJ lamp replacement time is reached".
TITLE: Message from projector
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector...

ENGLISH

SNMP setting
This projector provides a SNMP (Simple Network Management Protocol) 
agent function. The SNMP consists of a manager and agents. The group 
which communicates information each other with SNMP is called 
"Community". There are two access modes in a community, Refer (read only) and Set (read- 
write). This projector allows to use Refer (read only) only. The SNMP message informs the pro-
jector status called "Trap" to an administrator. Click 
SNMP Setting on the main...


Chapter 3 Basic Setting and Operation
Check and delete the trap address
Checking the registered trap address and 
deleting the address.
To delete the address, tick check box in front 
of the IP address and click Delete button.

 Up to 10 trap addresses can be registered.
Trap check/delete
Trap option
Trap option setting
Tick check boxes in front of the condition item 
to send the trap. 

Click Set button if you tick or un-tick the check 
box on a page.

"When PJ lamp is off " signifies the...

ENGLISH

ENGLISH
ViewSonic 3-/3-/

Chapter 4
 Controlling the Projector4
Describes controlling and setting of the projector by using the web 
browser. 


Chapter 4 Controlling the Projector
Power control and status check
Click Power & Status on the main menu. The control page will be dis-
played.
By clicking ON or Standby button on the page, the power of the projector can be con-
trolled. 
Item  Description
PJ status
Power......................... Displays the status of the lamp. (ON, OFF, On starting up, On cooling down)
Status.......................... Displays the status of the projector's power. (Refer to next page.)
Power control...........

ENGLISH

About projector condition
Status Description
Normal............................................................... Projector is operating normally.
Power management in operation........... Power management is operating
Lamp failure................................................... Lamp failure is occurring
Abnormal Temperature......................... The temperature of the projector became too high
Standby after Abnormal Temp......... Projector detects abnormal temp. and sets into standby...