ViewSonic Pjd5223 Projector User Manual

							EN-26
 26 
						

							EN-27
 27
How to operate
1. Press MENU on the projector or Menu on the remote control to open the OSD
menu.
2. When OSD is displayed, use  /  to select any feature in the main menu.
3. After selecting the desired main menu item, press   to enter sub-menu for
feature setting.
4. Use  /  to select the desired item and adjust the settings with  / .
5. Press MENU on the projector or Menu on the remote control, the screen will
return to the main menu.
6. To exit OSD, Press MENU on the projector or Menu on the remote control again.
The OSD menu will close and the projector will automatically save the new
settings.
Picture
Color Mode
There are many factory presets optimized for various types of images.
Brightest : For the brightest environment.
PC : For computer or notebook.Movie : For home theater.
ViewMatch : For accuracy color performance.
User 1 : Memorize user 1 defined settings.User 2 : Memorize user 2 defined settings.
White Board : For white projection screen type.
Black Board : For black projection screen type.Green Board: For green projection screen type.
Reference Mode
Select a picture mode that best suits your need for the image quality and further fine-
tune the image. This function is only available when User 1 or User 2 is selected.
PC : For computer or notebook.
Movie : For home theater.
ViewMatch : For accuracy color performance.White Board : For white projection screen type.
Black Board : For black projection screen type.
Green Board: For green projection screen type.Brightest : For the brightest environment.
Brightness
Brighten or darken the image.
Contrast
Set the difference between light and dark areas.
Color Setting 
						

							EN-28
 28
Adjust the color temperature. At higher temperature the screen looks colder; at lower 
temperature, the screen looks warmer. If you select “User”, then you can change the 
intensity of each of 3 color (Red, Green, Blue) to customize user color temperature.
User Color
User Color provides six sets (RGBCMY) of colors to be adjusted. When you select 
each color, you can independently adjust its range, hue, saturation and gain according 
to your preference.
White Intensity
Increase the brightness of white areas.
Gamma
Effect the represent of dark scenery. With greater gamma value, dark scenery will look 
brighter.
Aspect Ratio
Select how the picture fits on the screen:
Auto : Scales an image proportionally to fit the projectors native resolution in its 
horizontal or vertical width.
4:3 : Scales an image so that it is displayed in the center of the screen with a 
4:3 aspect ratio.
16:9 : Scales an image so that it is displayed in the center of the screen with a 
16:9 aspect ratio.
Keystone
Manually correct distorted images resulting from an angled projection.
3D Sync
On: Enable 3D function.
Off: Disable 3D function.
3D Sync Invert (for TI 3D DLP-LINK only)
On: Invert left and right frame contents.
Off: Default frame contents.
Video/Audio
Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the computer.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
Zoom 
						

							EN-29
 29
Zoom in and out the images.
Video Setting
Allow you to enter the Video Setting menu.
Sharpness: Sharpen or soften the image.
Tint: Shift colors toward red or green.
Color: Adjust the color saturation level.
Audio Setting
Allow you to enter the Audio Setting menu.
Volume: Adjust the projector’s volume level.
Mute: Cut off the sound temporarily.
Setting
Projector Projection
Adjust the picture to match the orientation of the projector: upright or upside-down, in 
front of or behind the screen. Invert or reverse the image accordingly.
Menu Setting
Allow you to enter the Menu Setting menu.
Menu Position: Choose the menu location on the display screen.
Menu Display Time: Duration of OSD menu display countly starts (at idle state by 
second).
OSD Transparency: Select to change the transparency level of the OSD 
background.
Signal Type
Specify the source to the COMPUTER IN 1/COMPUTER IN 2 terminal that you wish to 
project.
Auto : Automatically detect the input signal type from COMPUTER IN 1 and 
COMPUTER IN 2 terminals.
RGB : For VGA signal
YCbCr/YPbPr:For component signal
Blank Screen
Blank the screen temporarily, and select the screen color when this function is active.
Message
Enable or disable the message box at the right bottom of the screen.
Auto Source
Automatically scan through all the input source.
Power Saving
If the input source is not detected and no operation is performed for a specific period of 
time, projector will automatically turn off. 
						

							EN-30
 30
Green Mode
Enable this function when power consumption is under 1W.
Option
Closed Caption
Enable or disable closed captions by selecting CC1 (closed caption1, the most 
common channel), CC2, CC3, CC4, T1, T2 or OFF.
DCR (Dynamic Contrast Ratio)
Enable DCR will further enhance contrast ratio by darkening the black scenes. Disable 
DCR will resume to normal contrast performance. DCR will impact lamp life and 
system noise performance.
Password
Set, change or delete the password. When the password function is added, image 
projection will require to input the preset password when turning on the projector.
Presentation Timer
Remind the presenter to finish the presentation within a certain time frame.
High Altitude
Use this function to allow the fans operates at full speed continuously to achieve 
proper high altitude cooling of the projector.
Lamp Setting
Allow you to enter the Lamp Setting menu.
Lamp Hours: Display the lamp’s elapsed operating time (in hours).
Lamp Hours Reset: Reset the lamp Hour to 0 hours.
ECO Mode: Use this function to dim the projector lamp light output which will 
lower power consumption and increase lamp life. This function will be 
unavailable when the DCR function is on.
My Button
Allow user to define a short cut key on the remote control, and the function item is 
selected in OSD menu.
Te s t  P a t t e r n
Display embedded test pattern.
Factory Default
Restore settings to factory default.
Language
Select the language used by the on-screen menu.
Information
Input Source 
						

							EN-31
 31
Display the current input source.
Resolution
Display current input source resolution.
H. Frequency
Display current image horizontal  frequency.
V. Frequency
Display current image vertical frequency.
Lamp Hours
Display the lamp’s elapsed operating time (in hours). 
						

							EN-32
 32
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt 
or spots will project on the screen and diminish image quality. If any other parts need 
replacing, contact your dealer or qualified service personnel. When cleaning any part 
of the projector, always switch off and unplug the projector first.
Warning
Never open any of the covers on the projector. Dangerous electrical voltages 
inside the projector can cause severe injury. Do not attempt to service this 
product yourself. Refer all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth 
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
Turn off the projector and remove the AC power cord from the power outlet 
before beginning maintenance work.
Make sure the lens is cool before cleaning.Do not use detergents or chemicals other than those noted above. Do not use 
benzene or thinners.
Do not use chemical sprays.Use a soft cloth or lens paper only. 
						

							EN-33
 33
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually 
decreases and the lamp becomes more susceptible to breakage. We recommend 
replacing the lamp if a warning message is displayed. Do not attempt to replace the 
lamp yourself. Contact the qualified service personnel for replacement.
The lamp is extremely hot right after turning off the projector. If you touch the 
lamp, you may scald your finger. When you replace the lamp, wait for at least 
45 minutes for the lamp to cool down.
Do not touch the lamp glass at any time. The lamp may explode due to 
improper handling, including the touching of the lamp glass.
Lamp lifetime may differ from lamp to lamp and according to the environment 
of use. There is no guarantee of the same lifetime for each lamp. Some lamps 
may fail or terminate their lifetime in a shorter period of time than other similar 
lamps.
A lamp may explode as a result of vibration, shock or degradation as a result of 
hours of use as its lifetime draws to an end. Risk of explosion may differ 
according to the environment or conditions in which the projector and lamp are 
being used.
Wear protective gloves and eyeglasses when fixing or detaching the lamp.Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least 
for 5 minutes to turn off the projector after powering on.
Do not operate the lamp in proximity to paper, cloth, or other combustible 
material nor cover it with such materials.
Do not operate the lamp in an atmosphere containing an inflammable 
substance, such as thinner.
Thoroughly ventilate the area or the room when operating the lamp in an 
oxygen atmosphere (in the air). If ozone is inhaled, it could cause headaches, 
nausea, dizziness, and other symptoms.
The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury 
inside the lamp will be exposed. Leave the area immediately if the lamp 
shatters while being operated and ventilate the area for at least 30 minutes in 
order to avoid the inhalation of mercury fumes. Otherwise it could be harmful to 
user’s health. 
						

							EN-34
 34
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the 
module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector.  If the lamp does not turn on after the warm-up period, try 
reinstalling the lamp.
9. Reset the lamp hour. Refer to the “
Option > Lamp Setting” menu.
Dispose the used lamp according to local regulations.Ensure that screws are tightened properly. Screws not tightened fully may 
result in injury or accidents.
Since the lamp is made of glass, do not drop the unit and do not scratch the 
glass.
Do not reuse the old lamp. This could cause the lamp to explode.Be sure to turn off the projector and unplug the AC power cord before 
replacing the lamp.
Do not use the projector with the lamp cover removed. 
						

							EN-35
 35
Specifications
Display system Single 0.55 DLP panel
Resolution XGA (1024 x 768 pixels)
Zoom 1.1X
F/No. 1.97 - 2.17
Focal length 21.95 - 24.18mm
Screen size 30” - 300”
Lamp 180W
Input terminal D-Sub 15-pin x 2, S-Video x 1, Video x 1, Audio signal input (3.5 
mm stereo mini jack) x 1
Output terminal D-Sub 15 pin x 1,  Audio signal output (3.5 mm stereo mini jack) x 
1
Control terminal RS-232 x 1, Mini USB type x1 (supports firmware upgrade and 
remote mouse control)
Speaker 2 watt x 1
Video compatibility NTSC, NTSC 4.43
PAL, PAL-N, PAL M
SECAM, HDTV (480i/p, 576p, 720p, 1080i/p), Composite video
Scanning frequency
Horizontal frequency
Vertical frequency31 - 100 KHz
50 - 120 Hz
Environment Operating:
Temperature: 0°C to 40°C
Humidity: 10%-80%
Storage:
Temperature: -20°C to 60°C
Humidity: 30%-85%
Power requirement AC 100-240 V, 50 - 60 Hz, 2.6A
Power consumption 245 W (Max.)
Dimension (W x D x H) 284.0 x 234.3 x 81.5 mm
Weight 2.6 kg (5.7 lb)
Note: Design and Specifications are subject to change without prior notice.