ViewSonic Pjd5223 Projector User Manual

							IMPORTANT:  Please read this User Guide to obtain important information on instal\
ling and using your product in a safe manner, as well as registering your product for future service.  Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://www.viewsonic.com  in  English,  or  in  specific  languages  using  the  Regional  selection  box  in the upper right corner of our website.  “Antes de operar su equipo le\
a cu idadosamente las instrucciones en este manual”
PJD5223
DLP Projector
User Guide 
						

							i
Compliance Information
FCC StatementThis device complies with part 15 of FCC Rules. Operation is subject to \
the following two conditions: (1) this device may not cause harmful interference, an\
d (2) this device must accept any interference received, including interference that may c\
ause undesired operation.This equipment has been tested and found to comply with the limits for a\
 Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential inst\
allation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interfer\
ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferen\
ce to radio or television reception, which can be determined by turning the equipment o\
ff and on, the user is encouraged to try to correct the interference by one or more of \
the following measures:    • Reorient or relocate the receiving antenna.    • Increase the separation between the equipment and receiver.
    •   Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.    • Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operat\
e the equipment.
For Canada• This Class B digital apparatus complies with Canadian ICES-003.• Cet appareil numérique de la classe B est conforme à la norme NMB-003 du    Canada.
CE Conformity for European CountriesThe device complies with the EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC.
Following information is only for EU-member states:The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE).The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste\
, but use the return and collection systems available.If the batteries, accumulators and button cells included with this equip\
ment, 
display the chemical symbol Hg, Cd, or Pb, then it means that the batter\
y has a heavy metal content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.  
						

							ii
Important Safety Instructions
1.  Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Do not use this unit near water.
6.    Clean with a soft, dry cloth.
7.   
Do not block any ventilation openings. Install the unit in accordance with 
the manufacturer’s instructions.
8.    Do not install near any heat sources such as radiators, heat registers, 
stoves, or other devices (including amplifiers) that produce heat.
9.    Do not defeat the safety purpose of the polarized or grounding-type 
plug. A polarized plug has two blades with one wider than the other. 
A grounding type plug has two blades and a third grounding prong. 
The wide blade and the third prong are provided for your safety. If the 
provided plug does not fit into your outlet, consult an electrician for 
replacement of the obsolete outlet.
10.    Protect the power cord from being walked on or pinched particularly at 
plugs. Convenience receptacles and the point where they exit from the 
unit. Be sure that the power outlet is located near the unit so that it \
is 
easily accessible.
11.    Only use attachments/accessories specified by the manufacturer.
12.    Use only with the cart, stand, tripod, bracket, or table specified 
by the manufacturer, or sold with the unit. When a cart is used, 
use caution when moving the cart/unit combination to avoid 
injury from tipping over.
13.    Unplug this unit when unused for long periods of time.
14.    Refer all servicing to qualified service personnel. Servicing is required 
when the unit has been damaged in any way, such as: if the power-supply 
cord or plug is damaged, if liquid is spilled onto or objects fall into \
the 
unit, if the unit is exposed to rain or moisture, or if the unit does not 
operate normally or has been dropped.  
						

							iii
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive 2002/95/
EC of the European Parliament and the Council on restriction of the use of certain 
hazardous substances in electrical and electronic equipment (RoHS Directive) and is 
deemed to comply with the maximum concentration values issued by the European 
Technical Adaptation Committee (TAC) as shown below: 
Substance
Proposed 
Maximum 
Concentration
Actual Concentration
Lead (Pb)0.1%< 0.1%
Mercury (Hg)0.1%< 0.1%
Cadmium (Cd)0.01%< 0.01%
Hexavalent Chromium (Cr6+)0.1%< 0.1%
Polybrominated biphenyls (PBB)0.1%< 0.1%
Polybrominated diphenyl ethers 
(PBDE)0.1%< 0.1%
Certain components of products as stated above are exempted under the Annex of the 
RoHS Directives as noted below:
Examples of exempted components are:
1.  Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other 
lamps not specifically mentioned in the Annex of RoHS Directive.
2.  Lead in glass of cathode ray tubes, electronic components, fluorescent tubes, and 
electronic ceramic parts (e.g. piezoelectronic devices).
3.  
Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight 
or more lead).
4.  
Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium 
containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by 
weight.  
						

							iv
Copyright Information
Copyright© ViewSonic® Corporation, 2011. All rights reserved.Macintosh and Power Macintosh are registered trademarks of Apple Inc.Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries.ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation.VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are trademarks of VESA.PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages \
resulting from furnishing this material, or the performance or use of this product.In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product informat\
ion as it becomes available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic® Wizard CD-ROM also provides an opportunity for you to print the registration form, which you may mail or fax to ViewSonic.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
PJD5223
ViewSonic DLP Projector
VS13869
PJD5223_UG_ENG Rev. 1A 01-19-11
_______________________________
_______________________________
Product disposal at end of product lifeThe lamp in this product contains mercury which can be dangerous to you \
and the environment. Please use care and dispose of in accordance with local, st\
ate or federal laws.ViewSonic respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more.USA & Canada: http://www.viewsonic.com/company/green/recycle-program/Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx  
						

							EN-1
 1
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, detectable by turning the equipment in question off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna
Increase the distance between the equipment and the receiver
Connect the equipment to an outlet on a different circuit than that which the receiver
is connected to
Or consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to following
two conditions:
1. This device may not cause harmful interference, and 
2. This device must accept any interference that may cause undesired operation. 
						

							EN-2
 2
Safety Instructions
Read all of these instructions before you operate your projector and save for future
reference.
1. Read instructions
All the safety and operating instructions should be read before the appliance is
operated.
2. Notes and warnings
All notes and warnings in the operating instructions should be adhered to.
3. Cleaning
Unplug the projector from the wall socket before cleaning. Use a damp cloth for
cleaning the projector housing. Do not use liquid or aerosol cleaners.
4. Accessories
Do not place this product on an unstable cart, stand, or table. The product may fall,causing serious damage to the product.
Keep the plastic packing materials (from the projector, accessories and optional 
parts) out of the reach of children as these bags may result in death by 
suffocation. Be particularly careful around the small children.
5. Ventilation
The projector is equipped with ventilation holes (intake) and ventilation holes (exhaust).Do not block or place anything near these slots, or internal heat build-up may occur,causing picture degradation or damage to the projector.
6. Power sources
Check that the operating voltage of your unit is identical with the voltage of your localpower supply.
7. Servicing
Do not attempt to service this projector yourself. Refer all servicing to qualified
service personnel.
8. Replacement parts
When replacement parts are required, be sure that the replacement parts are
specified by the manufacture. Unauthorized substitutions may result in fire, electricshock or other hazards.
9. Moisture Condensation
Never operate this projector immediately after moving it from a cold location to 
a warm one. When the projector is exposed to such a change in temperature, 
moisture may condense on the lens and the crucial internal parts. To prevent 
the unit from possible damage, do not use the projector for at least 2 hours 
when there is an extreme or sudden change in temperature. 
						

							EN-3
 3
Notes on the AC Power Cord
AC Power Cord must meet the requirement of countries where you use this projector.
Please confirm your AC plug type with the graphics below and ensure that the proper
AC Power Cord is used. If the supplied AC Power Cord does not match your AC outlet,
please contact your sales dealer. This projector is equipped with a grounding type AC
line plug. Please ensure that your outlet fits the plug. Do not defeat the safety purpose
of this grounding type plug. We highly recommend using a video source device also
equipped with a grounding type AC line plug to prevent signal interference due to
voltage fluctuations.
Avustralya ve Çin 
Toprakları için
Kıta Avrupası  içinA.B.D. ve Kanada için
Birleşik Krallık için
Topraklama
TopraklamaTopraklama Topraklama 
						

							EN-4  
 4
CONTENTS
Introduction ........................................................................ 5
Projector Features ....................................................................................................... 5
Package Contents  ....................................................................................................... 6
Projector Overview  ...................................................................................................... 7
Using the Product  .............................................................. 9
Control Panel  .............................................................................................................. 9
Connection Ports ....................................................................................................... 10
Remote Control  ......................................................................................................... 11
Installing the Batteries  ............................................................................................... 13
Remote Control Operation  ........................................................................................ 14
Connection ....................................................................... 15
Connecting a computer or monitor  ............................................................................ 16
Connecting Video source devices  ............................................................................. 17
Operation .......................................................................... 20
Powering On/Off the Projector  .................................................................................. 20
Adjusting the Projector Height ................................................................................... 21
Adjusting the Projector Zoom and Focus  .................................................................. 21
Adjusting Projection Image Size  ............................................................................... 22
Locking control keys .................................................................................................. 23
Setting the presentation timer  ................................................................................... 24
Menu Operation  ........................................................................................................ 25
Maintenance ..................................................................... 32
Cleaning the Lens  ..................................................................................................... 32
Cleaning the Projector Housing  ................................................................................ 32
Replacing the Lamp  .................................................................................................. 33
Specifications ................................................................... 35
Dimensions ............................................................................................................... 36
Ceiling mount installation  .......................................................................................... 36
Appendix ........................................................................... 37
LED Indicator Messages  ........................................................................................... 37
Compatibility Modes  .................................................................................................. 38
Troubleshooting ........................................................................................................ 40
RS-232 Command and Configuration  ....................................................................... 41
IR Control Code  ........................................................................................................ 44 
						

							EN-5
 5
Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user - friendly 
design to deliver high reliability and ease of use.
The projector offers the following features:
Single chip 0.55 Texas Instruments DLP® technology
XGA (1024 x 768 pixels)
Compatibility with Macintosh® computers
Compatibility with NTSC, PAL, SECAM and HDTV
D-Sub 15-pin terminal for analog video connectivity
User-friendly, multi-language on-screen display
Advanced electronic keystone correction
RS-232 connector for serial control
Less than 1 W power consumption in standby mode
The information in this manual is subject to change without notices.The reproduction, transfer or copy of all or any part of this document is not 
permitted without express written consent.