Vidikron Projector Vision Model 110 User Manual
Here you can view all the pages of manual Vidikron Projector Vision Model 110 User Manual. The Vidikron manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 71
Vidikron Vision Model 110 Owner’s Operating Manual 59 PREL IMINARY 5.1 Lamp Replacement The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or sooner if a noticeable degradation in brightness occurs. When you replace a lamp, you should replace the filters as well. For lamp or filter replacement, please contact your nearest Vidikron authorized service center or Vidikron dealer. Do not attempt to replace the lamp yourself! 1. Turn off the projector and unplug the...
Page 72
Maintenance and Troubleshooting 60 Vidikron Vision Model 110 Owner’s Operating Manual PREL IMINARY 6. Install the new lamp module. 7. Replace the lamp cover and re-tighten all screws. 5.2 Filter Replacement Whenever you replace the lamp – or more often if the projector is installed in an extremely dusty environment – you should also replace the filter located at the right side of the projector. 1. Loosen the two screws holding the filter access panel in place. Then, remove the panel. 2. Pull the...
Page 73
Maintenance and Troubleshooting Vidikron Vision Model 110 Owner’s Operating Manual 61 PREL IMINARY 5.3 Troubleshooting Tips Table 5-1 provides some general guidelines for troubleshooting problems you may encounter with the Vision 110. If the suggested solutions fail to resolve the problem or if you encounter an issue not described here, please contact Vidikron Technical Support. Table 5-1. Troubleshooting Chart SymptomPossible Cause(s)Solution The projector does not turn on after initial...
Page 74
Maintenance and Troubleshooting 62 Vidikron Vision Model 110 Owner’s Operating Manual PREL IMINARY Notes:
Page 75
Vidikron Vision Model 110 Owner’s Operating Manual 63 PREL IMINARY 6.1 RS-232 Connection and Port Configuration To interface the Vision 110 with a home theater automation/control system or a PC running terminal emulation software, connect it to your control system or PC as shown in Figure 3-15. Use a null-modem cable. If you are using a PC to communicate with the Vision 110: 1. Start a terminal session on your PC using a terminal-emulation program, such as HyperTerminal. 2. Configure the PC...
Page 76
Serial Communications 64 Vidikron Vision Model 110 Owner’s Operating Manual PREL IMINARY Table 6-1 lists the serial commands supported by the Vision 110 and the responses it sends back to the control system or PC. Table 6-1. Serial Commands and Responses CommandDescriptionResponse offTurns projector offPowering Down onTurns projector onPowering Up Gennum Init Complete revDisplay system firmware version information: > rev * Vidikron Gennum Scaler Board * * Rev 0.31 (T18) 08 Jun 2007 * File Name:...
Page 77
Serial Communications Vidikron Vision Model 110 Owner’s Operating Manual 65 PREL IMINARY Image Preset Commands SISF 0Loads “ISF Night” image presetISF Night SISF 1Loads “ISF Day” image presetISF Day SISF 2Loads “Custom 1” image presetCustom 1 SISF 3Loads “Custom 2” image presetCustom 2 Menu Navigation Commands The following serial commands are meant to emulate buttons on the remote control or Vision 110 front panel. Each button has its own serial command, so effectively it is as if you were using the...
Page 78
Serial Communications 66 Vidikron Vision Model 110 Owner’s Operating Manual PREL IMINARY Notes:
Page 79
Vidikron Vision Model 110 Owner’s Operating Manual 67 PREL IMINARY 7.1 Vision 110 Specifications Table 7-1 lists the Vision 110 specifications. 7Specifications Table 7-1. Vision 110 Specifications Projector Type:Digital Light Processing (DLP), 3-chip, 16:9 DMD Native Resolution:1920 x 1080 (16:9) Aspect Ratios: 4:3, Letterbox, 16:9, IntelliWide, Cinema, IntelliWide 2.35 Video Standards:NTSC, NTSC 4.43, PAL B/G/H/I/M/N , SECAM DTV Compatibility:480i/576i, 480p, 576p, 1080i 50/60, 720p 50/60,1080p...
Page 80
Specifications 68 Vidikron Vision Model 110 Owner’s Operating Manual PREL IMINARY Brightness and Contrast: Cinema Standards Measurement System (CSMS) Specifications - Brightness: 58.3 foot-Lamberts (fL) - Contrast Ratio: 320:1 These measurements are taken from the projector in a controlled, home theater environment. All measurements are made to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter, Video Essentials test DVD and...