Vidikron Projector Vision Model 110 User Manual

Installation
Vidikron Vision Model 110 Owner’s Operating Manual 29 
PREL
IMINARY
3.7 
Connections to the Vision 
110
Proceed as follows to connect the Vision 110 to your video sources, external controller(s) – if 
present – and AC power.
When connecting your equipment:
 Turn off all equipment before making any connections.
 Use the correct signal cables for each source.
 Ensure that the cables are securely connected. Tighten the thumbscrews on connectors 
that have them.
Connector Panel AccessTo access...

Installation
30 Vidikron Vision Model 110 Owner’s Operating Manual
PREL
IMINARY
Digital (DTV) RGB or Component Video Connections: See Figure 3-11 and Figure 3-12. 
Figure 3-11. Digital (DTV) RGB or Component Video Connections (HD1, HD2)
WIRED REMORED REMOTE
HD2 (BNC)HD1 (RCA)HD1 (RCA)HD2 (BNC)
HD3 (VGA / Y-Pb-Pr)HD3 (VGA / Y-Pb-Pr)
Vert Horiz Red/Pr Blue/Pb Green/Y
Vert Horiz Red/Pr Blue/Pb Green/Y
DTV or Progressive
Component (YPbPr) SourceDTV or Progressive
Component (YPbPr) Source 

Installation
Vidikron Vision Model 110 Owner’s Operating Manual 31 
PREL
IMINARY
Figure 3-12. Digital (DTV) RGB or Component Video Connections (HD3)
HD3 (VGA / Y-Pb-Pr)HD3 (VGA / Y-Pb-Pr)
Green/Y Blue/Pb  Red/Pr  Horiz  Vert
DTV or Progressive
Component (YPbPr) Source 

Installation
32 Vidikron Vision Model 110 Owner’s Operating Manual
PREL
IMINARY
Analog (Computer) RGB Connections: See Figure 3-13. 
Figure 3-13. Analog RGB Connections
HD2 (BNC)HD2 (BNC)
HD3 (VGA / Y-Pb-Pr)HD3 (VGA / Y-Pb-Pr)
Vert Horiz Red/Pr Blue/Pb Green/Y 
Personal
Computer 

Installation
Vidikron Vision Model 110 Owner’s Operating Manual 33 
PREL
IMINARY
S-Video/Composite Video Connections: See Figure 3-14. 
Figure 3-14. S-Video and Composite Video Connections
HD3 (VGA / Y-Pb-Pr)HD3 (VGA / Y-Pb-Pr)
DVD Player, VCR,
Satellite Receiver,
Laser Disc etc. 

Installation
34 Vidikron Vision Model 110 Owner’s Operating Manual
PREL
IMINARY
RS-232 Controller 
Connection
Use a “null-modem” 9-pin RS-232 cable to connect a PC or home theater control/automation 
system (if present) to the RS-232/485 port on the Vision 110; see 
Figure 3-15. 
For more information about using this connection, refer to Serial Communications on 
page 63.
Figure 3-15. RS-232 Control System Connection
➤
WIRED REMOTEWIRED REMOTE
Service port.
Not for user
access
12345
7896
to Automation/...

Installation
Vidikron Vision Model 110 Owner’s Operating Manual 35 
PREL
IMINARY
Connecting 12-volt Trigger 
Outputs to External 
Equipment
If your Vision 110 is equipped with a CineWide with AutoScope system, connect the 
AutoScope lens motor to a 12-volt trigger output on the Vision 110; see 
Figure 3-16.
Similarly connect other 12-volt trigger-activated equipment (such as retractable screens or 
screen masks) to the other trigger outputs. 
For more information on using the 12-volt triggers, refer to...

Installation
36 Vidikron Vision Model 110 Owner’s Operating Manual
PREL
IMINARY
Connecting an External IR 
Receiver to the Vision 110
If infrared signals from the remote control cannot reach the projector due to excessive 
distance or obstructions such as walls or cabinet doors, you can connect an external IR 
receiver to the WIRED REMOTE input on the Vision 110 to extend the range of the remote 
control. See 
Figure 3-17. 
Figure 3-17. External IR Receiver Connection
Connecting to AC PowerProjector:...

Installation
Vidikron Vision Model 110 Owner’s Operating Manual 37 
PREL
IMINARY
3.8 
Turning on the Power
1. Turn on your source components. 
2. If this is an AutoScope-equipped projector, turn on the main power switch at the rear of 
the AutoScope lens motor. The lens motor power switch is located next to the AC input 
(see 
Figure 3-16). 
3. Press the ON button on the remote control – or the SOFT PWR button on the projector 
rear panel – to turn on the system. The vacuum fluorescent display on the...

Installation
38 Vidikron Vision Model 110 Owner’s Operating Manual
PREL
IMINARY
3.10 
Primary Lens Adjustments
To access the motorized lens controls, use the FOCUS, ZOOM and LENS buttons on the Vision 
110 remote control unit (described on page
 12). 
Alternatively, select Display Device from the Service Menu. Select Configure, then Lens from 
the Display Device menu. The Lens menu gives you a great deal of control over the picture 
size, position and focus: 
FocusTo focus the projected image, use the...