Vidikron Projector Vision Model 110 User Manual

Installation
Vidikron Vision Model 110 Owner’s Operating Manual 39 
PREL
IMINARY
3.11 
Installing and Adjusting 
the CineWide Anamorphic 
Lens
If you are installing a CineWide-equipped projector, proceed as follows to install and adjust 
the anamorphic lens. 
Attach Lens Mounting 
Assembly to Lens Motor 
Carriage Plate (CineWide 
with AutoScope) or Base 
Plate (fixed CineWide)
The Vision 110 Anamorphic lens mount kit consists of everything shown in Figure 3-18. Some 
components shipped with your...

Installation
40 Vidikron Vision Model 110 Owner’s Operating Manual
PREL
IMINARY
3. Secure the Anamorphic Lens Holder to the plate using the Hex Bolts/Washers (item #6) 
and Yaw/X
 Adjustment Levers that you removed in Step 1. 
4. Use the Lens Mounting Screws to attach the Lens Adapter Ring (item #1) to the Pitch 
Adjustment Yoke (item #2); see 
Figure 3-19. (Use the round, threaded holes on the yoke.)
5. Use the Height/Y Adjustment T-Screws (item #3), Pitch Adjustment T-Screws (item #4) 
and T-Nuts (item...

Installation
Vidikron Vision Model 110 Owner’s Operating Manual 41 
PREL
IMINARY
Configure Lens Motor TriggerCineWide with AutoScope maintains constant image height independent of the aspect ratio, 
while using the full display resolution of the projector. It accomplishes this by moving the 
anamorphic lens in front of the primary lens when widescreen material is being viewed. 
When the viewer transitions back to 16:9 or 4:3 source material, the anamorphic lens moves 
out of the light path.
To configure...

Installation
42 Vidikron Vision Model 110 Owner’s Operating Manual
PREL
IMINARY
Adjusting the Height (Y): With the white field still on-screen, loosen the 
Height/Y
 Adjustment T-Screws on either side of the lens. Then, slowly move the anamorphic 
lens into place so that there are no shadows on the top or bottom of the screen: 
When the height is properly set, tighten the Height Adjustment T-Screws to secure the lens in 
place.
Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion...

Installation
Vidikron Vision Model 110 Owner’s Operating Manual 43 
PREL
IMINARY
Adjusting the Yaw: Loosen the Yaw/X-Adjustment Levers to allow the lens to pivot freely 
from side to side. Then, angle the lens to even out any left-right pincushion distortion: 
Once the proper lens angle has been set, firmly tighten the Yaw/X-Adjustment Levers to 
secure the lens in place. 
Anamorphic Lens (Top View)
Wrong PositionCorrect Position 

Installation
44 Vidikron Vision Model 110 Owner’s Operating Manual
PREL
IMINARY
Adjusting the Geometry: 
1. Input an anamorphic cross-hatch test pattern to the projector.
2. Unscrew the Anamorphic Lens just enough to allow it to rotate freely.
3. Grasp the lens by the center ring and rotate the lens until the image is properly 
anamorphic: 
4. When the image geometry appears correct, tighten the Anamorphic 
Lens Set Screw (item #10) to secure the lens in place. (When viewed 
from the front, the rear...

Vidikron Vision Model 110 Owner’s Operating Manual 45 
PREL
IMINARY
4.1 
Using the On-Screen 
Menus
To display the Main Menu, press the MENU button on the remote control (Figure 2-4) or 
projector rear panel (Figure 2-2). 
To select a menu item, use the  and  buttons on the remote control or projector rear 
panel to highlight it. Then, to confirm your selection, press ENTER on the remote control (or 
SELECT on the projector rear panel). 
The Vision 110 OSD menus are arranged hierarchically, as shown in...

Operation
46 Vidikron Vision Model 110 Owner’s Operating Manual
PREL
IMINARY
Figure 4-1. Vision 110 OSD Menu Structure
Service
Test VideoHorizontal Ramp 
Vertical Ramp
Color Bars 1
Color Bars 2
Display Device - ConfigureInstallationPicture Orientation:  
Floor Front 
Ceiling Front 
Floor Rear 
Ceiling Rear
LensFocus
Zoom
Shift
Lamp Info
(read-only)Hours in use etc.
DiagnosticWhite, Red, Green, Blue, Yellow, Cyan, 
Magenta
HD FormatHD 1 (RCA)
COMP or RGB HD 2 (BNC)
HD 3 (PC)
Triggers I / II / III (1 / 2 /...

Operation
Vidikron Vision Model 110 Owner’s Operating Manual 47 
PREL
IMINARY
Main MenuThe Main Menu is the starting point for accessing all projector functions. 
(The Calibration and Service menus are hidden and not accessible until you enter a 
passcode.) 
Input SourceFrom the Main Menu, select Input Source to choose a video signal source. 
The active source is indicated by an arrow (>) to its left; in this example, Composite is the 
active source. 
Aspect Ratio To change the aspect ratio (size and...

Operation
48 Vidikron Vision Model 110 Owner’s Operating Manual
PREL
IMINARY
Table 4-1. Aspect Ratio Settings 
Aspect Ratio
Remote 
Control
Key
Description
16:916:9Select 16:9 to view 16:9 DVDs and 
HDTV programs in their native 
aspect ratio. 
 
 
 
 
 
 
4:3 images are stretched 
horizontally to fit a 16:9 screen. 
4:34:3Standard 4:3 scales the input 
signal to fit in the center of the 
16:9 screen. 4:3 is the aspect ratio 
used by computer monitors, 
standard television programming 
and most VHS video...