Toshiba Strata Vie Electronic Key Telephone System User Guide

16CALL FUNCTIONS (continued)HANDSFREE ANSWERBACKTO RECEIVE AN INTERCOM CALL (HANDSFREE)
1) You will hear a single long tone, followed by the
caller’s voice.
l The INT LED will flash at the l-called rate.2) Leave the handset on-hook.
3) To assure a private conversation, depress the 
w
key.
0The INT LED will flash at the l-use rate.4) Speak at a normal voice level in the direction of
the telephone.5) If you depressed the 
m key earlier, depress the
m key when the call is completed.
HANDSFREE...

CALL FUNCTIONS (continued)
INTERCOM CALLS (cont.)
4)Speak when the ring tone ends.5)
Hang up when the call is completed.“See also Automatic Off-Hook Selection (using 
single-
line EKT).Tone signalling can be accomplished by dialing 
0 after
the station number.TO RECEIVE 
AN INTERCOM CALL
1) You will hear a single long tone, followed by the
caller’s voice.
l The INT LED will flash at the l-called rate.2) Lift the handset.
l INT LED will flash at the l-use rate.
3)
Hang up when the call is completed....

F-TOSHIBA
CALL FUNCTIONS (continued)ON-HOOK DIALING (cont.)
4)
Lift the handset to converse.5)
Hang up when the call is completed.
“If busy tone is heard, depress the m key to
disconnect.
OUTSIDE CALLSTO MAKE AN OUTSIDE CALL
1) Lift the handset.
2) Depress any available 
m line key.*
l Listen for dial tone.
l CO line LED will flash at the l-use rate.3) Dial the desired telephone number.
4)
Hang up when the call is completed.
*See also Trunk Queuing andAutomatic Off-Hook Selec-
tion (using single-line...

CALL FUNCTIONS (continued)
SPEAKERPHONE (cont.)TO RECEIVE AN INCOMING CALL
1) You will hear a ringing tone.
2) Leave the handset on-hook.
3) Depress the key of the CO line that is flashing at
the CO incoming rate.
l CO LED will flash at the l-use rate.4) Speak at a normal voice level in the direction of
the telephone.5) Depress the 
m key when the call is completed.
TO MAKE AN INTERCOM CALL (ON-HOOK DIAL-
ING)
1)Leave the handset on-hook.2) Depress the 
m key.
l Listen for intercom dial tone.l INT LED...

p-TOSHIBA.-q
CALL FUNCTIONS (continued)
SPEAKERPHONE (cont.)
0 Push-on/Push-off-The microphone and accompa-
nying LED are OFF during on-hook dialing and
ON at all other times while the speakerphone is
activated. They can be switched OFF/ON or vice
versa by a momentary depression of the 
mkey. They will then remain in the same state until
the 
m key is depressed again or the call is
terminated.
NOTES:
1.To change from Speakerphone to handset:
l Lift handset.
2.To change from handset to Speakerphone:l...

CALL FUNCTIONS (continued)
TRUNK QUEUING
This feature provides a means for station users to be
placed in a waiting queue for a busy outgoing trunk
group, and to be called back when a trunk in the groupis available.TO USE TRUNK QUEUING
1) Lift the handset.
2) Depress the 
m key.
l You will hear intercom dial tone.
l INT LED will flash at the l-use rate.3) Dial the desired trunk group access code (or dial 
61’
and the CO line number) :
4A) If there is an idle trunk, you will be connected and
can dial the...

P-TOSHIBA-q
CALL FUNCTIONS (continued)TRUNK QUEUING (cont.)
*You may cancel the request at anytime prior to the
actual callback by depressing the m key and dialing 0 1,
**lf, after answering a callback, you hear a busy tone, it
means the trunk has already been seized or received
an incoming call. Your request is not cancelled. You
will be called again the next time a trunk becomes idle.
CALL HOLD and TRANSFERCALL HOLDING
TO HOLD A CALL (CO line appears on your station)
While connected to an outside call....

TOSHIBA,CALL HOLD and TRANSFER (cont.)CALL TRANSFER WITH CAMP-ON
This feature allows you to transfer an outside call to
a station that is either idle or busy.
TO TRANSFER A CALL
11) While connected to an outside call, depress the
m key.
l The CO LED changes to conference flash.
l The INT LED will flash at the l-use flash rate.
l Intercom dial tone is heard.
2) Dial the station number to which the call is to be
transferred.
3A) If the called station is idle:
l You will hear a single ring tone.
4A)...

CALL HOLD and TRANSFER (cont.)CALL TRANSFER WITH CAMP-ON (cont.)
3. You may reconnect to a transferred line (anytime
before it is answered) by depressing the appropriate
m key.
TO ANSWER A TRANSFERRED CALL (if your sta-
tion is idle)1) Voice signalling:
a) You will hear a single long tone, followed by
an announcement.l The INT LED will flash at the l-called rate.
b) Acknowledge the announcement.
c) When the transferring station hangs up, you
will hear a ringing tone.
l The CO LED changes to the l-called...

CALL HOLD and TRANSFER (cont.)CALL TRANSFER 
WITH CAMP-ON (cont.)
TO ANSWER A TRANSFERRED CALL (if your sta-
tion is busy)
1) You will hear a 1-sec. warning tone.
l The outside call is camped-on your station.
*The CO LED flashes at the l-hold rate.
2) You have several choices:
a) Depress the appropriate 
m key.
l The existing call will be terminated.
l The new line will be answered and its LED
changes to the l-use flash rate.
bl) Hang up.
l The existing call will be terminated.
l The camped-on line will...