Toshiba Strata Vie Electronic Key Telephone System User Guide

TOSHIBAAUTOMATIC DIALING
AUTOMATIC DIALINGTO CALL AN AUTOMATIC DIALING NUMBER
1) Lift the handset.
2) Depress any available 
(9 line key.
l Listen for dial tone.3) Depress the 
m (or the p ) key.
4) Dial the 2-digit automatic dialing code for the
desired telephone number.
@Your system will automatically dial the number
for you.
5)
Hang up when the call is completed.TO CHAIN DIAL AUTOMATICALLY
Dials two or more automatic dialing numbers during
one call.1) Lift the handset.
2) Depress any available 
m line...

AUTOMATIC DIALING (continued)AUTOMATIC DIALING KEYSPROGRAMMABLE OPTION
After accessing a CO line, automatic dialing for
telephone number storage and use is available by de-
pressing the 
m key instead of a 2-digit access code.
Each 
m key stores one telephone number (up to
16 digits).
TO STORE A TELEPHONE NUMBER*
1)Do not lift the handset.
2) Depress the 
i (or m ) and 1 (or m ) keys,
respectively.
3) Depress the m key you wish to use.
4) Dial the telephone number to be stored (16 digits
maximum).**
5)...

AUTOMATIC DIALING (continued)
REPEAT LAST NUMBER DIALED (cont.)
TO REDIAL LAST NUMBER CALLED
1) Lift the handset.
2) Depress any available CO line key.
l Listen for dial tone.
3) Depress the 
m (or the 1 ) key.
oThe last telephone number you dialed will auto-
matically be redialed.
4)Hang up when the call is completed.
SAVED NUMBER REDIALPROGRAMMABLE OPTION
This feature enables you to store a dialed telephone
number and later redial that number by pressing a
single key.
TO SAVE A TELEPHONE NUMBER
1) Lift...

‘TOSHIBAI,m
1)
2)3)
4)
5)
6)AUTOMATIC DIALING (continued)
TELEPHONE NUMBER STORAGETO STORE A TELEPHONE NUMBER IN SYSTEM
AUTOMATIC DIALING MEMORY*
Automatic dialing telephone numbers can be stored
in the system memory by station 10 only.
1)Do not lift the handset.2) Depress the 
1 and i keys, respectively.
3)
Dial a 2-digit automatic dialing code.l System codes run consecutively from 60 through
99.4) Dial the telephone number to be stored (16 digits
maximum).**
5)
Depress the B key to record the number in...

I-TOSHIBA-r7AUTOMATIC DIALING (continued)
TELEPHONE NUMBER STORAGE (cont.)
*Repeat this procedure to replace the stored telephone
numbers with new ones. Entering an automatic dialing
code that has already been used will replace the current
telephone number with any new one entered.
““It may be necessary to insert a pause after the trunk
access code to allow for dial tone delay. If so, depress
the 
m (or m ) key after entering the PBX
access code.
* AND # TONE DIALINGWhen the 
* or # tones must be output...

CALL FUNCTIONSAUTOMATIC CALLBACK (INTERCOM)
TO USE AUTOMATIC CALLBACK
After reaching a busy or DND station on an intercom
call, you may:
1A) Dial 1 or 1 for Override (see OVERRIDE).
1 B) Depress the 
m *key’;; dial n to set Automatic
Callback.
l Busy tone will stop.l You will hear dial tone for 2 sec. and then busy
tone again.2)
Goon-hook. You may make other calls while waiting
for the called station to become available.3) When the called station becomes idle:
l Your telephone will ring at a fast...

ToSH’=A-CALL FUNCTIONS (continued)
CALL FORWARD
PROGRAMMABLE OPTION
Allowed intercom 
only(all calls will be forwarded).
TO SET A CALL FORWARD
1) Depress the 
m key.
l CFD LED flashes.2) Dial the station number to which calls are to be
forwarded.
3) Depress 
them key.
l CFD LED on steady.l Calls will be forwarded to stored station number.
TO CANCEL A CALL FORWARD
1)Depress the m key.
l CFD LED goes off.
CALL PICK-UP
TOANSWERACALLTHATISPAGINGOR RINGING
1) Lift the handset.
2) 
DepressthemkeyanddialaI...

CALL FUNCTIONS (continued)CONFERENCE CALLSTO CONFERENCE UP TO THREE STATIONS AND
TWO CO LINES, OR FOUR STATIONS AND ONE
CO LINE
Establish a one-CO line call. 
aTO ADD A SECOND CO LINE
1) Depress the 
m key..
l You will hear intercom dial tone.
o The CO LED will flash at the conference rate.
l The INT LED will flash at the l-use rate.2) Select a second CO line and dial the next telephone
number.3) Depress the 
m key after the party answers.*
l CO LEDs will flash at the l-use rate.
l All parties will be...

-ToSH’6A-CALL FUNCTIONS (continued)
CONFERENCE CALLS (cont.)
TO CONFERENCE UP TO FOUR STATIONS ON
ONE INTERCOM LINE
1) Establish a two-station intercom call.
2) Depress 
them key.
l You will hear intercom dial tone.l The INT LED will flash at the conference rate.
3) Dial the third station’s number.
4) Depress 
them key after the party answers.*
l INT LED will flash at the l-use rate.
l All parties will be conferenced.5)
Repeat to add a fourth station.*NOTES:
1.If you receive a busy tone or no answer,...

YTOSHIBACALL FUNCTIONS (continued)
DO NOT DISTURBThis feature allows you to prevent incoming calls
from accessing your station. You can still make out-
going calls.TO USE DO NOT DISTURB MODE
Depress the 
m key.
l DND LED will light steady.
TO RELEASE THE DO NOT DISTURB MODE
Depress the 
m key.
l DND LED goes off.
GROUP LISTENINGThis feature allows all persons present to hear the
distant party’s responses.
With the handset off-hook, depress and hold the
m key.
l SPKR LED lights and the distant party’s...