Toshiba Strata Se, Strata Vie General Description Manual

blank if not allowed. (See Toll Restriction Ac- 
cess Code.) 
6) Hold Recall Time- referring to Table 1, mark 
an X next to the combination of 12, 11 and 
10 that corresponds to the recall time desired 
for each station. If all locations are left blank, 
the timing for that station will default to that 
set in Program 05. 
TABLE 1 
HOLD RECALL TIME CODE 
7) Mark an X next to 07 if automatic off-hook 
selection is to be CO line Group 94 (defaults 
to 9 if Single CO Line Group was selected 
in Program 01)....

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
10) Mark an X next to 01 if the station will be 
allowed to dial p + 7-digit number. This en- 
try overrides any Toll Restriction Class as- 
signed to this station. 
1 1) Mark an X next to 00 if this station will not 
be restricted. This entry overrides all other 
Toll Restriction programming. 
6#XX Program -Station-to-Station Hunting 
Defines the station hunt destination if the 
called station is busy. 
l Enter the station number of the hunt...

l Paging-80 - 89 
l Trunk Group-g, 91 - 98 
l ’ Least Cost Routing-9 
l Door Phone/Monitor Station-66 - 68, 661 
- 673 
Enter the new first digit of the access code 
to be changed as desired. Ensure there are no 
numbering plan conflicts for proper operation. 
Example. 
Entering 0 1 a 3 changes the Door Phone/ 
Monitor Station access codes from 66, 67 
and 68 to 46, 47 and 48, respectively. 
*XX Program-Flexible intercom Numbering 
Changes the system intercom number 
(2-digit) to a new intercom number (1...

PROGRAMMING PROCEDURES 
SECTiON 500-036-300 
JANUARY 1988 
Table 
33 
34 
35 
36 
37 
38 
39 
40 
41 
42 
43 
44 
45 
46 
47 
48 
49 
50 
51 
52 
53 
54 
55 
56 
57 
58 
59 
60 
61 
62 
TABLE LIST (continued) 
Title 
Toll Restriction Class Office Code Entry 
Toll Restriction Area/Office Code Exception Table 
Toll Restriction Class Area/Office Code Exception Table Se- 
lection 
Least Cost Routing Home Area Code 
Least Cost Routing Special Codes 
Least Cost Routing Parameters 
Select Long Distance...

5) Depress the 01 and 03 keys on station 13. 
0 The corresponding LEDs go on. 
6) Depress the m key on station 13. 
l Station 13: All LEDs (except SPKR and 
MIC) begin blinking. 
7) Depress and release the 
SET switch again. 
l SET LED goes off. 
e Station 13: LEDs go off. 
8) Cycle the power switch 
OFF and ON. 
04.04 STRATA Vie: 
NOTE. 
Verify that the battery on the VMAU is con- 
nect& to e::sure ihat data e.itered after sys- 
tem initialization is not lost due to power fail- 
ure. (The SET LED cannot...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
or changed at station 10. When the system 
is initialized, five messages are automatically 
stored in memory. 
60: OUT TO LUNCH 
61. IN A MEETING 
62: CALL 
63: BACK AT 
64: RETURN ON 
04.30 Timer Reminder Messaging Initializa- 
tion 
04.31 To clear Timer Reminder messages, fol- 
low these procedures: 
1) Lock in the 
SET switch. 
l Station 13/17: LED 19 lights steadily. 
2) To clear timer codes, depress the m key 
and dial 11 i. 
0 SPKR LED...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANl!ARY 1988 
TABLE Z-INITIALIZED DATA 
(continued) 
O#l Program 
Door Phone Selection 
None Selected 
02 Program 
System Assignments (Options) 
Tandem Switching = Not selected 
Stations 18/l 9 Amplified Conference = No Am- 
plified Conference 
ACE Warning Tone = No tone 
Display Dialed Number Timeout 
q 15 seconds 
Night Ringing* = Excluded from External Page 
Background Music = Excluded from External 
Page 
External Page = Not included in All Call Page...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 2-INITIALIZED DATA (continued) 
104 Program o+= 
Allowed 
OCC Authorization Code #l AC + 555 = Not allowed 
Blank 
1 XY Program 
105 Program TR 
Class Area Code Entry 
OCC or Equal Access #2 
All Area 
Codes Allowed 
Blank 
106 Program 1 X2 Program 
OCC Authorization Code #2 TR Class Office Code Entry 
Blank All Area Codes Allowed 
108 Program 
2XY Program 
Toll Restriction Override Code #l 
Toll Restriction Area/Office Code Exception...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 2-INITIALIZED DATA (continued) 
2#XY Program 
Area/Office Code Route Table 
Table Chosen = 
8 
STATION ASSIGNMENTS 
3XX Program 
Station CO Line Access 
Access Allowed = All lines, all stations 
3#XX Program 
HOXB, HMDB and HIOB Module Enable 
Blank 
4XX Program 
Station Type Assignment 
20-key Assigned* = All stations 
CO1 Start = All stations Keystrip “A” As- 
signed** = All stations 
*STRATA VJe only 
l *STRA TA Se only 
4#XX Program...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANU’ARY 1988 
05 SYSTEM DATA PRINTOUT 
05.00 System Data Printout Via SMDR 
05.01 If the system is equipped with Station 
Message Detail Recording (SMDR), it is possible 
to obtain a printout of the 
system data and 
speed dialing memory via a printer that is con- 
nected to the SMDR output port (HSMB mo- 
dule). 
05.02 The data should be printed during a low 
traffic period since this procedure interferes 
with normal SMDR output. Any call records 
generated...