Toshiba Strata Se, Strata Vie General Description Manual
Here you can view all the pages of manual Toshiba Strata Se, Strata Vie General Description Manual. The Toshiba manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 41
STRATA Se STRATA Vie FIGURE 17-SCCU/VCCU BATTERY STRAP 07.03 To initialize STRATA Se system data memory, refer to figure 18, temporarily connect a 20-key EKT to station 13, and perform the fol- lowing: STRATA Se STRATA Vlcl FIGURE 18-Se/We lNlTlALlZlNG SWITCHES 1) Place the system power switch in the ON po- sition. 2) Depress the SET switch and allow it to lock. l SET LED goes on. l Station 13: LED 19 goes on. 3) Depress the m key on station 13. l Station 13: SPKR LED goes on. INSTALLATION...
Page 42
INSTALLATION INSTRUCTIONS SECTION 500-036-200 JANUARY 1988 1) Lock in the SET switch. l Station 13/l 7: LED 19 lights steadily. 2) To clear station automatic dialing, depress the m key and dial a p i]. l SPKR LED-flashes continuously. l Depress keys a a a q . l Depress the m key. 3) To clear system automatic dialing, depress the hm key and dial g p 1. l SPKR LED flashes continuously. l Depress keys a a a a. l Depress the m key. 4) Release the SET switch. l The SET LED and LCD 19 on...
Page 43
INSTALLATION INSTRUCTIONS SECTION 500-036-200 JANUARY 1988 08.02 All EKTs share the same dimensions: Height: 3.7” (94 mm) Width: 7.1” (180 mm) Depth: 9.5” (241 mm) 08.03 All EKTs feature modular handset cords and are connected to the system via 4-conduc- tor modular line cords. With the exception of the single-line EKT, all EKTs are also equipped with an additional modular headset connector. In ad- dition, each EKT model may be used at any or all stations. 08.10 HVSU Installation 08.11...
Page 44
INSTAttATlON INSTRUCTIONS SECTION 500-036-200 JANUARY 1988 2) Route the line cord through the notch in the bottom of the EKT. 3) Secure the unit to the desired wall site. (Use dimensions shown in Figure 21 to position the unit.) FIGURE 21-EKT MOUNTING HOLES 4) Route the tail cord through the holes in the base and secure the EKT (Figure 22). FIGURE 22-EKT WIRE ROUTING 5) To reposition the handset handger, insert a piece of wire (such as a paper clip, etc.) into the cutout just above the...
Page 45
FIGURE 24-CARBON HANDSET MOOIFICATION 4) Replace the dynamic handset with the car- bon handset. 08.50 EKT Functional Check 68.51 In order to’ verify basic system func- tions, and confirm the proper functioning of the EKT itself, perform the following test procedures at each station. Begin with the lowest num- bered station, and continue through all stations. 08.52 With handset on-hook: a) Depress the m key. l INT LED: In-use flash. l SPKR LED: on steady. l MIC LED: on steady. l Listen for...
Page 46
INSTALLATION INSTRUCTIONS SECTION 500-036-200 JANUARY 1988 q) Adjust tone signalling volume with upper con- trol on the right side of the EKT. r) Depress the m key. l INT LED: In-use flash. l SPKR & GIG LEDs: on steady. l Listen for intercom dial tone via the EKT speaker. s) Lift handset. . SPKR & MIC LEDs: off. l Speaker off. l Listen for dial tone via handset receiver. t) Call another station and talk into the handset transmitter. 0 Verify that your voice can be heard via the called...
Page 47
PBX Compatible: All of the system’s features, such as Toll Restriction and Automatic Dial- ing, are compatible with PBX operation. Privacy/Non-Privacy: A private system pre- vents other stations from accessing the inter- com or CO lines that are already in use. A non-private system provides conferencing on the CO and intercom lines. Relay Service: In STRATA Vle only, the VMAU PCB is equipped with relays that provide the following signals for external equipment: a) External Page: The relay is...
Page 48
STRATA Se/& GENERAL DESCRIPTION NOVEMBER 1987 cause a tone burst to be sounded via the called station’s speaker. Call Forward: Allows all calls to a station to be routed to another station. The activating sta- tion may be us_ed to originate calls while this feature is active. Call Pickup: Enables a station to pick up calls ringing at other stations or an external page by going off-hook and dialing an access code. Call Pickup (m buttons can be assigned to stations to automatically pick up...
Page 49
09.22 Wall Mounting: Mount the HIOB on a flat surface with the four provided screws. The dimensions are 4.6 x 6.8” (117 x 172 mm). Us- ing the HI06 as a template, mark the four screw locations, create “starter” holes and secure the module. 09.23 Cabling: Each HI06 is connected to a station line via 2-pair 24 AWG wiring (Figure 28). It is connected to the peripheral device via single- or 2-pair (only the tip and ring are used) wiring. The maximum distance between the HKSU and the HIOB is 650’...
Page 50
INSTALLATION INSTRUCTIONS SECTION 500-036-200 JANUARY !988 MF SW1 DP R7 FIGURE 29-HIOB SWITCHES 2) SW3 selects the ringing pattern sent to the peripheral device from the HIOB. Set SW3, if necessary (factory-set to l/3), to l/2 or l/3 (l/2 = 1 second on, 2 seconds off; l/3 = 1 second on, 3 seconds off). 09.27 To Test each HIOB: Connect a stan- dard telephone to the “TEL” input of the HIOB, and perform the following: 1) Using an operational EKT, call the HIOB’s sta- tion number. l Standard...