Toshiba Estudio 230 Manual

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 15
3
[C] Image position adjustment of the primary scannin g direction

(1) While pressing [0] and [5] simultaneously, turn  the power ON.  (Adjustment Mode)
(2) Place a ruler on the original glass with its lea ding edge pushed against the rear side and its side  
along the original scale on the left.
(3) Press [FAX] to make a copy at the mode of A3 (LD ), 100% and standard drawer of the equipment 
(Refer to *). 
*Perform 08-477 and...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 16
[D] Reproduction ratio adjustment of the secondary s canning direction

(1) While pressing [0] and [5] simultaneously, turn  the power ON.  (Adjustment Mode)
(2) Place a ruler on the original glass with its lea ding edge pushed against the original scale on the 
left.
(3) Press [FAX] to make a copy at the mode of A3 (LD ), 100% and standard drawer of the equipment 
(Refer to *). 
*Perform 08-477 and check the value. 
If the value...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 17
3
[E] Image position adjustment of the secondary scann ing direction

(1) While pressing [0] and [5] simultaneously, turn  the power ON.  (Adjustment Mode)
(2) Place a ruler on the original glass with its lea ding edge pushed against the original scale on the 
left.
(3) Press [FAX] to make a copy at the mode of A3 (LD ), 100% and standard drawer of the equipment 
(Refer to *). 
*Perform 08-477 and check the value. 
If the value is...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 18
[F] Top margin 

(1) While pressing [0] and [5] simultaneously, turn  the power ON.  (Adjustment Mode)
(2) Open the platen cover or RADF. 
(3) Press [FAX] to make a copy at the mode of A3/LD,  100%, Text/Photo and standard drawer of the 
equipment (Refer to *). 
*Perform 08-477 and check the value. 
If the value is 0, use the lower drawer. 
If the value is 1, use the upper drawer.
(4) Measure the blank area E at the leading edge...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 19
3
[G] Right margin 

(1) While pressing [0] and [5] simultaneously, turn  the power ON.  (Adjustment Mode)
(2) Open platen cover or RADF. 
(3) Press [FAX] to make a copy at the mode of A3/LD,  100%, Text/Photo and standard drawer of the 
equipment (Refer to *). 
*Perform 08-477 and check the value. 
If the value is 0, use the lower drawer. 
If the value is 1, use the upper drawer.
(4) Measure the blank area F at the right side of...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 20
[H] Bottom margin 

(1) While pressing [0] and [5] simultaneously, turn  the power ON.  (Adjustment Mode)
(2) Open platen cover or RADF. 
(3) Press the [FAX] to make a copy at the mode of A3 /LD, 100%, Text/Photo and standard drawer of 
the equipment (Refer to *). 
*Perform 08-477 and check the value. 
If the value is 0, use the lower drawer. 
If the value is 1, use the upper drawer.
(4) Measure the blank area G at the trailing...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 21
3
3.3 Image Quality Adjustment (Copying Function) 
3.3.1 Density adjustment
The center density and the density variation contro lled by density adjustment keys can be adjusted as 
follows. < Adjustment Mode (05) >
* The values in “( )” are the adjustment codes of th e Custom Mode.
Make a test copy and compare the image obtained wit h the current settings; if necessary, make adjust-
ment using the following procedure. 

(1) While...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 22
3.3.2 Gamma slope adjustment
Gamma slope is adjustable with the following codes.
< Adjustment Mode (05) >
* The values in “( )” are the adjustment codes of th e Custom Mode.
 
Procedure is same as that of   P.3-21 3.3.1 Density adjustment.
Original mode
Item to be adjusted Remarks
Text/Photo Photo Text
593
(943) 594
(945) 595
(944) Gamma slope adjustment Ones place:
0: equivalent to the set value 5 
1 to 9: Select the gamma slope...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 23
3
3.3.3 Sharpness adjustment
If you want to make copy images look softer or shar per, perform the following adjustment.
< Adjustment Mode (05) >
* The values in “( )” are the adjustment codes of th e Custom Mode.
Make a test copy and compare the image obtained wit h the current settings; if necessary, make adjust-
ment using the following procedure. 
 
Procedure is same as that of   P.3-21 3.3.1 Density adjustment.
Original mode...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 24
3.3.4 Setting range correction
The values of the background peak / text peak in th
e range correction can be switched to “varied” or 
“fixed” in the following codes. 
If they are fixed, the range correction is performe d with standard values.
The values of the background peak affect the reprod uction of the background density and the values of 
the text peak affect that of the text density.
< Adjustment Mode (05) >
* The values in...