Toshiba Estudio 230 Manual

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 255
2
2.2.11 Classification List of Adjustment Mode (05) /  Setting Mode (08)
 (e-STUDIO202L/232/282)
Classification e-STUDIO202L/232/282
Adjustment Mode (05) Setting Mode (08)
User interface [Date/Time] 200, 638, 640
[Timer] 204, 205, 206, 260 
[Screen] 207, 602, 1132 
[File] 209, 219, 264, 288 
[Language] 220, 221
[Administrator] 263 
[Scanning] 265, 266, 273, 274 
[Filing] 267, 270, 950, 976, 980, 981,...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 256
Image [Margin] 430, 431, 432, 433, 434-0 to 1, 435, 
436, 437, 438 
[Image density] 501, 503, 504, 505, 506, 507, 
508, 509, 510, 512, 514, 515, 710, 714, 715,  
719, 720, 724, 725, 729, 845, 846, 847, 850,  
851, 852, 855, 856, 857, 860, 861, 862, 931, 
932, 933, 934, 935, 936, 937, 938, 939, 940,  
941, 942 
[Range correction] 532, 533, 534, 570, 571, 
572, 693, 694, 695, 820, 821, 822, 825, 826,...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 257
2
RADF [Aligning amount] 354, 355 [Transporting] 357, 358, 365, 366 [Switchback] 462
Finisher [Folding / Binding position] 468-0 to 2 [Tra y reset] 648
[Cascade] 652, 653 
[Interruption of stapling operation (no staple) ]  
704-0 to 1
Network [NIC] 1002, 1003, 1119
[IP address] 1006, 1007, 1008, 1009, 1010 
[IPX] 1011, 1099 
[Frame type] 1012 
[NCP] 1013
[AppleTalk] 1014, 1015, 1854, 1855, 1936 
[LDAP]...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 258
Network
[MAC address] 1141 
[ACC] 1431 
[Disable print save] 1435 
[Disable fax save] 1436 
[IP Confilct] 1440 
[SNTP] 1441, 1442, 1444, 1445, 1446 
[Device authentication] 1470, 1920, 1952,  
1953, 1958, 1959, 1942, 1944 
[IP Filter] 1720, 1721, 1722, 1723, 1724, 1725, 
1726, 1727, 1728, 1729, 1730, 1731, 1732,  
1733, 1734, 1735, 1736, 1737, 1738, 1739 
[SSL setting] 1740, 1741, 1742, 1743, 1744,...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 259
2
Maintenance [PM counter] 251, 252
[Telephone] 250 
[Error history] 253
[FSMS] 258, 999 
[Service notification] 702, 703, 707, 715, 716,  
717, 718, 719, 720, 721, 723, 767, 768, 769, 
770, 771, 772, 773, 774, 775, 776, 777, 778,  
779, 780, 781, 782, 783, 784, 785, 786, 787,  
788, 789, 790, 796
[HTTP] 726, 727, 728, 729, 730, 731 
[Supply order] 732, 733, 734, 738, 739, 740,  
741, 742, 743, 744, 745,...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 260 

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 1
3
3. ADJUSTMENT 
3.1 Adjustment of Auto-Toner Sensor
When the developer material is replaced, adjust the  auto-toner sensor in the following procedure.
 (Adjustment Mode (05-200)) (1) Install the process unit into the equipment.
Note: Note:  Do not install the toner cartridge.
(2) While pressing [0] and [5] simultaneously, turn  the power ON.
The following message will be displayed.
 Fig.3-1
(3) Key in code [200] and press the...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 2
(4) After about two minutes, the value B automatical ly starts changing.
 Fig.3-3
(5) After a short time, the value B becomes stable and the display changes as follows.
 Fig.3-4
(6) Check if the value B is within the range of 235 to 245 (the output voltage range of the auto-toner 
sensor is 2.35 V to 2.45 V).
(7) If the value B is not within the range of 235 to  245, press the Up or Down button to adjust the 
value manually.
Note:...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 3
3
3.2 Image Dimensional Adjustment 
3.2.1 General description
There are several adjustment items in the image dim ensional adjustment, as listed below. When adjust-
ing these items, the following adjustment order sho uld strictly be observed.
Item to be adjusted Code in mode 05
1 Paper alignment at the registration roller 448, 449 , 450, 452, 455, 457, 
458, 460, 461, 462, 463, 469,  470, 471, 472, 473, 474
2 Printer related...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 4
[Procedure to key in adjustment values] 
In accordance with the procedure described below, m ake adjustment of each adjustment item so that 
the measured values obtained from test copies satis fy the specification. By pressing the [FAX] button, 
immediately after starting the Adjustment Mode (05) , single-sided test copying can be performed (nor-
mal copy mode).
 Fig.3-6
0
1
5
POWER
ENTER
INTERRUPT
Digital keys
START : Enter...