Toshiba Estudio 230 Manual

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 5
3
3.2.2 Paper alignment at the registration roller
The aligning amount is adjusted by using the follow ing codes in Adjustment Mode (05).
Sub-code (*1) 0: Long size 1: Middle size 2: Short size 
(*2) 0: Long size 1: Middle size 2: Short size 3: P ost card
(*3) 0: Long size of OHP film 1: Middle size of OHP  film 2: Short size of OHP film
Notes: 
1. Long size: 330 mm or longer (13.0 inches or longe r)
Middle size: 220-239 mm...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 6
(3) Perform the same procedure for all paper sources.
Note: Note:  When paper thinner than specified is used, paper ja ms may occur frequently at the registration 
section. In this case, it is advisable to change (or  reduce) the aligning amount.
However, if the aligning amount is reduced too much , this may cause the shift of leading edge 
position. So, when adjusting the aligning amount, t ry to choose the appropriate amount...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 7
3
3.2.3 Printer related adjustment
[A] Reproduction ratio of primary scanning direction  (Fine adjustment of polygonal motor rotation 
speed (Printer))

(1) While pressing [0] and [5] simultaneously, turn  the power ON.  (Adjustment Mode)
(2) Press [1]   [FAX]. (A grid pattern with 10 mm squares is print ed out. Use A3/LD from standard 
drawer of the equipment (Refer to *). 
*Perform 08-477 and check the value. 
If the value is 0,...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 8
(6) After the adjustment for the code 411 is complet ed, apply the same adjustment value for the 
code 410. 
(Adjustment Mode)   (Key in the code [410])   [START]
  (Key in the same value in the step 5 above)
  Press [ENTER] or [INTERRUPT] (Stored in memory).
Note: Note: 
Make sure the first line of the grid pattern is pri nted out since the line is occasionally vanished.
[C] Reproduction ratio of secondary scanning directi on...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 9
3
[D] Secondary scanning data laser writing start posi tion
This adjustment has to be performed for each paper  source. (If there is no paper source, skip this step.)
The following table shows the order of the paper so urce to be adjusted, code, paper size and accept-
able values. 
Perform 08-477 and check the value.
When the value is 0. 
When the value is 1. 

(1) While pressing [0] and [5] simultaneously, turn  the power ON....

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 10
[E] Primary scanning data laser writing start positi on at duplexing
Note: Note: 
Make sure the first line of the grid pattern is pri nted out since the line is occasionally vanished.
[E-1] Adjustment for long-sized paper 

(1) While pressing [0] and [5] simultaneously, turn  the power ON.  (Adjustment Mode)
(2) Press [3]   [FAX]. (A grid pattern with 10 mm squares is print ed out. Use A3/LD from standard 
drawer of the equipment...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 11
3
 Fig.3-8 Grid pattern
 
Perform 08-477 and check the value. 
When the value is 0. 
[0] [5] [Power ON]   [1] ([3](05-445, 498) for duplexing)   [FAX]
A: 05-401 (Lower drawer, A3/LD)   200±0.5 mm (0.125 mm/step)
B: 05-411 (Lower drawer, A3/LD)  52±0.5 mm (0.05 mm/step)
  Key in the same value for 05-410.
C: 05-421 (Lower drawer, A3/LD)  200±0.5 mm (0.125 mm/step)
D:  05-441 (Lower drawer, A3/LD), 440 (Upper drawer,  A4/LT), 444...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 12
Remark:  When the adjustment (05-421) is performed, the same  adjustment for FAX (05-422) is automati-
cally and consecutively performed.
3.2.4 Scanner related adjustment
[A] Image distortion
 Fig.3-9
When the value is 1. 
[0] [5] [Power ON]   [1] ([3](05-445, 498) for duplexing)   [FAX]
A: 05-401 (Upper drawer, A3/LD)  200±0.5 mm (0.125 mm/step)
B: 05-411 (Upper drawer, A3/LD)  52±0.5 mm (0.05 mm/step)
  Key in the same value for...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 13
3

(1) While pressing [0] and [5] simultaneously,  turn the power ON.
(2) Press [FAX] to make a copy of any image on  a sheet of A3/LD paper.
(3) Key in [308] and press the [START] button to  move the carriage to the adjustment position.
(4) Make an adjustment in the order of step 1  and 2. 
 Step 1- In case of A:Tighten the mirror-3 adjustment screw  
(CW).
- In case of B: Loosen the mirror-3 adjustment screw 
(CCW).
 Step 2
-...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 14
[B] Reproduction ratio adjustment of the primary sca nning direction

(1) While pressing [0] and [5] simultaneously, turn  the power ON  (Adjustment Mode)
(2) Place a ruler on the original glass (along the d irection from the rear to the front of the equipment).
(3) Press [FAX] to make a copy at the mode of A3 (LD ), 100% and standard drawer of the equipment 
(Refer to *). 
*Perform 08-477 and check the value. 
If the value is 0,...