Toshiba Estudio 230 Manual

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 175
2
412 Fuser Fuser roller temperature  during printing 
(Center thermistor/Thick  
paper 3) ALL 9
 M 0: 140°C 1: 145°C
2: 150°C 3: 155°C 
4: 160°C 5: 165°C 
6: 170°C 7: 175°C
8: 180°C 9: 185°C 
10: 190°C 
11: 195°C
12: 200°C 
13: 205°C 
14: 210°C 1
413 Fuser Fuser roller temperature  during printing 
(Center thermistor/Thick  
paper 1) ALL 8
 M 0: 140°C 1: 145°C
2: 150°C 3: 155°C 
4: 160°C 5: 165°C 
6:...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 176
424-0 Fuser Temperature 
drop switching  
time setting in  
ready status 
(Center ther- 
mistor)The first  
drop
ALL 15
 M This code is valid only 
when “20” is set to 08- 
886. 
Setting value x 1 min.: 
from 2 to 60 min.  later 4
424-1 The sec- ond dropALL 15
 M 4
424-2 The third  dropALL 15
 M 4
424-3 The fourth  dropALL 15
 M 4
425-0 Fuser Temperature  drop switching 
time setting in 
ready status...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 177
2
440 Fuser Pre-running time for first  printing 
(Plain paper) ALL 0
 M 0: Invalid 1: 1 sec.
2: 2 sec. 3: 3 sec.
4: 4 sec. 5: 5 sec. 
6: 6 sec. 7: 7 sec.
8: 8 sec. 9: 9 sec. 
10: 10 sec. 
11: 12 sec.
12: 14 sec. 
13: 16 sec. 
14: 18 sec. 
15: 20 sec. 1
441 Fuser Pre-running time for first  printing 
(Thick paper 1) ALL 0
 M 0: Invalid 1: 1 sec.
2: 2 sec. 3: 3 sec.
4: 4 sec. 5: 5 sec.
6: 6 sec. 7: 7 sec....

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 178
452 Fuser Fuser roller temperature 
during printing 
(Side thermistor/Thick  
paper 2) ALL 8
 M 0: 140°C 1: 145°C
2: 150°C 3: 155°C 
4: 160°C 5: 165°C 
6: 170°C 7: 175°C
8: 180°C 9: 185°C 
10: 190°C 
11: 195°C
12: 200°C 
13: 205°C 
14: 210°C 1
453 Fuser Fuser roller temperature  during printing 
(Side thermistor/OHP film) ALL 8
 M 0: 140°C 1: 145°C
2: 150°C 3: 155°C
4: 160°C 5: 165°C 
6: 170°C 7: 175°C...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 179
2
462 RADF Setting for switchback  operation in mixed-size  
copying using RADF ALL 0
 M This setting is whether 
the original length is 
detected or not by  
transporting without 
scanning in reverse  
when A4-R/FOLIO  
paper or LT-R/LG paper 
is detected in a mixed- 
size copying.  
0: Disabled -  
 AMS:A series - Judges as 
A4-R without trans- 
porting in reverse  
with no scanning.  
LT series -...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 180
464-0 Paper 
feeding Feeding retry  
number set- 
ting (lower  
drawer) Plain 
paper
ALL 5
 M Sets the number of 
times of the feeding  
retry from the lower  
drawer. 4
464-1 Others ALL 5 M 4
465-0 Paper  feeding Feeding retry 
number set-
ting 
(PFP upper  
drawer) Plain 
paper
ALL 5
 M Sets the number of 
times of the feeding  
retry from the PFP  
upper drawer. 4
465-1 Others ALL 5 M 4
466-0 Paper...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 181
2
481 Paper  feeding Automatic change of paper  
source PPC 1
 SYS Sets whether or not 
changing the drawer  
automatically to the  
other drawer with the 
paper of the same size  
when paper in the  
selected drawer has run  
out. 
0: OFF 
1: ON (Changes to the drawer with the  
same paper direc- 
tion and size: ex. A4  
to A4)
2: ON (Changes to the 
drawer with the 
same paper size.  
Paper with the...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 182
486 Laser Timing of auto-clearing of 
polygonal motor pre-run- 
ning rotation ALL 0
 SYS Switches the polygonal 
motor to the standby 
rotation when a certain  
period of time has 
passed from the pre- 
running. At this code,  
the period to switch the 
status to the standby  
rotation is set. 
0: 15 sec.1: 30 sec. 
2: 45 sec. 
* This setting is effec-tive when “0” or “2”  
is set at 08-483. 1
488 Laser...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 183
2
508 Image Custom Mode setting PPC 0 SYS 0: Not used
1: Custom Mode 1 when Text/Photo is  
set as a base
2: Custom Mode 2  when Text is set as 
a base
3: Custom Mode 3  when Photo is set  
as a base 1
509 Image Error diffusion and dither  setting at a photo mode 
(Custom Mode) PPC 1
 SYS Switches the image 
processing method 
when Custom Mode 3  
is set.
0: Error diffusion 
1: Dither 1
515 Fuser...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 184
521 Fuser Fuser roller temperature 
during printing 
(Side thermistor/Envelope) ALL 9
 M 0: 140°C 1: 145°C
2: 150°C 3: 155°C
4: 160°C 5: 165°C 
6: 170°C 7: 175°C
8: 180°C 9: 185°C 
10: 190°C 
11: 195°C
12: 200°C 
13: 205°C 
14: 210°C 1
523 Fuser Pre-running time for first  printing 
(Envelope) ALL 10
 M 0: Invalid 1: 1 sec.
2: 2 sec. 3: 3 sec.
4: 4 sec. 5: 5 sec. 
6: 6 sec. 7: 7 sec.
8: 8 sec. 9: 9 sec....