Toshiba Bsx4t Manual

3. ON LINE MODE ENGLISH VERSION EO1-33034 
3.4 Dump Mode
 
E3- 3 
3.4  Dump Mode 
 
 
 
 In Dump mode, any characters sent from the host computer will be 
printed.  Received characters are expressed in hexadecimal values.  This 
allows the user to verify programming commands and debug the 
program. 
For details, please refer to your nearest TOSHIBA TEC service 
representative.  

4. MAINTENANCE ENGLISH VERSION EO1-33034 
4.1 Cleaning
 
E4- 1 
 
4. MAINTENANCE
 
 
 
 
 
 
 
 
 
 
 
 
 
4.1 Cleaning 
 
 
 
4.1.1  Print Head/Platen/
 Sensors 
 
 
 
 
 
 
 
 
 
 
This chapter describes how to perform routine maintenance.  
To ensure the continuous high quality operation of the printer, you should 
perform a regular maintenance routine.  For high throughput it should be 
done on a daily basis.  For low throughput it should be done on a weekly 
basis. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
To...

4. MAINTENANCE ENGLISH VERSION EO1-33034 
4.1 Cleaning
 
E4- 2 
 
 
4.1.2  Covers and Panels 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
4.1.3  Optional Cutter Module 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Wipe the covers and panels with a dry soft cloth or a cloth slightly 
moistened with mild detergent solution.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
The swing cutter and rotary cutter are available as an option.  They are 
both cleaned in the same way.  When removing the Cutter Cover of the 
rotary cutter unit, remove...

4. MAINTENANCE ENGLISH VERSION EO1-33034 
4.2 Care/Handling of the Media and Ribbon
 
E4- 3 
4.2  Care/Handling of the 
Media and Ribbon  
 
 ·  Do not store the media or ribbon for longer than the manufacturer’s  
  recommended shelf life.  
·  Store media rolls on the flat end.  Do not store them on the curved 
sides as this might flatten that side causing erratic media advance and 
poor print quality.   
·  Store the media in plastic bags and always reseal after opening.  
Unprotected media can get...

5. TROUBLESHOOTING ENGLISH VERSION EO1-33034 
5.1 Error Messages
 
E5- 1 
5. TROUBLESHOOTING 
This chapter lists the error messages, possible problems, and their solutions. 
 
 
 
 
 
 
 
5.1 Error Messages 
 
 
 
 
  
Error Messages  Problems/Causes  Solutions 
HEAD OPEN The Print Head Block is opened in 
Online mode. Close the Print Head Block.   
HEAD OPEN   **** Feeding or printing has been attempted 
with the Print Head Block open.  Close the Print Head Block.  Then press 
the [RESTART]
 key. 
COMMS...

5. TROUBLESHOOTING ENGLISH VERSION EO1-33034 
5.2 Possible Problems
 
E5- 2 
5.1  Error Messages (Cont.) 
Error Messages  Problems/Cause  Solutions 
NO PAPER    **** 1.  The media has run out. 
 
2.  The media is not loaded properly. 
 
3.   The media is slack. 1.   Load new media.  Then press the 
[RESTART]
 key. 
2.   Reload the media correctly.  Then 
press the [RESTART]
 key. 
3.   Take up any slack in the media. 
RIBBON ERROR  **** The ribbon is not fed properly. 
 
 
 
 Remove the ribbon, and check...

5. TROUBLESHOOTING ENGLISH VERSION EO1-33034 
5.3 Removing Jammed Media 
E5- 3 
5.3 Removing Jammed 
Media  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 This section describes in detail how to remove jammed media from the 
printer.  
 
 
1.
  Turn off and unplug the printer. 
2.
  Open the Top Cover. 
3.
  Turn the Head Lever to Free
 position, then open the Ribbon Shaft 
Holder Plate. 
4.
  Open the Print Head Block.  
5.
  Remove the ribbon and media. 
 
 
 
 
 
 
 
 
 
 
 
 
 
6.
  Remove the jammed media...

5. TROUBLESHOOTING ENGLISH VERSION EO1-33034 
5.4 Threshold Setting 
E5- 4 
5.4 Threshold Setting 
 To maintain a constant print position the printer uses the Transmissive 
Sensor to detect the gap between labels by measuring the amount of 
light passing through the media.  When the media is pre-printed, the 
darker (or more dense) inks can interfere with this process causing 
paper jam errors.  To get around this problem a minimum threshold can 
be set for the sensor in the following way.  
 
„Threshold...

APPENDIX 1  SPECIFICATIONS ENGLISH VERSION EO1-33034 
A1.1 Printer
 
EA1- 1 
APPENDIX 1  SPECIFICATIONS 
Appendix 1 describes the printer specifications and supplies for use on the B-SX4T printer.  
 
A1.1 Printer 
The following is the printer specifications.  
Model 
Item B-SX4T-GS10-QQ B-SX4T-GS10-QP 
Supply voltage 
Power consumption 
     During a print job 
     During standby AC100 – 120V, 50/60 Hz±10% 
 
1.6 A, 133 W maximum  
0.18 A, 14 W maximum  AC220 – 240V, 50 Hz±10% 
 
1.0 A, 134 W maximum...

APPENDIX 1  SPECIFICATIONS ENGLISH VERSION EO1-33034 
A1.2 Options
 
EA1- 2 
A1.2 Options 
Option Name  Type  Description 
Swing cutter module  B-4205-QM  A stop and cut swing cutter. 
Rotary cutter module  B-8204-QM  Rotary cutter 
Strip module  B-9904-H-QM  This allows use of on-demand (peel-off) operation or to take-up 
labels and backing paper together when using the rewind guide 
plate.  To purchase the strip module, please inquire at your local 
distributor. 
Ribbon saving 
module B-9904-R-QM  This...