Toshiba Bsx4t Manual

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.7 Loading the Media
 
 
E2- 9 
2.7  Loading the Media 
(Cont.) 
 12.
  There are four issue modes available on this printer.  How to set the  
  media for each mode is provided below.  
 
Batch mode
 
In the batch mode, the media is continuously printed and fed until the 
number of labels/tags specified in the issue command have been printed.  
 
 
 
 
 
 
 
 
 
 
 
 
 
Strip mode
 
When the optional Strip Module is fitted, the backing paper is 
automatically...

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.7 Loading the Media
 
 
E2-10 
 
2.7  Loading the Media 
(Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 Build-in rewinder mode
 
The Rewinder Assembly of the Strip Module can be used in batch mode 
to take up the printed media as a Built-in Rewinder.  
 
(1)  Remove the two Black Screws to detach the Front Plate. 
(2)  Attach the Rewinder Guide Plate enclosed with the optional Strip 
Module to the Strip Plate with the SMW-4x8 sems...

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.8 Loading the Ribbon
 
E2-11 
 
 
2.8  Loading the Ribbon  
 
 
 There are two types of media available for printing on: these are thermal 
transfer media and direct thermal media (a chemically treated surface).  
DO NOT LOAD a ribbon when using a direct thermal media. 
 
1.
  Grasp the tabs on the top and bottom of the Ribbon Stoppers and 
move the Ribbon Stoppers back to the end of the Ribbon Shaft.   
 
 
 
 
 
 
 
 
 
 
 
 
 
2.
  Leaving plenty of slack...

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.9 Inserting the Optional PCMCIA Cards
 
E2-12 
 
2.9  Inserting the Optional 
PCMCIA Cards 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
When the optional PCMCIA Interface Board is installed into the printer, 
there will be two PCMCIA slots available as shown in the figure below.  
This allows the use of Flash Memory type Cards or I/O Cards such as 
LAN Cards.  The following paragraphs outline how to insert PCMCIA 
cards. 
1.
  Make sure...

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.10 Test Print
 
E2-13 
2.10 Test Print 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 A print test should be performed to check that the printer is operating 
correctly.   
The following paragraphs guide you through the diagnostic procedure for 
test label printing.  Please follow the step-by-step procedures exactly for 
best results. 
 
1.
  Use label stock for the test print.  For best results, use labels that are 
76 mm or longer in...

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.10 Test Print
 
E2-14 
2.10  Test Print (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 9.
 Press the [PAUSE]
 key and the issue mode setting display will  
  appear.  Select the issue mode with the [FEED]
 or [RESTART]
  
 key. 
 
 
 
 
10.
 Press the [PAUSE]
 key and the media size setting display will 
appear.  Select the media size with the [FEED]
 or [RESTART]
 key. 
 
 
 
 
11.
 Press the [PAUSE]
 key and the paper feed setting display will 
appear.  Select...

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.10 Test Print
 
E2-15 
2.10  Test Print (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 19.
  When you have finished performing the test print operation, turn the 
printer’s power OFF then back to ON and check that the LCD 
Message Display shows ON LINE and that the ON LINE and 
POWER LED lights are illuminated. 
Sample of the slant line (1 dot) test print label
 
 
 
 
 
 
 
 
 
Sample of the slant line...

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.10 Test Print
 
E2-16 
2.10 Test Print (Cont.) 
 
 Sample of the bar code test print label
 
 
 
 
 
 
 
 
 
Sample of the factory test label
 
  

3. ON LINE MODE ENGLISH VERSION EO1-33034 
3.1 Operation Panel 
 
E3- 1 
 
3.  ON LINE MODE
 
 
 
 
3.1 Operation Panel 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
This chapter describes usage of the keys on the Operation Panel in On 
Line mode.  
When the printer is in On Line mode and connected to a host computer, 
the normal operation of printing images on labels or tags can be 
accomplished.  
 
 
 
· 
The figure below illustrates the operation panel and key functions....

3. ON LINE MODE ENGLISH VERSION EO1-33034 
3.2 Operation
 
E3- 2 
3.2 Operation 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
3.3 Reset 
 
 
 
 
 
 
 
 
 
 
 
 
 When the printer is turned on, the “
ON LINE”
 message appears on the 
LCD Message Display.  It is shown during standby or normal printing.  
 
1.
  The printer is turned on, standing by, or printing. 
 
 
 
2.
 If any error occurs during printing, an error message appears.  The 
printer stops printing automatically.  (The number on the right side...