Toshiba Bsx4t Manual

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.4 Connecting the Cables to Your Printer
 
E2- 3 
 
2.4 Connecting the 
Cables to Your 
Printer 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 The following paragraphs outline how to connect the cables from the 
printer to your host computer, and will also show how to make cable 
connections to other devices.  Depending on the application software 
you use to print labels, there are 4 possibilities for connecting the 
printer to your host computer.  These are: 
·
  A serial...

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.5 Connecting the Power Cord
 
E2- 4 
 
 
2.5 Connecting the 
Power Cord
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 1.
  Make sure that the printer Power Switch is in the OFF (
{
{) position. 
 
 
 
 
 
 
 
 
 
 
 
2.
  Connect the Power Cord to the printer as shown in the figure below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
3.
  Plug the other end of the Power Cord into a grounded outlet as shown 
in the figure below. 
 
 
 
 
 
 
 
 
 
 
  
[QQ...

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.6 Turning the Printer ON/OFF
 
E2- 5 
 
2.6  Turning the Printer 
ON/OFF
 
 
 
2.6.1  Turning ON the Printer 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2.6.2  Turning OFF the Printer
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 When the printer is connected to your host computer it is good practice to 
turn the printer ON before turning on your host computer and turn OFF 
your host computer before turning off the printer. 
 
 
1.
  To turn ON the printer power, press...

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.7 Loading the Media
 
E2- 6 
 
2.7 Loading the Media 
 
 
 
 
 
 
 
 
 
 
 
 The following procedure shows the steps to properly load the media into 
the printer so that it feeds straight and true through the printer. 
 
The printer prints both labels and tags. 
 
1.
  Turn off the power and open the Top Cover. 
2.
  Turn the Head Lever to Free
 position, then release the Ribbon Shaft 
Holder Plate.  
3.
  Open the Print Head Block....

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.7 Loading the Media
 
E2- 7 
 
 
2.7  Loading the Media 
(Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 5.
  Put the media on the Supply Shaft. 
6.
  Pass the media around the Damper, then pull the media towards the 
front of the printer.  
7.
  Align the projection of the Supply Holder with the groove of the 
Supply Shaft, and push the Supply Holder against the media until the 
media is held firmly in place.  This will centre the media 
automatically. 
Then turn the...

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.7 Loading the Media
 
E2- 8 
2.7  Loading the Media 
(Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
10.
  Lower the Print Head Block until it stops.  
11.
  After loading the media, it may be necessary to set the Media 
Sensors used to detect the print start position for label or tag 
printing. 
 
Setting the Feed Gap Sensor position
 
(1)  Remove the Locking Screw that secures the Media Sensor. 
(2)  Manually move the Media Sensor so that the Feed Gap Sensor is...

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.7 Loading the Media
 
E2- 9 
2.7  Loading the Media 
(Cont.) 
 12.
  There are four issue modes available on this printer.  How to set the  
  media for each mode is provided below.  
 
Batch mode
 
In the batch mode, the media is continuously printed and fed until the 
number of labels/tags specified in the issue command have been printed.  
 
 
 
 
 
 
 
 
 
 
 
 
 
Strip mode
 
In the strip mode, the backing paper is automatically removed from the 
label...

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.7 Loading the Media
 
 
 
E2-10 
 
2.7  Loading the Media 
(Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 Build-in rewinder mode
 
When the Rewinder Guide Plate is attached, the Take-up Spool can be 
used as a Built-in Rewinder to take up the printed media.  
 
(1)  Remove the two Black Screws to detach the Front Plate. 
 
 
 
 
 
 
 
 
 
 
 
(2)  Attach the Rewinder Guide Plate to the Strip Plate with the SMW-
4x8 sems screws....

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.7 Loading the Media
 
 
 
E2-11 
 
2.7  Loading the Media 
(Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 Cut mode
 
When the optional Cutter Module is fitted, the media is automatically cut.  
A swing cutter and a rotary cutter are available as an option, but they are 
used in the same way. 
Insert the leading edge of the media into the Media Outlet of the Cutter 
Module. 
 
 
 
 
 
 
 
 
 
 
 
 
13.
   If the loaded media is...

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.8 Loading the Ribbon
 
 
E2-12 
 
 
2.8  Loading the Ribbon  
 
 
 There are two types of media available for printing on: these are thermal 
transfer media and direct thermal media (a chemically treated surface).  
DO NOT LOAD a ribbon when using a direct thermal media. 
 
1.
  Rotate the Ribbon Stoppers counterclockwise by 90° and move them 
back to the end of the Ribbon Shafts.  Restore the Ribbon Stoppers to 
the former orientation by turning them...