Toshiba Bsx4t Manual

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.8 Loading the Ribbon
 
E2-13 
2.8  Loading the Ribbon 
(Cont.)  
 
 
 
„Auto Ribbon Saving Mode 
When the auto ribbon saving function is selected, it will be activated to 
reduce ribbon loss when a no print area extends more than 20 mm.  For 
further information on this function, please ask a TOSHIBA TEC 
authorised service representative.  
NOTE: 
Ribbon loss per ribbon saving 
varies according to the relation 
between the outer roll diameter 
of the used...

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.9 Inserting the Optional PCMCIA Cards
 
E2-14 
2.9  Inserting the Optional 
PCMCIA Cards 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
When the optional PCMCIA Interface Board is installed into the printer, 
there will be two PCMCIA slots available as shown in the figure below.  
This allows the use of Flash Memory type Cards or I/O Cards such as 
LAN Cards.  The following paragraphs outline how to insert PCMCIA 
cards. 
1.
  Make sure that...

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.10 Test Print
 
E2-15 
2.10 Test Print 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 A print test should be performed to check that the printer is operating 
correctly.   
The following paragraphs guide you through the diagnostic procedure for 
test label printing.  Please follow the step-by-step procedures exactly for 
best results. 
 
1.
  Use label stock for the test print.  For best results, use labels that are 
76 mm or longer in...

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.10 Test Print
 
E2-16 
2.10  Test Print (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 9.
 Press the [PAUSE]
 key and the issue mode setting display will  
  appear.  Select the issue mode with the [FEED]
 or [RESTART]
  
 key. 
 
 
 
 
10.
 Press the [PAUSE]
 key and the media size setting display will 
appear.  Select the media size with the [FEED]
 or [RESTART]
 key. 
 
 
 
 
11.
 Press the [PAUSE]
 key and the paper feed setting display will 
appear.  Select...

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.10 Test Print
 
E2-17 
2.10  Test Print (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 19.
  When you have finished performing the test print operation, turn the 
printer’s power OFF then back to ON and check that the LCD 
Message Display shows ON LINE and that the ON LINE and 
POWER LED lights are illuminated. 
Sample of the slant line (1 dot) test print label
 
 
 
 
 
 
 
 
 
Sample of the slant line...

2. PRINTER SETUP ENGLISH VERSION EO1-33036 
2.10 Test Print
 
E2-18 
2.10 Test Print (Cont.) 
 
 Sample of the bar code test print label
 
 
 
 
 
 
 
 
 
Sample of the factory test label
 
 
  

3. ON LINE MODE ENGLISH VERSION EO1-33036 
3.1 Operation Panel 
 
E3- 1 
3.  ON LINE MODE
 
 
 
 
3.1 Operation Panel 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
This chapter describes usage of the keys on the Operation Panel in On 
Line mode.  
When the printer is in On Line mode and connected to a host computer, 
the normal operation of printing images on labels or tags can be 
accomplished.  
 
 
 
· 
The figure below illustrates the operation panel and key functions.  
 
 
 
 
 
 
 
 
 
 
The...

3. ON LINE MODE ENGLISH VERSION EO1-33036 
3.2 Operation
 
E3- 2 
3.2 Operation 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
3.3 Reset 
 
 
 
 
 
 
 
 
 
 
 
 
 When the printer is turned on, the “
ON LINE”
 message appears on the 
LCD Message Display.  It is shown during standby or normal printing.  
 
1.
  The printer is turned on, standing by, or printing. 
 
 
 
2.
 If any error occurs during printing, an error message appears.  The 
printer stops printing automatically.  (The number on the right side...

3. ON LINE MODE ENGLISH VERSION EO1-33036 
3.4 Dump Mode
 
E3- 3 
3.4 Dump Mode 
 
 
 
 In Dump mode, any characters sent from the host computer will be 
printed.  Received characters are expressed in hexadecimal values.  This 
allows the user to verify programming commands and debug the 
program. 
For details, please refer to your nearest TOSHIBA TEC service 
representative.  

4. MAINTENANCE ENGLISH VERSION EO1-33036 
4.1 Cleaning
 
E4- 1 
 
4. MAINTENANCE
 
 
 
 
 
 
 
 
 
 
 
 
 
4.1 Cleaning 
 
 
 
4.1.1  Print Head/Platen/
 Sensors 
 
 
 
 
 
 
 
 
 
 
This chapter describes how to perform routine maintenance.  
To ensure the continuous high quality operation of the printer, you should 
perform a regular maintenance routine.  For high throughput it should be 
done on a daily basis.  For low throughput it should be done on a weekly 
basis. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
To...