Toshiba Bsx4t Manual

1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33034 
1.5 Appearance
 
E1- 3 
 
1.5 Appearance 
 
1.5.1 Dimensions 
 
 
 
 
 
 
 
 
1.5.2  Front View 
 
 
 
 
 
 
 
 
 
 
 
 
1.5.3  Rear View
 
 
 
 
The names of the parts or units introduced in this section are used in the 
following chapters. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Dimensions in mm (inches) 
LCD Message Display 
Operation Panel 
Power Switch 
{: OFF 
 |: ON 
Media Outlet 
Top Cover 
Expansion I/O 
Interface Connector 
(Option)...

1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33034 
1.5 Appearance
 
E1- 4 
 
 
1.5.4  Operation Panel 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1.5.5 Interior 
 
   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Please see Section 3.1 for further information about the Operation Panel.  
 
 
 
LCD Message Display  
ON LINE LED  
(Green) 
ERROR LED  
(Red) 
[PAUSE]
 key 
POW ER LED
(Green)
[FEED]
 key
[RESTART]
 key 
Ribbon Stopper
Print Head Block 
Head Lever 
Ribbon ShaftSupply Holder  Locking Ring 
Supply Shaft 
Print Head  
Platen  

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.1 Precautions 
 
E2- 1 
2.  PRINTER SETUP 
 
 
 
 
2.1 Precautions 
 
  
 
This section outlines the procedures to setup your printer prior to its 
operation.  The section includes precautions, connecting cables, 
assembling accessories, loading media and ribbon, inserting the optional 
memory card, and performing a test print. 
 
 
To insure the best operating environment, and to assure the safety of the 
operator and the equipment, please observe the...

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.2 Procedure before Operation 
 
E2- 2 
2.2  Procedure before  
Operation 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2.3  Fitting the Fan Filter 
This section describes the outline of the printer setup. 
 
1.
  Unpack the accessories and printer from the box. 
2.
  Refer to Safety Precautions in this manual and set up the printer at a 
proper location. 
3.
  Fit the Fan Filter to the printer.  (Refer to Section 2.3.) 
4.
  The host computer must have a serial,...

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.4 Connecting the Cables to Your Printer
 
E2- 3 
 
2.4 Connecting the 
Cables to Your 
Printer 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 The following paragraphs outline how to connect the cables from the 
printer to your host computer, and will also show how to make cable 
connections to other devices.  Depending on the application software 
you use to print labels, there are 4 possibilities for connecting the 
printer to your host computer.  These are: 
·  A serial...

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.5 Connecting the Power Cord
 
E2- 4 
 
 
2.5 Connecting the 
Power Cord
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 1.
  Make sure that the printer Power Switch is in the OFF (
{
{) position. 
 
 
 
 
 
 
 
 
 
 
 
2.
  Connect the Power Cord to the printer as shown in the figure below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
3.
  Plug the other end of the Power Cord into a grounded outlet as shown 
in the figure below. 
 
 
 
 
 
 
 
 
 
 
  
[QQ...

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.6 Turning the Printer ON/OFF
 
E2- 5 
 
2.6  Turning the Printer 
ON/OFF
 
 
 
2.6.1  Turning ON the Printer 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2.6.2  Turning OFF the Printer
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 When the printer is connected to your host computer it is good practice to 
turn the printer ON before turning on your host computer and turn OFF 
your host computer before turning off the printer. 
 
 
1.
  To turn ON the printer power, press...

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.7 Loading the Media
 
E2- 6 
 
2.7 Loading the Media 
 
 
 
 
 
 
 
 
 
 
 
 The following procedure shows the steps to properly load the media into 
the printer so that it feeds straight and true through the printer. 
 
The printer prints both labels and tags. 
 
1.
  Turn off the power and open the Top Cover. 
2.
  Turn the Head Lever to Free
 position, then release the Ribbon Shaft 
Holder Plate.  
3.
  Open the Print Head Block....

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.7 Loading the Media
 
E2- 7 
 
 
2.7  Loading the Media 
(Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 5.
  Put the media on the Supply Shaft. 
6.
  Pass the media around the Damper, then pull the media towards the 
front of the printer.  
7.
  Align the projection of the Supply Holder with the groove of the 
Supply Shaft, and push the Supply Holder against the media until the 
media is held firmly in place.  This will center the media 
automatically. 
Then turn the...

2. PRINTER SETUP ENGLISH VERSION EO1-33034 
2.7 Loading the Media
 
E2- 8 
2.7  Loading the Media 
(Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
10.
  Lower the Print Head Block until it stops.  
11.
  After loading the media, it may be necessary to set the Media 
Sensors used to detect the print start position for label or tag 
printing. 
 
Setting the Feed Gap Sensor position
 
(1)  Remove the Locking Screw that secures the Media Sensor. 
(2)  Manually move the Media Sensor so that the Feed Gap Sensor is...