Tone Commander 2260d Installation Instructions

System Programming
Several network interface and operation parameters are programmable by the installer, allowing
compatibility with a wide variety of central office features. The system is pre-programmed at the factory;
many installations will require few changes to these values. Programming is retained in the 2260d’s
memory when power is disconnected. A parameter or feature may be altered at any time without
reprogramming the entire system.
The PC-based Setup Utility provided with the 2260d offers a...

Password Protection
To prevent inadvertent or unauthorized changes to console programming, you can enable password
protection. Passwords consist of four digits entered with the dial pad or the Setup Utility. Three separate
passwords are provided:
Mode Default Password
Console Setup 7743 (SPID)
Name/Autodial 6263 (NAME)
Statistics Reset 7828 (STAT)
When passwords are enabled, the console will prompt for a password whenever a user attempts to access
one of the above programming modes.

Enter the password...

Enter the new password with the dial pad.

Select NEXT, then enter the new password again for confirmation.

Select DONE to enable the new password.
Default Passwords
The default passwords listed in the table above are reloaded whenever the password mode is changed
from disabled to enabled.
Use this procedure if you forget a custom password.

Set option switch 2 OFF.

Cycle power to disable all passwords.

Set option switch 2 ON.

Cycle power again to enable default passwords.
13-102735 Rev. FPage 33...

Page 3413-102735 Rev. F
Tone Commander 2260d Installation Instructions
Lucent
National ISDN
123456
1316361141164621512656
2
327371242174722522757
3
338381343184823532858
4
349391444194924542959
5
3510401545205025553060
Figure 3– 2260d Console Default Key Assignments, Lucent National ISDN 

13-102735 Rev. FPage 35
Tone Commander 2260d Installation Instructions
1316361141164621512656
2
327371242174722522757
3
338381343184823532858
4
349391444194924542959
5
3510401545205025553060
Figure 4– 2260d Console Default Key Assignments, Lucent Custom ISDN
Lucent
Custom ISDN 

Page 3613-102735 Rev. F
Tone Commander 2260d Installation Instructions
1316361141164621512656
2
327371242174722522757
3
338381343184823532858
4
349391444194924542959
5
3510401545205025553060
Figure 5– 2260d Console Default Key Assignments, Nortel National ISDN
Nortel
National ISDN 

13-102735 Rev. FPage 37
Tone Commander 2260d Installation Instructions
1316361141164621512656
2
327371242174722522757
3
338381343184823532858
4
349391444194924542959
5
3510401545205025553060
Figure 6– 2260d Console Default Key Assignments, Siemens National ISDN
Siemens
National ISDN 

Configuration Sheet Preparation
The configuration sheets attached to the back of this manual (starting on page 109) should be filled in with
the setup information for this installation. Instructions for each configuration sheet table, and sample
configuration sheets, are included in this chapter. Sample information is printed initalic block font.
Please leave a copy of the configuration sheets on site.
System Setup

Press the MAINT key to enter Maintenance Mode.

Select SETUP.
The Setup menu will be...

2260d Configuration Sheet #1
SPID and PDN Numbers
SPID for Attendant Call Appearances
(3-20 digits maximum;
exactly 10 digits for Lucent Custom ISDN)42534910000101
SPID for DSS/BLF
(3-20 digits maximum;
exactly 10 digits for Lucent Custom ISDN)42534911000101
PDN for Attendant Call Appearances
(10 digits required for proper operation)4253491000
PDN for DSS/BLF
(10 digits required for proper operation)4253491100
ISDN Version
(check one)

Lucent National ISDN

Lucent Custom ISDN

Nortel National ISDN...

Entering/Editing SPID & PDN, Selecting Switch Type

Select SPID from the Setup menu.
The SPID/PDN/Switch menu for the 2260d console will be displayed.

From the 22d SPID/PDN menu, select EDIT.
The SPID/PDN/Switch editing screen will be displayed.

The blinking cursor will be in the SPID field initially. Using the dial pad, enter the SPID as assigned by
the telco.
Overwrite desired digits where necessary, or select DELETE to delete your choice of a single
character (CHAR), all characters in a field...