Steinberg Cubase SX/SL 3 MIDI Devices And Features Manual

							CUBASE SX/SLMIDI devices 1 – 61
•All the values that have been defined now appear in the Add Parame-
ters dialog and can be assigned to a so called “Formula”.
22.Click in the Formula column for the DevID and enter “DevID”, to set 
this value to a variable called “DevID”.
As there is no “DevID” variable defined yet, you get “error” as a result. 
For now, this can be ignored. We will define the “DevID” variable later.
23.Now you need to set the right address. In the Scale Tune table of the 
manual, “Address1MSB” and “Address2” are set to 0 for all parame-
ters of the “Scale Tune” nodes. Therefore, leave them as they are: al-
ready set to 0.
“Address3” indicates the part which is affected by each Scale Tune 
and ranges from 10H to 20H. Remember: you created the 17 Scale 
Tune nodes by using a variable called “Part” which ranged from 1-17, 
so if you add 15 to this “Part” variable, you get the desired range of 
10H-20H, which is 16-32 in decimal. To achieve this, simply type in 
“Part+15” in the “Formula” column for “Address3”. (You can also use 
other operations in the “Formula” column: “-” (subtraction), “*” (multi-
plication) and “()” (parentheses) for small calculations.)
24.Finally, enter “index” in the Formula column for “Address4LSB” be-
cause this variable will be used to create multiple (12) parameters at 
once, as set in the “Variable” section of the “Add Parameters” dialog. 
Again, “error” is displayed in the Result field, because there is no such 
variable defined yet. In fact “index” is no real variable, because it sim-
ply will be replaced by each of the values in the defined range after 
completion of the dialog.  
						

							CUBASE SX/SL1 – 62 MIDI devices
The dialog should now be set up as follows:
As you may have noticed, the variable “x” is automatically assigned to 
the “Data” value. “x” stands for the value that is represented by this 
parameter and is always defined individually by each parameter. If you 
later assign a control like a fader to this parameter, this fader will con-
trol and modify “x”. “x” is automatically assigned to the last value of the 
message, but can be freely assigned to any other value.
25.Click OK to close the dialog.
In the device editor, small plus symbols are now displayed next to the 
Scale Tune nodes, indicating further content.
Before looking into these nodes, you should add the missing “DevID” 
variable to the root of the device, because this is a global value that 
affects the device as a whole. 
26.Select the “Roland JV-1080” node, click the “Add Variable” button 
and rename it to “DevID”. Normally, you can keep the default value 
setting of “0”, except if your hardware device is set to another value.  
						

							CUBASE SX/SLMIDI devices 1 – 63
27.Now, let’s look into the Scale Tune 1 node by clicking its plus symbol.
You can now browse the parameters, to verify that the correct MIDI 
messages are transmitted. You can of course also do this for any of 
the other nodes.
28.The next step is to rename the parameters according to the “Scale 
Tune” table of the device’s manual by selecting each of the 12 param-
eters and entering their correct name in the “Name” field.
Now, the parameters should be displayed as follows:
…to display the parameters 
for the node.
Click here…    
						

							CUBASE SX/SL1 – 64 MIDI devices
•If you open any of the other Scale Tune nodes now, you’ll see that the 
names of the parameters have also changed. This is what was meant 
by “alias copies” in the beginning. Furthermore, you will notice that if 
you add a panel to one of the Scale Tune nodes (see page 20), it will 
be added to all of them, which makes it much easier to create panels 
with repeating sections.
29.Now, you need to add parameters to another node, “System Common”. 
In the list to the left, select “System Common”.
30.Click the Add Parameters button and select the Sysex message 
“Roland JV-1080 DataSet1 7 Bit” you created earlier.
31.Now set set up the DevID as described before.
See page 61.  
						

							CUBASE SX/SLMIDI devices 1 – 65
32.Activate the Create Multiple checkbox and enter a range of 0-81, be-
cause the System Common table in the manual of the JV-1080 con-
tains 82 parameters, starting with an index of “0”.
Address1MSB, Address2 and Address 3 are all 0 for all System Common parameters, 
so leave them as they are. Enter “index” in the Formula column for Address4LSB to ad-
dress each of the 82 parameters separately. The dialog should now look like this:  
						

							CUBASE SX/SL1 – 66 MIDI devices
When you click OK, you will notice that 82 new parameters have been 
added to the System Common node.
You can now set the Names, Min, Max and Default values for each of 
the parameters according to the specifications in the System Com-
mon table, as described earlier.
You should now be familiar enough with the basic procedures to con-
tinue with other parameter settings and adjustments and to finally cre-
ate your own specific devices.  
						

							CUBASE SX/SLMIDI devices 1 – 67
About Studio Connections (Cubase SX only)
Studio Connections is the name of an initiative led by Steinberg and 
Yamaha. The initiative intends to create industry standards for totally in-
tegrated system environments using software and hardware products.
First implementation stage of the Studio Connections open standard 
is the integration and support of Yamaha’s Studio Manager 2 and 
Total Recall for compatible hardware devices.  
						

							CUBASE SX/SL1 – 68 MIDI devices
If you have a SM2 component installed, there is an additional menu 
item in the Devices menu for the Yamaha Studio Manager window.
Total Recall
Total Recall means that you can save and recall all settings of your 
hardware and software products by opening one integrated file in a 
DAW such as Cubase or Nuendo. Also you will have instant and or-
ganized access to hardware editors.
When you load a project or switch to another active project that con-
tains SM2 data, the Total Recall Synchronization dialog appears:
This dialog can also be opened any time from the Studio Manager’s 
Synchronize menu. Click OK for the Dump to start.   
						

							CUBASE SX/SLMIDI devices 1 – 69
Virtual MIDI Devices
If you have a new OPT component (e. g. the DM2000) which uses a 
new special interface, you can access these components as virtual 
MIDI Devices in the MIDI track’s out port selection.
When a MIDI Track is routed to such a device, the “Panel” Button 
becomes available.
Click the Panel button…
…to open the editor window for the device.
•Please also refer to the separate Yamaha documentation.   
						

							CUBASE SX/SL1 – 70 MIDI devices