Starplus Triad Xts Digital Telephone Systems Station User Guide

80 Personalized Messages
To cancel the message:
1. Either dial the Personal Messages code [633] + [00], dial 
[662], or press the DND button.
2. Replace handset. DND button LED extinguishes.
SINGLE LINE TELEPHONE
Not applicable
Scrollable Canned Messages
The Scrollable Canned Message feature allows you to use a 
single digit [#] or [
6] to scroll through the canned messages 
and select one. When the desired message is displayed, 
pressing the hold button places that message on the station 
LCD. This...

Personalized Messages 81
4. When the desired message is shown on the LCD display, 
pressing the HOLD button activates that message on your 
station. Confirmation tone sounds and the DND button LED 
flashes.
To cancel the message:
1. Either dial the Personal Messages code [633] + [00], dial 
[662], or press the DND button.
2. Replace handset. DND button LED extinguishes.
SINGLE LINE TELEPHONE
Not applicable
Personal Messages Flexible Button
You can program the code [633] onto a flexible button to 
speed...

82 PBX/Centrex Codes on a Flex Button
To use the flexible button, press that flexible button, then 
either:
Dial the 2-digit message number (00-10 or 18-30) to 
activate the message. Confirmation tone sounds and DND 
button LED flashes.
-or-
Press [#] to scroll forward or [
6] to scroll backward through 
the list. When desired message is shown on the LCD, press 
HOLD to activate that message on your station. 
Confirmation tone sounds and DND button LED flashes
SINGLE LINE TELEPHONE
Not applicable...

Release Button 83
Release Button
The Release Button feature lets the station user disconnect calls 
while off-hook (on handset, not speakerphone), speeding up 
call handling time.
While off-hook (on handset, not speakerphone) on an 
intercom call, transfer sequence, page announcement, or 
CO call:
Press the preprogrammed RELEASE button [641] to 
terminate intercom call, transfer sequence, page 
announcement or CO call.
Redial
Last Number Redial
1. Press SPEED.
2. Press pound [#] key. The last number...

84 Redial
Repeat Redial 
A keyset station user places a CO call and receives a Busy or 
No Answer:
1. Press the preprogrammed RPT REDIAL flexible button [643]. 
The LCD prompts the user for a timer value.
2. Enter a valid number (006-999 seconds) for the Repeat 
Redial Timer. Default value is 060 (one minute). A 
confirmation tone sounds and the station user goes on-
hook. The flexible button LED lights steady.
When the timer expires, the station is signaled via a CO line 
queue indication on the RPT...

Ring Down / Hot Line / Off-Hook Preference 85
SINGLE LINE TELEPHONE
Not applicable
Ring Down / Hot Line / Off-Hook 
Preference
If your phone has been programmed for Off-Hook Preference, 
you can access an outside line, or a feature by going off-hook or 
pressing the ON/OFF button. It simulates the depression of a 
specific button and can be programed by a station user or a 
database administration programmer using code [691] + the 
button number.
While Off-Hook Preference is enabled, you may access...

86 Ring Tone
2. Dial the desired button number. Refer to the following 
chart.
To disable Off-Hook Preference:
1. Dial [691] on the dial pad.
2. Dial [00] on the dial pad.
SINGLE LINE TELEPHONES
When establishing an Off-hook Preference for SLT stations, it 
is necessary to program the SLTs CO line or line group, to 
access when going off-hook.
Single line telephones can bypass Off-hook Preference by 
doing a hookflash and then dialing their extension number.
Ring Tone
To select a distinctive ring tone...

Ring Tone 87
2. Enter a valid tone number. The telephone speaker sounds a 
steady tone that correlates to the 2-digit entry. The 2-digit 
tone number displays in the lower left corner of the LCD 
display.
The ringing choices are as follows:
3. When the desired tone is selected (default ringing code is 
set to 00), press the SPEED button to save it as the tone to 
present when the station is tone rung. A confirmation tone 
sounds.
CO RING TONE*/FREQUENCY
Tone (#) Freq Tone (#) Freq Tone (#) Freq
00...

88 Serial Number
Serial Number
When feature code [609] is dialed on a display telephone, the 
serial number of the MPB displays. The serial number is used 
when you activate or upgrade the system.
Software Identification
When a station dials feature code [610] on a display telephone, 
the system expects the next digits dialed to be a software 
identification code. This code is used to upgrade to a new 
version of software, e.g. upgrade from basic software to ACD 
software.
1. Dial feature code [610] on a...

Speakerphone 89
The bottom line of the LCD shows the features that are 
enabled for your software, e.g., BASIC or ACD.
Speakerphone
1. Press ON/OFF to ON. (Intercom dial tone sounds.)
2. Press the DSS key of the desired party or press an available 
OUTSIDE LINE button and dial number.
Speakerphone is activated.
3. Press ON/OFF to end call.
Speed Dial
A keyset user can associate up to 20 frequently dialed numbers 
as Station Speed Numbers (9000 to 9019). Telephone numbers 
can be up to 24 digits including...