Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

Programming LCR TablesB-11
Appendix B - Least Cost Routing
2. Enter the table information as follows:

T T = Insert/Delete Table Number 00–19

X = [0] Pre-Delete numbers (first digits dialed in the number),
-or-
[1] Pre-Insert numbers (insert digits in front of number dialed,
-or-
[2] Post-Insert numbers (insert digits behind number dialed).

DDD = Digits (up to 16-digits may be deleted from the beginning
of the number dialed and up to 40 digits can be inserted (20 pre and 20 post).
3. Press the HOLD...

B-12Programming LCR Tables
Appendix B - Least Cost Routing
Entries in the Daily Start Time table are used to select the time period to reference in the 
weekly schedule. Based on the time a call is placed, the daily start time table selects the time 
period to choose in the weekly schedule. The weekly schedule is then used to determine the 
time period route list in the Route List Table to use for routing the call for a particular day of 
the week. Times are entered in the 24-hour format.
Figure B-2:...

Programming LCR TablesB-13
Appendix B - Least Cost Routing
EXAMPLE -- If a call is placed at 5:45 pm on a Monday, then according to the Daily Start Time 
Table (using default values) the entry for time period two of the weekly schedule is checked. 
Because it is Monday the entry for time period two on Monday is used and the result is that the 
Time Period Route List number two (again using default values) is used for all routes. Thus, the call 
is routed according to the entries in Time Period Two Route...

B-14Programming LCR Tables
Appendix B - Least Cost Routing
LCR Routing for Toll Information
Description
The LCR Routing for Toll Information feature adds provisions to the LCR call processing which 
allows common call routing for all toll information calls. 1-(XXX) 555-1212, (XXX) 555-1212, 
1-555-1212, and 555-1212 calls are intercepted and sent to a selected route in the Route List 
Table.
Numbers dialed are integrated and if it is determined to be a toll information call, either 
preceded with an area...

Programming LCR TablesB-15
Appendix B - Least Cost Routing
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … LCR Call Progress feature is enabled.
Default LCR Database
Description
In an effort to decrease installation and set up time usually associated with LCR, a default LCR 
database was incorporated.
The default LCR database provides basic routing for local and long distance dialing. Default 
entries have been made in the 3-Digit Table for local office codes (NNXs) and all area...

B-16Programming LCR Tables
Appendix B - Least Cost Routing
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the FORCE LCR flexible button (Button #11). The following message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
Conditions
» Only one station at...

Programming LCR TablesB-17
Appendix B - Least Cost Routing
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-351) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates....

B-18Programming LCR Tables
Appendix B - Least Cost Routing
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Enable / Disable Least Cost Routing
Description
To use Least Cost Routing, it must be enabled. Before enabling LCR, refer to the Least Cost 
Routing programming tables.
After the tables are...

Programming LCR TablesB-19
Appendix B - Least Cost Routing
Programming Steps
1. Press the CALL COST DISPLAY flexible button (FLASH 05, Button #11).
2. Enter a 0 or 1 that corresponds with the following entries:
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Call Cost Display is disabled.
Conditions
» The user must have LCR enabled to get the Call Cost Display.
Initialize LCR Tables
Description
The LCR Tables may be initialized to set all tables to...

B-20Programming LCR Tables
Appendix B - Least Cost Routing
Programming Steps
1. Press the LCR TABLES flexible button (FLASH 80, Button #7). The following message 
displays:
2. Press the HOLD button. A confirmation tone sounds.
Print LCR Tables
Description
The Print LCR Tables command dumps the entire database as a permanent record which can 
serve as a hardcopy of the database. The system baud rate must match that of the printer or 
receiving device.
When printing information from the LCR Tables, the...