Sony Xb10 User Manual

							If  [SRS - XB10] does  not  appear on the  screen, repeat the  procedure from step .
A  passkey  may be  called “Passcode,” “PIN code,” “PIN number” or “Password.”*
When the  following screen  appears, click  [Close ].
The computer  begins  installing the  driver.
The “”  mark will  appear in  the  bottom left  of the  [SRS - XB10] icon during  installation.  When the  “”  mark
disappears,  driver installation is complete. Proceed to the  next step (substep 5).
Depending on the  computer, installation may take time.  If  driver installation takes  too  much time,  the  auto  power off
function of the  speaker  will  cause it to turn off automatically. If  this  happens, turn on the  speaker  again.
4 .
Double - click  on [SRS - XB10] in  [ Devices ].5 .
Click  [Listen to Music].6 .
36  
						

							Hint
For details on  operating your  computer, refer to  the  operating instructions supplied with the  computer.
If  your  computer does not  have a  BLUETOOTH wireless function, it will  be  necessary  to  connect a  commercially  available  BLUETOOTH  adaptor
to  the  computer.
When the  speaker  is connected, a  checkmark will  appear.
Check that the   ( BLUETOOTH )  indicator has  switched from flashing  to a steady light.
When the  speaker  is connected to the  computer, the  
 ( BLUETOOTH )  indicator  stays  lit. You  can enjoy  playing  back music
from your  computer.
4
37  
						

							Note
The pairing  mode of  the  speaker  is released  after  about 1  minute  and  the   (BLUETOOTH ) indicator flashes slowly.  However, when  pairing
information  is not  stored in the  speaker,  such  as at  the  factory  settings, the  pairing  mode is not  released.  If  the  pairing  mode is released  before
finishing  the  process, repeat  from step 
.
Once  the  BLUETOOTH  devices  are paired, there  is no  need to  pair  them again, except  in the  following cases:
Pairing  information  has been deleted  after  repair,  etc.
The speaker  is already  paired with 8  devices  and  another  device is to  be  paired. 
The speaker  can be  paired with up  to  8  devices.  If  a  new  device is paired after  8  devices  have already  been paired, the  paired device with the
oldest  connection  time is replaced  by the  new  one.
The pairing  information  of  the  speaker  has been deleted  from the  BLUETOOTH  device.
The speaker  is initialized.
All  pairing  information  will  be  deleted.
The speaker  can be  paired with multiple devices,  but  can only  play  music from one  paired device at  a  time.
Related Topic How  to make a  wireless connection with  BLUETOOTH  devices
Connecting with  a  paired  computer  (Windows 7 )
Listening  to music of a  device via BLUETOOTH  connection
Terminating the  BLUETOOTH  connection (After use)
4- 694- 214- 11(2)  Copyright 2017  Sony Corporation
38  
						

							Help Guide
Wireless  Speaker
SRS-XB10
Connecting with a paired computer (Windows  10)
Do the  following before starting.
If  you have  connected the  speaker  with  the  other device,  turn off the  BLUETOOTH  function on the  device.
Stop playback  on the  computer.
Turn down  the  volume of the  computer  and speaker  to avoid  any sudden loud sound output  from the  speaker.
Activate  the  BLUETOOTH  function on your  computer. For details on how to activate the  BLUETOOTH  function,  refer to the
operating  instructions supplied with  the  computer.
Turn on  the  speaker.
The 
 ( BLUETOOTH )  indicator  flashes  in  white.
When you turn on the  speaker, the  speaker  tries to make a  BLUETOOTH  connection with  the  last  connected BLUETOOTH
device.  If  the  device is nearby and its BLUETOOTH  function is on,  the  BLUETOOTH connection is established automatically
and the  
 ( BLUETOOTH )  indicator  stays  lit. When you want to connect another  BLUETOOTH  device,  terminate  the  current
BLUETOOTH  connection by operating  the  currently connected BLUETOOTH  device.
1
Search for the  speaker  on  the  computer.
2 Select  [
 ( Action  Center )] –  [ Bluetooth] in  the  taskbar on the  right - bottom of the  screen.1 .
39  
						

							Select  [Connect ] in  the  Action  Center  on the  right - bottom of the  screen.2 .
Select  [SRS - XB10].
[Connected music] will  be displayed on the  screen.
3 .
Check that the   ( BLUETOOTH )  indicator has  switched from flashing  to a steady light.
When the  speaker  is connected to the  computer, the  
 ( BLUETOOTH )  indicator  stays  lit. You  can enjoy  playing  back music
from your  computer.
3
40  
						

							Hint
The procedure explained  above is for guidance only.  For details, refer to  the  operating instructions supplied with the  computer.
You can perform pairing  or connect to  another  BLUETOOTH device even when  a  BLUETOOTH connection  is established. In  this  case,  the
previous connection  will  be  disconnected.
When you turn on  the  speaker  or the  BLUETOOTH  mode, the  speaker  tries to  make a  BLUETOOTH connection  with the  last  connected
BLUETOOTH  device. If  the  device’s BLUETOOTH  function is on,  the  BLUETOOTH connection  is started automatically.
Note
If  the  speaker  tries to  reconnect  with the  last  connected BLUETOOTH  device, the  connection  may fail.  In  this  case,  turn off  the  BLUETOOTH
function on  the  BLUETOOTH  device, or turn off  the  BLUETOOTH  device.
Related Topic
How  to make a  wireless connection with  BLUETOOTH  devices
Pairing and connecting with  a  computer  (Windows 10 )
Listening  to music of a  device via BLUETOOTH  connection
Terminating the  BLUETOOTH  connection (After use)
4- 694- 214- 11(2)  Copyright 2017  Sony Corporation
41  
						

							Help Guide
Wireless  Speaker
SRS-XB10
Connecting with a paired computer (Windows  8)
Before  operating  the  speaker, be sure  to do the  following:
Depending on your  computer, it may be necessary  to turn on the  built- in  BLUETOOTH  adaptor. For details on how to turn on
a  built- in  BLUETOOTH  adaptor, refer to the  operating  instructions supplied with  the  computer.
If  the  speaker  was  previously paired  with  a  different device,  turn off the  BLUETOOTH  function for  the  other device.
Turn on  the  speaker.
The 
 (BLUETOOTH )  indicator  begins  to flash in  white.
When you turn on the  speaker, the  speaker  tries to make a  BLUETOOTH  connection with  the  last  connected BLUETOOTH
device.  If  the  device is nearby and its BLUETOOTH  function is on,  the  BLUETOOTH connection is established automatically
and the  
 ( BLUETOOTH )  indicator  stays  lit. When you want to connect another  BLUETOOTH  device,  terminate  the  current
BLUETOOTH  connection by operating  the  currently connected BLUETOOTH  device.
1
Search for the  speaker  on  the  computer.
2 Select  [Desktop ] from the  Start menu.
1 .
Align your  mouse  with  the  right  side of the  screen  (if using  a  touch panel, swipe  from the  right  edge of the  screen), and
select [Settings ] from the  charms that are displayed.2 .
42  
						

							When the  [Settings] charms are displayed, click  [Control Panel ].3 .
When [All Control Panel  Items] is displayed, select [ Sound].
If  the  [Control Panel ] screen  appears instead of [All Control Panel  Items],  select [Large  icons ] or [Small icons ] from the [ View  by] menu in  the  top  right  corner of the  screen.4 .
Confirm [SRS - XB10 Stereo ] on the  [Sound] screen.
If  there is a  checkmark (green) on [SRS - XB10 Stereo ],  proceed to step 
.
5 .
43  
						

							If  there is not  a  checkmark (green) on [SRS - XB10 Stereo],  proceed to the  next step (substep 6).
If  [SRS - XB10 Stereo ] does  not  appear,  right - click  on the  [ Sound] screen, and select [Show Disabled Devices ] from
the  menu that appears. Then proceed to the  next step (substep 6).
Right - click  on [SRS - XB10 Stereo ],  and select [Connect] from the  menu that appears.
When the  speaker  is connected, a  checkmark will  appear on [SRS - XB10 Stereo ] on the  [Sound] screen. Proceed to step
6 .
44  
						

							.
If  you cannot  click  [Connect] for  [SRS - XB10 Stereo ],  select [Disable] for  the  [Default  Device] that currently has a
checkmark (green).
Check that the   ( BLUETOOTH )  indicator has  switched from flashing  to a steady light.
When the  speaker  is connected to the  computer, the  
 ( BLUETOOTH )  indicator  stays  lit. You  can enjoy  playing  back music
from your  computer.
3
45