Sony Vpl Csx6 Projector User Manual

31 GBProjecting
Setting Up and Projecting
To freeze the image projected (Freeze function)
Press the FREEZE key. “Freeze” appears when the key is pressed. This 
function works when a signal from a computer is input or when a still picture 
stored in a Memory Stick is projected (VPL-CX6 only).
To restore the original screen, press the FREEZE key again. 

GB 32Using the MENU
BAdjustments and Settings Using the Menu
Using the MENU
The projector is equipped with an on-screen 
menu for making various adjustments and 
settings. The setting items are displayed in a 
pop-up menu or in a sub menu.  If you select 
an item name followed by dots (...), a sub 
menu with setting items appear. You can 
change the tone of the menu display and the 
menu language displayed in the on-screen 
menu.
To change the menu language, see  
“Selecting the Menu Language” on page...

33 GBUsing the MENU
Adjustments and Settings Using the Menu
4Make the setting or adjustment on an 
item.
 When changing the adjustment level:
To increase the number, press the M or , key.
To decrease the number, press the m 
or < key.
Press the ENTER key to restore the 
previous screen.
 When changing the setting:
Press the M or m key to change the 
setting.
Press the ENTER or < key to restore 
the previous screen.
When setting the Menu Language, see 
“Selecting the Menu Language” on page 22.
To clear...

GB 34The PICTURE SETTING Menu
The PICTURE 
SETTING Menu
The PICTURE SETTING menu is used for 
adjusting the picture or volume. 
Items that cannot be adjusted depending on 
the input signal are not displayed in the 
menu. 
For details on the unadjustable items, see 
page 51.
Picture Mode
Selects the picture mode.
Dynamic: Emphasizes the contrast to 
produce a “dynamic” picture.
Standard: Normally select this setting.  If 
the picture has roughness with the 
“Dynamic” setting, this setting reduces 
the...

35 GBThe INPUT SETTING Menu
Adjustments and Settings Using the Menu
Sharpness
Selects the picture sharpness from among 
“High,” “Middle” and “Low.”  The “High” 
setting makes the picture sharp; the “Low” 
setting makes it soft.
RGB Enhancer
Adjusts the picture sharpness when RGB 
signals are input.
The higher the setting, the sharper the 
picture. The lower the setting, the softer the 
picture.
Gamma Mode
Selects a gamma correction curve.
Graphics: Improves the reproduction of 
halftones. Photos can be...

GB 36The INPUT SETTING Menu
by switching to the wide mode may constitute 
an infringement of the rights of authors or 
producers, which are legally protected.
Adjust Signal... Menu Items
(Only when the RGB signal is input)
Dot Phase
Adjusts the dot phase of the LCD panel and 
the signal output from a computer. 
Adjust the picture further for finer picture 
after the picture is adjusted by pressing the 
APA key.
Adjust the picture to where it looks clearest. 
H Size
Adjusts the horizontal size of picture...

37 GBThe SET SETTING Menu
Adjustments and Settings Using the Menu
Since the data is recalled from the preset 
memory about the following signals, you 
can use these preset data by adjusting “H 
Size.” Make fine adjustment by adjusting 
“Shift.” 
When the aspect ratio of input signal is other 
than 4:3, a part of the screen is displayed in 
black.
The SET SETTING 
Menu
The SET SETTING menu is used for 
changing the settings of the projector.
Smart APA
Activates or deactivates the Smart APA 1).
On:...

GB 38The MENU SETTING Menu
Input-A Signal Sel.
Selects the computer, component or video 
GBR signal input from the INPUT A 
connector.
If the setting is not correct,  the color of the 
picture becomes strange or “Please check 
Input-A Signal Sel.” appears on the screen and 
the picture is not displayed.
Color System
Selects the color system of the input signal.
If you select “Auto,” the projector detects 
the color system of the input signal 
automatically.  If the picture is distorted or 
colorless,...

39 GBThe INSTALL SETTING Menu
Adjustments and Settings Using the Menu
The INSTALL 
SETTING Menu
The INSTALL SETTING menu is used for 
changing the settings of the projector.
Tilt...
Adjusts the position (height) of the projected 
picture.  Pressing the f on the TILT 
adjustment key or M/, key on the Remote 
Commander, the more the projector tilts and 
the higher the position of the picture. 
Pressing the F on the TILT adjustment key 
or m/< key on the Remote Commander,  
the less the projector tilts and...

GB 40The INFORMATION Menu
The INFORMATION 
Menu
The INFORMATION menu displays the 
horizontal and vertical frequencies of the 
input signal and the used time of the lamp.
fH
Displays the horizontal frequency of the 
input signal.
The displayed value is approximate.
fV
Displays the vertical frequency of the input 
signal.
The displayed value is approximate.
Lamp Timer
Indicates how long the lamp has been turned 
on.
These only display on the screen. You cannot 
alter the display.
Menu Items
Note
Input A...