Sony Vpl Csx6 Projector User Manual

11 GBLocation and Function of Controls
Overview
8Control/Connector panel
For details, see “Control Panel” and 
“Connector Panel” on page 12.
9Rear remote control detector 
0Ventilation holes (intake)
qaVentilation holes (intake)/Lamp 
cover
qsPowered tilt adjuster
qdAdjuster (hind pad)
Turn the adjuster to the right or left for 
minor tilt adjustment of the projected 
picture.
qfSpeaker
qgSecurity lock 
Connects to an optional security cable 
(Kensington’s).
Web page address: 
http://www.kensington.com/...

GB 12Location and Function of Controls
1POWER SAVING indicator
Lights up when the projector is in power 
saving mode. When “Power Saving” in 
the SET SETTING menu is set to “ON,” 
the projector goes into power saving 
mode if no signal is input for 10 minutes. 
Although the lamp goes out, the cooling 
fan keeps running. The power saving 
mode is canceled when a signal is input 
or any key is pressed. In power saving 
mode, any key does not function for the 
first 60 seconds after the lamp goes out....

13 GBLocation and Function of Controls
Overview
2USB connector (USB plug for 
upstream, 4-pin)
Connect to the USB connector on a 
computer. When you connect the 
projector to the computer, you can 
control the mouse function with the 
supplied Remote Commander. (When 
you use the VPL-EX1, an optional 
Remote Commander is required to 
control the mouse function with a 
Remote Commander.)  The supplied 
application software (VPL-CX6 only) 
can be installed in the computer attached 
to this connector....

GB 14Location and Function of Controls
 You can cancel the adjustment by 
pressing the APA key again while 
“Adjusting” appears on the screen.
 The picture may not be adjusted properly 
depending on the kinds of input signals.
 Adjust the items “Dot Phase,” “H Size” 
and “Shift”  in the INPUT SETTING 
menu when you adjust the picture 
manually.
3PIC MUTING key
Used to mute the picture temporarily. 
Press again to restore the picture.
4ENTER key
5Keys emulate a mouse
Functions like a mouse of a...

15 GBLocation and Function of Controls
Overview
To install batteries
1Push and slide to open the lid, then 
install the two size AA (R6) batteries 
(supplied) with the correct polarity.
2Replace the lid.
For VPL-EX1
1I / 1 (on/standby) key
2ENTER/arrow key (M/m/

GB 16Location and Function of Controls
Before using the Remote 
Commander
Pull out the clear film from the lithium 
battery holder.
To replace battery
1Release the lock of the lithium battery 
holder by picking it, and pull out the 
holder from the Remote Commander.
2Install the lithium battery.
3Put the lithium battery holder back 
into the Remote Commander.
Notes on the lithium battery
 Keep the lithium battery out of the reach of 
children.
 Should the battery be swallowed, 
immediately consult a...

17 GBInstalling the Projector
Setting Up and Projecting
BSetting Up and Projecting
Installing the Projector
This section describes how to install the projector.
The distance between the lens and the screen varies depending on the size of 
the screen. Use the following table as a guide. 
VPL-CS6/VPL-CX6
There may be a slight difference between the actual value and the design value shown 
in the table above.
VPL-EX1 
There may be a slight difference between the actual value and the design value shown 
in...

GB 18Connecting the Projector
Connecting the Projector
When you connect the projector, make sure to:
 Turn off all equipment before making any connections.
 Use the proper cables for each connection.
 Insert the cable plugs firmly; loose connections may increase noise and 
reduce performance of picture signals. When pulling out a cable, be sure to 
pull it out from the plug, not the cable itself
To connect the projector, refer to the illustrations on the next and the 
following pages.
This section...

19 GBConnecting the Projector
Setting Up and Projecting
To connect an IBM PC/AT compatible computer
On the USB function
When connecting the projector to a computer by using the USB cable for the 
first time, the computer recognizes the following devices automatically.
1USB hub (general use) (VPL-CX6 only)
2USB human interface device (wireless mouse function)
3USB human interface device (projector control function) (VPL-CX6 only)
Recommended operating environment
When you use the USB function, connect the...

GB 20Connecting the Projector
To connect a Macintosh computer 
To connect a Macintosh computer equipped with video output connector of a 
type having two rows of pins, use a commercially available plug adaptor. 
When you connect a USB capable Macintosh computer using the USB cable 
to the projector, wireless mouse functions become available.
The supplied software does not run on Macintosh computer. 
This section describes how to connect the projector to a VCR and 15k RGB/
component equipment. 
For more...