Sony Vpl Csx6 Projector User Manual

21 GBConnecting the Projector
Setting Up and Projecting
To connect a 15k RGB/Component equipment
  
 Set the aspect ratio using “Wide Mode” in the INPUT SETTING menu according to 
the input signal.
 When you connect the unit to 15k RGB or component video equipment, select video 
GBR or component with the “Input-A Signal Sel.” setting in the SET SETTING 
menu.
 Use the composite sync signal when you input the external sync signal from 15k 
RGB/component equipment. 
Notes
AUDIO VIDEOPOWER
SAVING
MENU
S...

GB 22Selecting the Menu Language
Selecting the Menu Language
You can select one of thirteen languages for displaying the menu and other on-
screen displays. The factory setting is English.
To change the menu language, proceed as follows:
1Open the connector panel, then plug the AC power cord into a wall outlet.
2Press the I / 1 key to turn on the projector.
3Press the MENU key.
The menu appears.
The menu presently selected is shown as a yellow button.
I / 1
INPUT
FREEZE
MENU ENTER
KEYSTONEMS...

23 GBSelecting the Menu Language
Setting Up and Projecting
4Press the M or m key to select the MENU SETTING menu, then press the 
, or ENTER key.
The selected menu appears.
5Press the M or m key to select “Language,” then press the , or ENTER 
key.
6Press the M, m, < or , key to select a language, then press the ENTER 
key.
The menu changes to the selected language.
To clear the menu
Press the MENU key.
The menu disappears automatically if a key is not pressed for one minute.
Input A
:
:
:
:A
Input A:
:...

GB 24Projecting
Projecting
1Open the connector panel, plug the AC power cord into a wall outlet, then 
connect all equipment.
The ON/STANDBY indicator lights in red and the projector goes into 
standby mode. 
2Press the I / 1 key.
The ON/STANDBY indicator lights in green and the Intelligent Auto-setup 
starts.  The lens protector opens, and the powered tilt adjuster rises and stops at 
the previously adjusted position.
When the projector is turned on, the Startup screen is projected (VPL-CX6 
only).
For...

25 GBProjecting
Setting Up and Projecting
4Press the INPUT key to select the input source. 
Smart APA (Auto Pixel Alignment) adjusts the picture of the connected 
equipment so that it is projected clearly.
 If “Auto Input Search” is set to “On,” the projector searches for the signals from 
the connected equipment and displays the input channel where the input signals 
are found.
For details, see “Auto Input Search” in the SET SETTING menu on 
page 37.
 The Smart APA is effective for the input signal...

GB 26Projecting
The auto V keystone adjustment may not correct the trapezoidal distortion perfectly, 
depending on the room temperature or the screen angle. In this case, adjust it manually. 
Press the KEYSTONE key (VPL-CS6/CX6) or the D KEYSTONE key (VPL-EX1) on 
the Remote Commander until “V Keystone” appears on the screen, and adjust the value 
with the M/m/

27 GBProjecting
Setting Up and Projecting
To Use the security lock
1Press the MENU key and then, in the INSTALL SETTING menu, turn on 
the 
“Security Lock” setting.
2Enter the password.
Use the MENU, M/m/

GB 28Projecting
4The setting for security lock is completed.
5Turn the main power off and disconnect the AC power cord.
The security lock is set to on, then it becomes effective. The screen for entering 
the password is displayed when the power is turned on the next time. 
 You will not be able to use the projector if you forget your password and the password 
administrator is not available. Be please aware that using the security lock can prevent 
valid usage in such cases. It is recommended that you...

29 GBProjecting
Setting Up and Projecting
To turn off the power
1Press the I / 1 key.
“POWER OFF?  Please press I / 1 key again.” appears to confirm that you 
want to turn off the power.
A message disappears if you press any key except the I / 1 key, or if you do not 
press any key for five seconds.
2Press the I / 1 key again.
The powered tilt adjuster is put away in the projector and the lens protector 
closes.  The ON/STANDBY indicator flashes in green and the fan continues to 
run for about 90 seconds...

GB 30Projecting
To enlarge the image (Digital Zoom function)
You can select a point in the image to enlarge.  This function works when a 
signal from a computer is input, or when a still picture (except a movie picture) 
stored in a Memory Stick is projected (VPL-CX6 only).
This function does not work when a video signal is input.
1Project a normal image, and press the D ZOOM + key on the Remote 
Commander.
The digital zoom icon appears in the center of the image.
2Move the icon to the point on the image...