Sony Projector Vpl Vw1000es User Manual

							71 
Others
When a warning indicator other than the above starts flashing, and the symptom persists even after 
carrying out the above methods, consult with qualified Sony personnel. 
Warning messages
ON/STANDBY flashes in 
red. (A repetition rate of 5 
flashes)cThe lens protector is not fully open. Turn the power of the unit 
off and then on again. If the lens protector still does not fully 
open, consult with qualified Sony personnel.
Tip
In an urgent situation, refer to the illustration below to open the lens 
protector with your hands. Press the 
?/1 (ON/STANDBY) button to 
turn the power on and operate the unit.
Note
Message Lists
Message Cause and Remedy
High temp.! Lamp off in 1 
min.cTu rn  o ff th e powe r.
cCheck to ensure that nothing is blocking the ventilation holes 
(1 page 14).
Frequency is out of range!cFrequency is out of range. Input a signal that is within the 
acceptable frequency range of the unit (1 page 79).
Please replace the Lamp.cIt is time to replace the lamp. Replace the lamp (1 page 73).
cIf this message appears again after you replace the lamp, the 
lamp replacement process is not complete. Check the lamp 
replacement process (1 page 73).
To clear this message, press any button either on the remote control 
or the control panel of the unit once.
Projector temperature is 
high.  Cooling Setting 
should be “High”  if 
projector is being used at 
high altitude.cCheck to ensure that the ventilation holes on the unit are not 
covered (1 page 14).
cWhen using the unit at high altitude, set “Cooling Setting” to 
“High” (1 page 50).
When temperature inside the unit remains high, “Cooling Setting” is 
switched to “High” in 1 minute, then the fan speed increases. Symptom Cause and Remedy
Note
Note 
						

							 72
Caution messages
Message Cause and Remedy
 cNo signal is input in the selected input. Check connections 
(1 page 22).
Not applicable!cPress the appropriate button.
cThe operation to be activated by the button is currently 
prohibited.
x 
						

							73 
Others
Replacing the Lamp 
and Cleaning the 
Ventilation Holes 
(intake)
The lamp used for the light source has a 
certain lifespan. When the lamp dims, the 
color balance of the picture becomes strange, 
or “Please replace the Lamp.” appears on the 
screen, the lamp may be exhausted. Replace 
the lamp with a new one (not supplied) 
without delay.Tools you need to get started:
 Projector Lamp LMP-H330 (Optional)
 Standard Phillips screwdriver
 Cloth (for scratch protection)
 The lamp remains hot after the unit is turned 
off with the ?/1 (ON/STANDBY) button. If 
you touch the lamp, you may burn your 
fingers. When you replace the lamp, wait for 
at least 1 hour for the lamp to cool.
 Do not touch the surface of the lens. If you 
touch it, wipe off the fingerprints with a soft 
cloth.
 Pay special attention to replacing the lamp 
when the unit is installed on the ceiling.
 When replacing the lamp of a unit which is 
on the ceiling, do not stand  directly under the 
lamp cover. When removing the lamp door 
(inner cover), avoid twisting it.
If the lamp explodes, fragments may cause 
injury.
 When removing the lamp unit, make sure it 
remains horizontal, then pull straight up. Do 
not tilt the lamp unit. If you pull out the lamp 
unit while tilted and if the lamp breaks, the 
pieces may scatter, causing injury.
1Turn off the unit and unplug the 
AC power cord.
2When setting the unit on a flat 
surface such as a desk etc., put 
a cloth to prevent the surface 
from being scratched. Place the 
unit on the cloth.
Be sure that the unit is placed on a stable 
surface.
3While pressing the   part 
indicated in the lamp cover 
illustration, slide 1 and then 
open 2 the lamp cover.
4Loosen the lamp door (inner 
cover) screw with a Phillips 
screwdriver, and then open the 
lamp door.
Caution
Note 
						

							 74
5Loosen the 3 screws on the 
lamp with the Phillips 
screwdriver. Hold up the handle, 
then pull the lamp straight out.
Hold the lamp by the handle to remove and 
attach it.
6Push in the new lamp by the 
handle securely until it reaches 
the end, and then tighten the 3 
screws.
Be careful not to touch the optical block 
inside the unit.
7Close the lamp door, (inner 
cover) and then tighten the 
screw.
8Close the lamp cover.
9Wipe dust off the ventilation 
holes (intake) with a soft cloth.
Note
Handle
Note
Ventilation holes (intake) 
						

							75 
Others
10Turn on the unit, then select the 
desired setting item on the 
Setup  menu.
The menu screen below will be 
appeared.
11 Select “Yes.”
Do not put your hands into the lamp 
replacement slot, and do not allow any liquid or 
other objects into the slot to avoid electrical 
shock or fire.
 Be sure to use an LMP-H330 Projector Lamp 
for replacement. If you use lamps other than 
the LMP-H330, the unit may malfunction.
 Be sure to turn off the unit and unplug the 
power cord before replacing the lamp, then 
check the ON/STANDBY indicator has 
already been turned off.
 The unit will not turn on unless the lamp is 
securely installed in place.
 The unit will not turn on unless the lamp 
cover are securely closed.
 To cancel a message displayed on the screen, 
press either the button on the remote control 
or the one on the control panel on the unit.
Note on replacing the lamp when 
broken, in the case of a ceiling 
installation
If the lamp breaks, broken lamp pieces may 
scatter and cause injury.
When the unit is on the ceiling, remove the 
lamp door (inner cover) by sliding it 
horizontally slowly after raising it with 30 
degree opened. Avoid twisting the lamp 
door (inner cover).Disposal of the used lamp
For the customers in the USA
Lamp in this product contains mercury. 
Disposal of these materials may be 
regulated due to environmental 
considerations. For disposal or 
recycling information, please contact 
your local authorities or the 
Telecommunications Industry 
Association (www.eiae.org).
Mettre à disposition de la lampe 
usagée
Pour les clients aux États-Unis
La lampe dans ce produit contient du 
mercure. La disposition de ces 
matériaux peut être réglementée suite à 
des considérations environnementales. 
Pour obtenir des informations de 
disposition ou de recyclage, veuillez 
communiquer avec vos autorités locales 
ou la Telecommunications Industry 
Association (www.eiae.org).
Caution
Notes
Note
The lamp contains mercury. The disposal 
rules for used fluorescent tubes depend on 
where you live. Follow the waste disposal 
policy in your area.
30° 
						

							 76
Cleaning and the 
Screen of the 
Projector
Cleaning the cabinet
 To remove dust from the cabinet, wipe 
gently with a soft cloth. If dust is 
persistent, wipe with a soft cloth slightly 
moistened with a diluted mild detergent 
solution.
 Never use any type of abrasive pad, 
alkaline/acid cleaner, scouring powder, or 
volatile solvent, such as alcohol, benzene, 
thinner or insecticide. 
 Clean the unit with a cleaning cloth. 
Wiping with a dirty cloth may scratch the 
unit.
 Using such materials or maintaining 
prolonged contact with rubber or vinyl 
materials may result in damage to the 
screen surface and cabinet material.
Black points and bright points (red, 
blue, or green) on the screen
The projector is manufactured using high-
precision technology. 
You may, however, see tiny black points 
and/or bright points (red, blue, or green) that 
continuously appear on the projector.
This is a normal result of the manufacturing 
process and does not indicate a malfunction. 
						

							77 
Others
Specifications
System
Display system
SXRD panel, projection system
Display device
Size of effective display area 
0.74-inch (18.8 mm) SXRD
Number of pixels 
26,542,080 pixels (8,847,360 
pixels × 3)
Projection lens
2.1 times zoom lens (motorized) 
f=21.3 mm to 46.2 mm 
F2.9 to F3.9
Light source
Ultra High Pressure Lamp 330 W type
Screen size
60 inches to 300 inches (1,524 mm to 
7,620 mm) (measured diagonally)
Acceptable video signals
480/60i, 576/50i, 480/60p, 576/50p, 
720/60p, 720/50p, 1080/60i, 1080/50i 
The following items are available for 
HDMI input only.
1080/60p, 1080/50p, 1080/24p, 
3840 × 2160/24p, 3840 × 2160/25p, 
3840 × 2160/30p, 4096 × 2160/24p
Acceptable computer signals
fH: 19 kHz to 72 kHz 
fV: 48 Hz to 92 Hz
Maximum resolution 1,920 × 1,080 
(HDMI input only) 
For details, see “Preset Signals” (1 
page 79).
Input/Output
HDMI (2 inputs)
Digital RGB/Y PB/CB PR/CRY PB/CB PR/CRComponent: phono type
     Y with Sync: 1 Vp-p±2 dB sync 
negative (75 ohms terminated)
    P
B/CB: 0.7 Vp-p±2 dB (75 ohms 
terminated)
    P
R/CR: 0.7 Vp-p±2 dB (75 ohms 
terminated)
INPUT A
Mini D-sub 15-pin
Analog RGB:
R: 0.7 Vp-p±2 dB
(75 ohms terminated)G: 0.7 Vp-p±2 dB
(75 ohms terminated) 
G with sync/Y: 1 Vp-p±2 dB sync 
negative (75 ohms terminated) 
B: 0.7 Vp-p±2 dB 
(75 ohms terminated) 
SYNC/HD: Composite sync input: 
TTL level, positive/ negative
Horizontal sync input: TTL level, 
positive/negative
VD: Vertical sync input: TTL 
level, positive/negative
TRIGGER (2 connectors)
Minijack
DC 12 V Max. 100 mA
REMOTE
RS-232C: D-sub 9-pin (female)
LAN
RJ45, 10BASE-T/100BASE-TX
IR IN
Minijack 
3D SYNC
RJ45 connector
General
Outside dimensions (w/h/d)
520 mm × 200 mm × 640 mm 
(20 
1/2 × 7 7/8 × 25 1/4 inches) 
(without protrusions)
Mass Approx. 20 kg (44 lb 1.5 oz)
Power requirements
AC 100 V to 240 V, 4.8 A to 2.0 A,
50/60 Hz
Power consumption
480 W
Standby power requirements
3.9 W (when “Standby Mode” is set to 
“Standard”)
0.4 W (when “Standby Mode” is set to 
“Low”)
Operating temperature
5°C to 35°C (41°F to 95°F)
Operating humidity
35% to 85% (no condensation)
Storage temperature
–20°C to +60°C (–4°F to +140°F)
Storage humidity
10% to 90%
Supplied accessories
Remote control RM-PJ22 (1)
Size AA (R6) manganese batteries (2)
AC power cord for projector (1)
Plug holder (1)
AC inlet cover (1)
3D glasses (2)
Pouch for the 3D glasses (2) 
						

							 78
USB charging AC power adaptor (AC-UD10) (1)
Specifications
Input voltage: AC 100 to 240 V, 
0.2 A, 50/60 Hz
Rated output voltage: DC 5 V, 
1.5 A
Please use the above power 
requirements.
AC power cord for USB charging AC power 
adaptor (1)
For the customers in the 
U.S.A. and Canada
WARNING:
Using this unit at a voltage other 
than 120 V may require the use 
of a different line cord or 
attachment plug, or both. To 
reduce the risk of fire or electric 
shock, refer servicing to 
qualified service personnel.
USB charging cable (GPHK05 - 
2010 - 0007/SONY) (1.2 m) (1)
Câble de charge USB (GPHK05 - 2010 - 0007/
SONY) (1,2 m) (1)
CD-ROM (ImageDirector3) (1)
Operating Instructions (1)Optional accessories
Projector Lamp 
LMP-H330 (for replacement)
Projector Suspension Support 
PSS-H10
3D glasses
TDG-PJ1
3D Sync Transmitter
TMR-PJ1
 Not all optional accessories are available in 
all countries and area. Please check with your 
local Sony Authorized Dealer.
 Information on accessories in this manual is 
current as of December 2011.
Design and specifications are subject to change 
without notice.
The values for mass and dimensions are 
approximate.
Warning on power connection
Use a proper power cord for your local power supply.
* Use a rated plug that complies with the regulation of each country/region and the specifications.
Note
Notes
Note
The United States, 
CanadaContinental 
EuropeUK, Ireland, 
Australia, 
New ZealandJapan China
Plug type YP-3 YP-12A * YP-359 VM0722
Female end YC-13 YC-13D VM0303B YC-13 VM0724
Cord type SVT H05VV-F CEE (13) 
53 rd (OC)VCTF 227 IEC 
53(RVV)
Rated Voltage 
& Current10A/125V 10A/250V 10A/250V 12A/125V 10A/250V
Safety approval UL/CSA VDE VDE
DENANHOCCC 
						

							79 
Others
The following table shows the signals and video formats which you can project using this 
unit.
When a signal other than the preset signal shown below is input, the picture may not be 
displayed properly.
Preset Signals
Memory 
No.Preset signal
(resolution)fH
(kHz)fV
(Hz)Sync H Size
3 480/60i 480/60i 
(720 × 480i)15.734 59.940 SonG/Y –
4 576/50i 576/50i 
(720 × 576i)15.625 50.000 SonG/Y –
5 480/60p 480/60p 
(Progressive 
NTSC)
(720 × 480p) 31.470 60.000 SonG/Y –
6 576/50p 576/50p 
(Progressive 
PA L )
(720 × 576p)31.250 50.000 SonG/Y –
7 1080/60i 1035/60i 
(1920 × 1035i) 
1080/60i 
(1920 × 1080i)33.750 60.000 SonG/Y –
8 1080/50i 1080/50i 
(1920 × 1080i)28.130 50.000 SonG/Y –
10 720/60p 720/60p 
(1280 × 720p)45.000 60.000 SonG/Y –
11 720/50p 720/50p 
(1280 × 720p)37.500 50.000 SonG/Y –
12 1080/60p 1080/60p 
(1920 × 1080p)67.500 60.000 – –
13 1080/50p 1080/50p 
(1920 × 1080p)56.260 50.000 – –
14 1080/24p 1080/24p 
(1920 × 1080p)26.973 23.976 – –
18 720/60p
(Frame packing)720/60p
(1280 × 720p)90.000 60.000 – –
19 720/50p
(Frame packing)720/50p
(1280 × 720p)75.000 50.000 – –
20 1080/24p
(Frame packing)1080/24p
(1920 × 1080p)53.946 23.976 – – 
						

							 80
26 640 × 480 VESA 60 31.469 59.940 H-neg, V-neg 800
28 VESA 72 37.861 72.809 H-neg, V-neg 832
29 VESA 75 
(IBM M3)37.500 75.000 H-neg, V-neg 840
30 VESA 85 
(IBM M4)43.269 85.008 H-neg, V-neg 832
31 800 × 600 VESA 56 35.156 56.250 H-pos, V-pos 1024
32 VESA 60 37.879 60.317 H-pos, V-pos 1056
33 VESA 72 48.077 72.188 H-pos, V-pos 1040
34 VESA 75 
(IBM M5)46.875 75.000 H-pos, V-pos 1056
35 VESA 85 53.674 85.061 H-pos, V-pos 1048
37 1024 × 768 VESA 60 48.363 60.004 H-neg, V-neg 1344
38 VESA 70 56.476 70.069 H-neg, V-neg 1328
39 VESA 75 60.023 75.029 H-pos, V-pos 1312
45 1280 × 960 VESA 60 60.000 60.000 H-pos, V-pos 1800
47 1280 × 1024 VESA 60 63.974 60.013 H-pos, V-pos 1696
50 1400 × 1050 SXGA + 65.317 59.978 H-neg, V-pos 1864
55 1280 × 768 1280 × 768/60 47.776 59.870 H-neg, V-pos 1664
56 1280 × 720 1280 × 720/60 44.772 59.855 H-neg, V-pos 1664
93 3840 × 2160/24p 3840 × 2160/24p
(3840 × 2160)53.946 23.976 – –
94 3840 × 2160/25p 3840 × 2160/25p
(3840 × 2160)56.25 25 – –
95 3840 × 2160/30p 3840 × 2160/30p
(3840 × 2160)67.4325 29.97 – –
96 4096 × 2160/24p 4096 × 2160/24p
(4096 × 2160)54 24 – – Memory 
No.Preset signal
(resolution)fH
(kHz)fV
(Hz)Sync H Size