Sony Projector Vpl Vw1000es User Manual

							
21 
Connections and Preparations
The range to move the picture projected on the screen can be adjusted only within the octagon area 
illustrated below. For details, see “Projection Distance and Lens Shift Range” (1 page 86).
To adjust the tilt of the installation surface
If the unit is installed on an uneven surface, use the adjusters to keep the unit level.
 If the unit is tilted up or down, the projected image may be trapezoidal.
 Be careful not to catch your finger when turning the adjusters.
Lens adjustment window (test pattern)
Note
Notes
Range of movement of 
the projected picture
Projected Picture
H: Width of the projected picture
V: Height of the projected picture
0.8V
0.8V
0.31H 0.31H
Adjusters
Turn to adjust.
The dashed lines show the screen sizes of 
each aspect ratio.
1.33:1 (4:3)
2.35:1 1.85:1
1.78:1 (16:9) 
						

							 22
Preparation 3: Connecting the Unit
When making connections, be sure to do the following:
 Turn off all equipment before making any connections.
 Use the proper cables for each connection.
 Insert the cable plugs properly; poor connection at the plugs may cause a malfunction or 
poor picture quality. When pulling out a cable, be sure to pull it out from the plug, not 
the cable itself.
 Refer to the operating instructions of the connected equipment.
To connect to equipment with HDMI output connectors
You can enjoy better picture quality by connecting a DVD player/recorder, Blu-ray Disc 
player/recorder, or PS3® equipped with HDMI output to the HDMI input of the unit. 
Moreover, if you have a Control for HDMI compatible equipment, you can operate the 
unit synchronizing with the Control for HDMI compatible equipment. For details, see 
“HDMI Setting” of the Function   menu (1 page 53) and “About the Control for 
HDMI” (1 page 65).
 
Connecting to a VCR
HDMI cable (not supplied)
: Video signal flow Right side of the unit
Equipment with HDMI output 
connectors
to HDMI output AV amplifier
Speakers
When using an optional HDMI cable, be sure to use a Sony 
HDMI cable or other cable that has the HDMI logo. 
						

							23 
Connections and Preparations
 Use a high-speed HDMI cable. With a standard HDMI cable, images of 1080p, DeepColor, 3D 
video and 4K video may not be displayed properly.
 When connecting an HDMI cable to the unit, make sure the 
V mark on the upper part of the HDMI 
input of the unit and the v mark on the connector of the cable is set at the same position.
 If the picture from equipment connected to the unit with an HDMI cable is not correct, check the 
settings of the connected equipment.
To connect to equipment with component video output 
connectors
Notes
Component video cable (not supplied)
: Video signal flowEquipment with component 
video output connectors Right side of the unitAV amplifierSpeakers 
						

							 24
 
 Use a high-speed HDMI cable. With a standard HDMI cable, images of 1080p video may not be 
displayed properly.
 When connecting an HDMI cable, make sure the 
V mark on the upper part of the HDMI input of 
the unit and the 
v mark on the connector of the cable is set at the same position.
 If you set your computer, such as a notebook type, to output the signal to both computer’s display 
and this equipment, the picture of the equipment may not appear properly. Set your computer to 
output the signal to only the external monitor.
For details, refer to the computer’s operating instructions supplied with your computer. For 
settings of the computer, consult with the manufacturer of the computer.
 If the picture from equipment connected to the unit with an HDMI cable is not correct, check the 
settings of the connected equipment.
Connecting to a Computer
Notes
HD-Dsub15 pin cable (not supplied) or HDMI cable (not supplied)
: Video signal flow Right side of the unit
to monitor outputComputer
When using an optional HDMI cable, be sure to use a Sony 
HDMI cable or other cable that has the HDMI logo. 
						

							25 
Connections and PreparationsThis unit incorporates a 3D Sync Transmitter. Depending on the installation environment 
of the unit, the 3D glasses may not receive 3D signals properly from the unit’s built-in 3D 
Sync Transmitter. In this case, connect an optional TMR-PJ1 3D Sync Transmitter and 
place it near your viewing position.
Tip
Place the optional TMR-PJ1 3D Sync Transmitter directly facing the 3D glasses. Also, in order to 
stabilize operation of the 3D glasses, it is recommended that you place the 3D Sync Transmitter near 
your viewing position.
CAUTION
Be sure to use straight-type LAN cable of up to 15 m labeled TYPE CM, and do not use 
an extension cord.
 
 The 3D SYNC connector is dedicated for the optional 3D Sync Transmitter. Do not connect 
computers or other network devices, to avoid malfunction.
 Be sure to use straight-type LAN cable (not supplied) labeled Cat-7 (Category 7). If you use other 
than the specified cable, the 3D Sync Transmitter may occasionally not work.
 Be sure to use cable of up to 15 m, and do not use an extension cord. Also, keep the LAN cable 
away from any AC power cords as much as possible.
 Only one TMR-PJ1 can be connected to the unit. Never connect multiple TMR-PJ1 units, which 
may cause a malfunction.
 When connected to the TMR-PJ1, the built-in 3D Sync Transmitter feature of the unit will turn off. 
You cannot use both at the same time.
Connecting to a 3D Sync Transmitter
Notes
Right side of the unit
TMR-PJ1 3D Sync Transmitter 
(not supplied)
LAN cable (not supplied)
: 3D sync signal flow2 m
(6.6 ft) 
						

							 26
Preparation 4: 
Selecting the Menu 
Language
You can select one of 16 languages for 
displaying the menu and other on-screen 
displays. The factory default setting is 
English. To change the current menu 
language, set the desired language with the 
menu screen.
1Press MENU.
The menu appears.
2Press M/m to select the Setup 
 menu, and press , or  .
The setting items of the selected menu 
appear.
3Press M/m to select “Language,” 
and press , or  .
4Press M/m/
						

							27 
Projecting
This section describes how to operate the unit to view the picture from the equipment 
connected to the unit. It also describes how to adjust the quality of the picture to suit your 
taste.
Projecting the 
Picture
1Power on both the unit and the 
equipment connected to the 
unit.
2Press INPUT to display the input 
palette on the screen.
3Select the equipment from 
which you want to display 
images.
Press INPUT repeatedly or press M/m/
 (enter) to select the equipment from 
which to project.
Tips
 When “Auto Input Search” is set to “On” on 
the Function   menu, only input terminals 
with effective signals are displayed in the 
input palette.
 When “Status” is set to “Off” on the Setup 
 menu, the input palette does not appear. 
Press the INPUT button to switch between 
input terminals in sequence.
 When the “Control for HDMI” is set to “On” 
on the Function   menu, the input terminal 
with effective signals is automatically 
displayed, synchronizing with the operation 
of the equipment connected to HDMI 1 or 
HDMI 2 input of the unit. (Only when the 
connected equipment supports Control for 
HDMI compatible.)
Projecting
Example:To view the picture from 
the video equipment 
connected to the HDMI 1 
connector of this unit.
To view the picture from Press INPUT 
to display
RGB equipment connected 
to the INPUT A connectorInput-A
Component equipment 
connected to the Y P
B/CB 
PR/CR connectorComponent
Equipment connected to the 
HDMI 1 connectorHDMI 1
Equipment connected to the 
HDMI 2 connectorHDMI 2 
						

							 28
1Press the ?/1 (ON/STANDBY) 
button.
A message “POWER OFF?” appears on 
the screen.
2Press the ?/1 (ON/STANDBY) 
button again before the 
message disappears.
The lens protector will close. Be careful 
not to catch your fingers or any objects. 
The ON/STANDBY indicator flashes in 
green and the fan continues to run to 
reduce the internal heat. First, the ON/
STANDBY indicator flashes quickly, 
during which you will not be able to 
light up the ON/STANDBY indicator 
with the ?/1 (ON/STANDBY) button. 
The fan stops and the ON/STANDBY 
indicator changes from flashing green to 
remaining red.
The power is turned off completely, and 
you can disconnect the AC power cord.
Never disconnect the AC power cord while 
the indicator is flashing.
You can turn off the unit by holding the ?/1 
(ON/STANDBY) button for about 1 second, 
instead of performing the above steps.
Watching 3D Video 
Images
You can enjoy powerful 3D video images, 
such as from 3D games and 3D Blu-ray 
Discs, using the supplied 3D glasses.
1Turn on the HDMI equipment for 
3D compatibility connected to 
the unit, then play the 3D 
content.
For details on how to play 3D content, 
refer to the operating instructions for the 
connected equipment.
2Turn on the unit and project the 
3D video image onto the screen.
For details on how to project the image, 
see “Projecting the Picture”  (1 page 
27).
3Turn on the 3D glasses, and 
then put them on so that they fit 
comfortably.
For details on how to use the 3D glasses, 
see “Using the 3D Glasses”  (1 page 
29).
Tips
 The factory default setting for ”2D-3D 
Display Sel.” is “Auto” to allow projecting 
3D video images automatically when the unit 
detects 3D signals.
 To convert 3D video images to 2D video 
images, set “2D-3D Display Sel.” to “2D” 
(1 page 52).
 It may not be possible to display 3D video 
image, depending on the type of signal. Set 
the “2D-3D Display Sel.” to “3D,” and “3D 
Format” to “Side-by-Side” or “Over-Under” 
to suit the format of the 3D content you want 
to watch (1 page 52).
 Use the 3D glasses within the 
communication range (1 page 30).
Turning Off the Power
Note
Notes 
						

							29 
Projecting
 You can watch 3D video images only when 
signals from HDMI input. When connecting 
3D equipment such as a 3D game or 3D Blu-
ray Disc player to the unit, use an HDMI 
cable.
 There are differences in perception of 3D 
video images among individuals.
 When the temperature of the usage 
environment is low, the 3D effect may be 
diminished.
Adjusting/Setting the 3D 
functions
You can adjust/set the 3D functions by 
pressing the 3D button on the remote control 
or with the “3D Settings” of the Function   
menu. For details, see “3D Settings” (1 
page 52).
The 3D glasses receive signals from the 3D 
Sync Transmitter built into the front of the 
unit, which are reflected to the glasses from 
the screen. When watching 3D video images 
using the 3D glasses, face squarely toward 
the screen.
1Press the power button on the 
3D glasses. 
The LED indicator lights up in green.
2Put on the 3D glasses.
3Turn toward the screen.
Precautions for use
The 3D glasses receive infrared signals sent 
by the 3D Sync Transmitter built into the 
front of the unit, which are reflected to the 
glasses from the screen.
Misoperation may occur if:
– The 3D glasses do not face the screen
– There are objects blocking the path 
between the 3D glasses and the screen
– The viewing position is too far from the 
screen or the distance between the unit and 
screen is too great
– There are other infrared communication 
devices nearby
Using the 3D Glasses
LED indicator Power button
IR sensor 
						

							 30
3D glasses communication range
Figures A and B below indicate the communication range of the 3D glasses. If you try to 
watch 3D video images from a distance greater than the communication range or install 
the unit outside the communication range, the 3D glasses may not be able to display the 
images properly. Also, the viable angles and distance vary depending on the screen type, 
environment of the room, and installation environment of the unit.
Figure A: 3D sync signal communication distance (Shift Range: 0.5 V)
Figure B: 3D glasses communication range (The figure shows the distance 
between the screen and the projector as 8 m.)
Screena
Projector
Side view
3D glasses b
a + b = 13 m (Maximum)
Screen3D glasses
Top or side view
Approx. 5 m (Maximum)