Sony Projector Vpl Vw1000es User Manual

31 
Projecting
Use the provided USB charging AC power 
adaptor to charge your 3D glasses.
Connect the USB charging cable supplied 
with the unit, to the supplied USB charging 
AC power adaptor only. 
Using any other connector may cause fire, a 
rise in temperature or damage to the cable 
and glasses.
1Turn off the power of the 3D 
glasses.
2Open the 3D glasses cover and 
connect the USB charging cable 
supplied with the unit.
3Connect the USB cable to the 
USB connector of the supplied 
USB charging AC...

 32
Cleaning
 Clean the unit with a soft, dry cloth. If the 
unit is very dirty, wipe it off with a soft 
cloth lightly moistened with a mild 
detergent solution, and then wipe with a 
soft dry cloth.
 Do not use any type of solvent such as 
alcohol, thinner, or benzine as it may 
damage the finish of the cabinet.
 If you use any chemical cleaner, observe 
the instructions provided with the product.
 If the cabinet of the unit is splashed with 
any type of solvent such as insecticide, or 
remains in...

33 
Projecting
Image of the lens moving
In the example below, the images with 
aspect ratio of 1.78:1 (16:9) and 2.35:1 are 
projected on a 2.35:1 screen.
 After you have selected and confirmed the 
lens position, the lens starts to move. Do not 
touch, or place anything near, the lens, 
otherwise it may cause injury or a 
malfunction.
 If you press any button on the unit while the 
lens is moving, the lens stops. In this case, 
select the lens position again or adjust the 
lens manually.
 The Picture...

 34
Selecting the Aspect Ratio According to the 
Video Signal
You can select an aspect ratio best suited for the video signal received.
Press ASPECT.
Each time you press the button, you can 
select the “Aspect” setting.
You can also select it using the menu 
(1 page 48).
Original image Recommended setting and resultant images
ASPECT 
button
1.85:1
Squeezed 1.85:1
1.85:1 Zoom
2.35:1
Squeezed 2.35:1
2.35:1 Zoom 

35 
Projecting
Original image Recommended setting and resultant images
1.78:1 (16:9)
1.33:1 (4:3)
1.33:1 (4:3) with side panels
Normal
Squeezed
Stretch
2.35:1
V Stretch
When using an anamorphic lens 

 36
 Selectable aspect modes vary depending on the input signal.
 The aspect cannot be selected for an input signal from a computer, or when preset memory number 96 ( 1 page 80) signal is input.
Notes on switching the “Aspect” setting
 Select the aspect mode taking into account that changing the aspect ratio of the original 
picture will provide a different look from that of the original image.
 Note that if the unit is used for profit or for public viewing, modifying the original  picture by switching...

37 
Projecting
Selecting the Picture Viewing Mode
You can select the picture viewing mode that best suits the type of video source or room 
conditions.
You can save and use different preset modes for 2D/3D respectively.
Press one of the CALIBRATED PRESET buttons.
Setting items Description
CINEMA FILM 1 Picture quality suited to reproducing the highly dynamic and clear images 
typical of master positive film.
CINEMA FILM 2 Picture quality suited to reproducing the rich tone and color typical of a 
movie...

 38
Using the Supplied Software to Adjust the 
Picture Quality (ImageDirector3)
By using the “ImageDirector3” (supplied as a CD-ROM), you can make the desired 
gamma correction from a computer connected to the unit. Connect the REMOTE 
connector of the unit with a computer and start-up “ImageDirector3” on the computer.
For details on how to use the “ImageDirector3,” refer to the Help within the CD-ROM.
 You need to install the “ImageDirector3” on a computer beforehand.
 When connecting the REMOTE...

39 
Using the Menus
 
This section describes how to make various adjustments and settings using the menus.
Operation through 
the Menus
The unit is equipped with an on-screen menu 
for making various adjustments and settings. 
If you select an item name followed by an 
arrow (B), the next menu window with 
setting items appears.
1Press MENU.
The menu window appears.
2Press M/m to select a menu item, 
and press , or  .
The items that can be set or adjusted 
with the selected menu appear. The item...

 40
4Make the setting or adjustment 
of an item.
When changing the adjustment 
level
To increase the value, press M/,.
To decrease the value, press m/