Sony Projector Vpl Vw1000es User Manual

11 
Connections and PreparationsThis section describes how to install the unit and screen, how to connect the equipment 
from which you want to project the picture, etc.
Unpacking
Check the carton to make sure it contains the 
following items:
 Remote control (1) 
 Size AA (R6) manganese batteries (2)
 AC power cord for the projector (1)

 AC inlet cover (1)

 Pouch for the 3D glasses (2)
 USB charging AC power adaptor (1)
 AC power cord for USB charging AC 
power adaptor (1)
 USB charging cable (GPHK05...

 12
VORSICHT
Explosionsgefahr bei Verwendung falscher 
Batterien. Batterien nur durch den vom 
Hersteller empfohlenen oder einen 
gleichwertigen Typ ersetzen.
Wenn Sie die Batterie entsorgen, müssen Sie 
die Gesetze der jeweiligen Region und des 
jeweiligen Landes befolgen.
Installing batteries
Two size AA (R6) batteries are supplied for 
Remote Control.
To avoid risk of explosion, use size AA (R6) 
manganese or alkaline batteries.
Caution about handling the remote 
control
 Handle the remote control...

13 
Connections and Preparations
Preparation 1: Installing the Unit
The lens shift allows you to have broader options for placing the unit and viewing pictures 
easily.
Unsuitable installation
Do not place the unit in the following 
situations, which may cause malfunction or 
damage to the unit.
Near walls
To maintain the performance and reliability 
of the unit, leave space between walls and 
the unit as illustrated.
Leave a space of at least 5 cm (2 inches) 
between the wall and the exhaust port side...

 14
Do not do any of the following while using 
the unit.
Blocking the ventilation holes (intake 
or exhaust)
For details on the location of the ventilation 
holes (intake or exhaust), see “Location of 
Controls” on page 8.
Tilting front/rear and left/right
Avoid using the unit tilted at an angle of 
more than 15 degrees.
Do not install the unit anywhere other than 
on a level surface or on the ceiling. Installing 
the unit in such a location may result in 
uneven color uniformity or reduce the...

15 
Connections and Preparations
WARNING
When installing the unit, incorporate a readily 
accessible disconnect device in the fixed 
wiring, or connect the power plug to an easily 
accessible socket-outlet near the unit. If a fault 
should occur during operation of the unit, 
operate the disconnect device to switch the 
power supply off, or disconnect the power 
plug.
AVERTISSEMENT
Lors de l’installation de l’appareil, incorporer 
un dispositif de coupure dans le câblage fixe ou 
brancher la fiche...

 16
The installation distance between the unit and a screen varies depending on the size of the 
screen or whether or not you use the lens shift features. Install this unit so that it fits the 
size of your screen. For details on the distance between the unit and the screen (the 
projection distance) and the size of projected video, see “Projection Distance and Lens 
Shift Range” (1 page 86).
1Position the unit so that the lens is parallel to the screen.
2Project an image on the screen and adjust the...

17 
Connections and Preparations
Preparation 2: Adjusting the Picture Position
Project an image on the screen and then adjust the picture position.
Tips
 The 
?/1 (ON/STANDBY), INPUT, MENU, and M/m/

 18
1After connecting the AC power 
cord to the unit, plug the AC 
power cord into a wall outlet.
The ON/STANDBY indicator lights in 
red and the unit goes into standby mode.
2Press the ?/1 (ON/STANDBY) 
button to turn on the unit. 
The lens protector will open.
The ON/STANDBY indicator flashes in 
green, and then lights in green.
3Adjust the focus.
Press the LENS ADJUSTMENT 
(FOCUS) button to display the Lens 
Focus adjustment window (test pattern). 
Then adjust the focus of the picture by 
pressing the...

19 
Connections and Preparations
5Adjust the picture position.
Press the LENS ADJUSTMENT 
(SHIFT) button to display the Lens Shift 
adjustment window (test pattern). Then 
adjust to the proper position of the 
picture by pressing the M/m/

 20
To adjust the horizontal position
Press