Sony Dav Dz610 Operating Instructions

							21GB
Getting Started
Step 1: Installing the System
Install the system by referring to the illustration below.
To attach the foot pads to the subwoofer
Note Use caution when placing the speakers and/or speaker stands attached to the speakers on a specially treated (waxed, 
oiled, polished, etc.) floor, as staining or discoloration may result.
For assembling the speakers refer to “Speaker Installation Guide” (supplement).
Getting Started
How to position the system
Assembling the speakers
AB
DEF
C
G
A Front speaker (L (left))
B Front speaker (R (right))
C Center speaker
D Surround speaker (L (left))
E Surround speaker (R (right))
F Subwoofer
G Unit
,
Remove the foot pads from 
the protective cover.
 
						

							22GB
Getting Started
Caution
 Contact a screw shop or installer for information regarding the wall material or screws to be used.
 Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach 
the screws securely to a beam. Install the speakers on a vertical and flat wall where reinforcement is applied.
 Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength or 
improper screw installation, natural calamity, etc.
To hang the speaker on a wall
1Connect the speaker cord with the color tube to 3, and the speaker cord without the 
color tube to #.
2Prepare screws (not supplied) that are suitable for the hole on the back of each speaker. 
See the illustrations below.
When installing the speakers on a wall
Color tube
Front left speaker (L): White
Front right speaker (R): Red
Center speaker: Green
Surround left speaker (L): Blue
Surround right speaker (R): Gray
30 mm (1 3/16 inches)4 mm (
3/16 inch)Hole on the back of 
the speaker
5 mm 
(
7/32 inch)
10 mm
(
13/32 inch)
 
						

							23GB
Getting Started
3Fasten the screws to the wall, then hang the speaker on the wall.
8 to 10 mm
(11/32 to 13/32 inch)
Depth of fastened screw
145 mm
(5 3/4 inches) For the center speaker
101.6 mm
 (4 inches) For the tall speakers (DAV-DZ610 only)
For the small speakers
 
						

							24GB
Getting Started
Step 2: Connecting the System
1Insert the connectors of the speaker cords to match the color of the SPEAKERS jacks 
of the unit until they click.
2Connect the speaker cord with the color tube to 3, and the speaker cord without the 
color tube to #.
The subwoofer speaker cord is fixed to the subwoofer.
Note Do not catch the speaker cord insulation (rubber covering) in the speaker terminals.
Connecting the speakers
CENTERSUBWOOFERFRONT  L FRONT  RS
P
E
A
K
E
R
S
SUR  RSUR  LS
P
E
A
K
E
R
S
Green
(Center speaker)
Purple 
(Subwoofer)
White 
(Front left speaker (L)) Red 
(Front right speaker (R))Gray 
(Surround right speaker (R))
Blue 
(Surround left speaker (L))
Color tube
(–)(+)Rear of the speaker
Connector
 
						

							25GB
Getting Started
1 Connecting the video to your TV
Depending on the jacks on your TV, select one of the connection methods.
xMethod 1: Video cord (supplied) connection
This is the basic connection.
xMethod 2: HDMI cable* connection
Picture quality will be improved compared to Method 1.
If your TV is compatible with the Audio Return Channel function, this connection also sends a digital 
audio signal from the TV. You do not need to make a separate audio connection for listening to TV 
sound. For details of the Audio Return Channel function, see “Receiving the digital audio signal of your 
TV” (page 54).
xMethod 3: Component video cable connection (not supplied)
Picture quality will be improved compared to Method 1.
Connecting your TV/set-top box
When connecting to a TV only
1 Video2 Audio1 Video2 Audio When connecting to a TV and set-top box
Video
VIDEO IN
COMPONENT VIDEO INPB/CBPR/CRYHDMI IN
PB/CBPR/CRYVIDEO
OUT
COMPONENT VIDEO 
OUT
O
U
TA
R
C
Method 2 
(not supplied)Method 3 
(not supplied)Method 1 
(supplied)
 
						

							26GB
Getting Started
2 Connecting the audio from your TV/set-top box
To listen to TV or set-top box sound via the system, select one of the connection methods.
xMethod 1: Audio cord (not supplied) connection
This is the basic connection and sends an analog audio signal.
xMethod 2: Digital optical cord (not supplied) connection (DAV-DZ610 only)
Sound quality will be improved compared to Method 1.
Note The system can accept both digital and analog signals. Digital signals have priority over analog signals. If the digital 
signal ceases, the analog signal will be processed after a few seconds.
Tip
 You can connect another component, such as a VCR, digital satellite receiver, or PlayStation, to the TV jacks 
instead of your TV.
DIGITAL OUTOPTICAL
AUDIO OUTR
L
DIGITAL
IN
OPTICAL
TV
A
U
D
IO
 INL RTV
Method 2 
(not supplied)Method 1 
(not supplied)
 
						

							27GB
Getting Started
To change the color system (PAL or NTSC) (Asian, Australian, Middle 
Eastern, and South African models only)
Depending on your TV, you may be required to select either PAL or NTSC for the color system.
The initial setting for Australian, Middle Eastern, and South African models is PAL.
The initial setting for Asian models is NTSC.
1Turn off the system by pressing "/1.
2Turn on the system by pressing "/1 on the unit while pressing FUNCTION on the unit.
Each time you perform this operation, the color system toggles between PAL and NTSC.
“NTSC” lights up in the front panel display when the color system is set to NTSC.
You can enjoy connected components via the system’s speakers.
Connecting the other components
Connected component Required cord for connection
Portable audio source (not supplied)A Stereo mini-plug cord (not supplied)
USB device (not supplied)
B USB connector (not supplied)
AB
To a portable audio source.
 
						

							28GB
Getting Started
Note After connecting the FM wire antenna (aerial), extend and keep it as horizontal as possible.
1Connect the AC power cord (mains lead).
The demonstration appears in the front panel display.
2Press "/1 to turn the system on, then press "/1 again to turn off the demonstration.
Connecting the antenna (aerial)
Connecting the AC power cord (mains lead)
C
O
A
X
IA
L
 7
5
F
M
ANTENNA
or
FM wire antenna (aerial)
(supplied)
Wall outlet (mains): The shape of 
the wall outlet (mains) differs 
depending on the area.
"/1
 
						

							29GB
Getting StartedStep 3: Setting up the 
System
Displayed items vary depending on the area.
1Turn on your TV.
2Switch the input selector on your TV so 
that the signal from the system 
appears on the TV screen.
3Press "/1 to turn the system on.
4Press   without inserting a disc or 
connecting a USB device.
Note If this message does not appear, press 
FUNCTION repeatedly to select “DVD/CD.” If this message still does not appear, recall the 
Quick Setup display (page 60).
5Press X/x to select a language, then 
press .
6Press X/x to select the setting that 
matches your TV type, then press  .
 [16:9]: This aspect ratio is for a wide-
screen TV or a 4:3 standard TV with a 
wide-screen mode (page 62)
 [4:3 LETTER BOX] or [4:3 PAN SCAN]: 
This aspect ratio is for a 4:3 standard TV 
(page 62)
7Press X/x to select the Control for 
HDMI setting, then press  .
 [ON]: The Control for HDMI function is 
set to on.
 [OFF]: The Control for HDMI function is 
set to off.
Performing the Quick Setup
"/1
 
DISPLAY
C/X/x/c, 
Home Theatre System
Press            to run QUICK SETUP.
Press            to erase this message.ENTERCLEAR
LANGUAGE SETUP
MENU: OSD:
AUDIO:
SUBTITLE:ENGLISHENGLISH
FRENCH
SPANISH
PORTUGUESE
VIDEO SETUP
PROGRESSIVE (COMPONENT OUT): TV TYPE:
4:3 OUTPUT:
COLOR SYSTEM 
(VIDEO CD):16:9
AUTO
PAUSE MODE:
16:9
4:3 LETTER BOX
4:3 PAN SCAN
HDMI SETUP
HDMI RESOLUTION:
AUDIO RETURN CHANNEL: VOLUME LIMIT:AUTO(1920x1080p)
OFF
SD    YCBCR/RGB(HDMI):
JPEG RESOLUTION: AUDIO(HDMI):
CONTROL FOR HDMI:ON
YC
BCR
ON
OFF
 
						

							30GB
Getting Started
8Press C/c to select the speaker 
formation image as the speakers are 
actually positioned, then press  .
 [STANDARD]: Select this when you 
install all the speakers normally.
 [NO CENTER]: Select this when you 
install the front and surround speakers 
only.
 [NO SURROUND]: Select this when you 
install the center and front speakers only.
 [FRONT ONLY]: Select this when you 
install the front speakers only.
 [ALL FRONT]: Select this when you 
install all the speakers in front of the 
listening position.
 [ALL FRONT - NO CENTER]: Select 
this when you install the front and 
surround speakers in front of the listening 
position.
9Connect the calibration mic (supplied) 
to the A.CAL MIC jack on the front 
panel.
Set up the calibration mic at ear level using 
a tripod, etc. (not supplied).
The front of each speaker should face the 
calibration mic, and there should be no 
obstruction between the speakers and the 
calibration mic.
10Press C/c to select [YES], then press 
.
Be quiet during the measurement.
Note Loud test sounds are output when [AUTO 
CALIBRATION] starts. You cannot turn the 
volume down. Give consideration to children 
and neighbors.
 The environment of the room in which the 
system is installed may affect measurements. 
When the measurements differ considerably 
from the status of the speaker installation, 
perform the speaker settings manually by 
following “Settings for the speakers” (page 67). 
SPEAKER FORMATION
STANDARD
Calibration mic