Sony Bdv It1000 Operating Instructions

21GB
Getting Started
3Secure the speaker cord by running it through the slot, then attach the cover to the 
speaker.
4Attach the baffle cover to the speaker.
Use the baffle cover (short). Press the ends of the baffle cover over the pin, then press down to 
flush fit the speaker front.
Center speaker
Cover
,
Speaker cordsSlot
Baffle cover (short)
,
 

22GB
Getting Started
5Attach the grille to the speaker.
Be careful with the orientation of the grille. The SONY logo should be at the left side of the 
grille.
Note When assembling, take care not to touch the speaker unit.
 Be sure to use the speakers with their grilles attached.
 Do not push on the attached grille. It may cause damage to the speaker unit.
6Attach the foot pads to the bottom of the speaker.
Attach the foot pads (thick) to the front of the speaker and the foot pads (thin) to the rear so...

23GB
Getting Started1Attach the pole to the floor base.
When attaching, match the orientation of the protruding parts of the pole and the base.
Secure the pole to the floor base with two long black screws (supplied).
2Thread the speaker cord through the hole in the bottom of the floor base and pull the 
cord out from the top of the pole.
Twist the split ends of the speaker cord together before you thread the cord.
Assembling the front and surround speakers with the speaker stands
,
Pole
Front
FrontLong...

24GB
Getting Started
3Remove the screw from the speaker.
The removed screw is used to attach the speaker to the pole, so be careful not to lose it.
Note When assembling, take care not to touch the speaker unit.
Front speaker
Surround speaker Screw
 

25GB
Getting Started
4Connect the speaker cords to the speaker.
The connector and color tube of the speaker cords are the same color as the label of the jacks to be 
connected.
Use the speaker cords as follows:
 Front left speaker (L): White
 Front right speaker (R): Red
 Surround left speaker (L): Blue
 Surround right speaker (R): Gray
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord 
with the color tube to 3, and the speaker cord without the color tube...

26GB
Getting Started
5Attach the speaker to the pole.
When attaching, match the orientation of the pole and speaker.
Secure the speaker with the screw removed in Step 3.
Note When assembling, take care not to touch the speaker unit.
6Take up the slack in the speaker cord by pulling from the bottom of the floor base and 
secure it by running through the cord retainers.
,
Front speaker Surround speaker
Adjust the length of the cord.Screw ScrewFront speaker Surround speaker
Speaker cord
Bottom of the floor...

27GB
Getting Started
7Attach the baffle cover to the speaker.
Use the baffle cover (short) for the front speaker, baffle cover (long) for the surround speaker.
Press the ends of the baffle cover over the pin(s), then press down to flush fit the speaker front.
Front speaker
Baffle cover (short)Surround speaker
“J” mark
Baffle cover (long)
 

28GB
Getting Started
8Attach the grille to the speaker.
Be careful with the orientation of the grille. The SONY logo should be at the bottom of the grille.
Note When assembling, take care not to touch the speaker unit.
 Be sure to use the speakers with their grilles attached.
 Do not push on the attached grille. It may cause damage to the speaker unit.
GrilleFront speaker Surround speaker
Grille
 

29GB
Getting Started
Fully-assembled illustration with the speaker stands
Surround left speaker (L): 
Blue labelSurround right speaker (R): 
Gray label Front left speaker (L): 
White labelFront right speaker (R): 
Red label
White Red Blue Gray
Green
Center speaker: Green label
 

30GB
Getting Started
Note When moving the speakers, hold the floor base and the pole (1), not the speaker part (2).