Sony Bdv It1000 Operating Instructions

11GB
BDV-IT1000
BDV-IS1000
ALAN (100) terminal (65)
BCOMPONENT VIDEO IN (SAT/CABLE) 
jacks (59)
CCOMPONENT VIDEO OUT jacks (57)
DVIDEO OUT (VIDEO, S VIDEO) jacks 
(57)
EHDMI IN1/2 jacks (59)
FIR REMOTE (IN, OUT) (16) 
(BDV-IT1000 only)
GDIGITAL IN (TV OPTICAL) jack (57)
HDIGITAL IN (SAT/CABLE OPTICAL, 
COAXIAL) jacks (59)
IEZW-RT10 slot (63)JAM terminal (62)
KFM 75Ω COAXIAL jack (62)
LHDMI OUT jack (57)
MDMPORT (DIGITAL MEDIA PORT) jack 
(59)
NA.CAL MIC jack (69, 108)
OSAT/CABLE IN (VIDEO, AUDIO R/L)...

12GB
APHONES jack (67)
BPOWER (ON/OFF) (67, 102)
CPOWER / ON LINE indicator (67, 99)
DPAIRING indicator (102)
EPAIRING (102)FWireless transceiver (EZW-RT10) slot 
(63)
GS-AIR ID switch (67, 99)
HSPEAKER L jack (54)
ISPEAKER R jack (54)
JSURROUND SELECTOR switch (67, 
102)
Surround amplifier
PHONESPOWER
POWER/ON LINE
Front panelRear panel
RSURROUND SELECTOR
S-AIR ID
EZW-RT10
SPEAKER
SURROUND
PA I R I N GCB
A
SURROUND
BACK
L
 

13GB
Getting Started
BDV-IT1000
Getting Started
Unpacking
 Front speakers (2)
 Surround speakers (2)
 Center speaker (1)
 Subwoofer (1)
 Baffle covers (short 3, long 
2)
 Grilles (5) Floor bases (4)
 Poles (4)
 Long screws (8, black)
 Foot pads (thick 2, thin 2)
 Wall mounting brackets 
(top) (5)
 Wall mounting brackets 
(bottom) (5) Bracket covers (10)
 Screws (5)
 AM loop antenna (aerial) (1)
 FM wire antenna (aerial) (1)
 Speaker cords (6, white/red/
blue/gray/green/purple)

 Remote commander (remote)...

14GB
Getting Started
Note Unpack the speakers, being careful not to touch the speaker units.
 Keep speakers away from one another. Speakers are magnetically attracted, may hit each other, and cause damage.
 Keep magnetic objects such as watches, magnetic card, etc., away from the speakers.
 R6 (size AA) batteries (2)  Calibration mic (1)  Surround amplifier (1)
 Speaker cord cover (1)  Speaker cord holder (1)  Wireless transceivers for the 
unit (2)
 Operating Instructions
 Basic connections (card)...

15GB
Getting Started
BDV-IS1000
 Front speakers (2), center 
speaker (1), and surround 
speakers (2)
 Subwoofer (1)
 AM loop antenna (aerial) (1) FM wire antenna (aerial) (1)
 Video cord (1)
 Remote commander 
(remote) (1)
 R6 (size AA) batteries (2)
 Calibration mic (1)
 Brackets (5) Wrench (1)
 Surround amplifier (1)
 Speaker cord cover (1)
 Speaker cord holder (1)
 Wireless transceivers for the 
unit (2)
 Operating Instructions
 Basic connections (card)
or
 

16GB
Getting Started
Inserting batteries into the remote
Insert two R6 (size AA) batteries (supplied) by matching the 3 and # ends on the batteries to the 
markings inside the compartment.
Note Do not leave the remote in an extremely hot or humid place. 
 Do not use a new battery with an old one.
 Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
 If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible...

17GB
Getting Started
xSet-top box/digital satellite receiver/Sony component (such as VCR, DVD player/recorder, 
etc.) operation
Press STB (STB lights up for 1 second).
The remote enters set-top box/digital satellite receiver operation mode, and STB lights up when you 
press buttons for operation (STB does not light up when you press a button that is not available for the 
set-top box/digital satellite receiver). 
To operate the set-top box/digital satellite receiver/Sony Component, set the remote signal...

18GB
Getting Started
Step 1: Assembling the Speakers
(BDV-IT1000 only)
You can set speakers in two ways using stands: if you would like to place them on a floor, use speaker 
stands (page 23) and if on a desk, shelf, etc., use desktop stands (page 31).
Before connecting the speakers, assemble the speakers.
Caution on using the speakers
 When moving the speakers, keep one hand under the desktop stand and hold both sides of the speaker. 
When you use speaker stands with the speakers, hold the pole and the...

19GB
Getting Started
About how to connect the speaker cords, see page 54.
Note Spread a cloth on the floor to avoid damaging the floor when you assemble the speakers.
 When assembling, take care not to touch the speaker units.
Tip You can install the front, center, and surround speakers on a wall by using the wall mounting bracket (supplied) 
(page 42). In this case, you need to attach neither the speaker stand nor desktop stand to the speaker.
How to identify the speakers
Check the label on the...

20GB
Getting Started
1Remove the cover from the speaker.
Pry up the cover by inserting a thin, flat object into the slit in the cover. To replace the cover, see 
Step 3. The removed cover is used in a later step, so be careful not to lose it.
Note When assembling, take care not to touch the speaker unit.
2Connect the speaker cords to the speaker.
Use the speaker cords (green). Be sure to match the speaker cords to the appropriate terminals on 
the speakers: the speaker cord with the color tube to 3, and...