Snow Blower Stiga DUO LINE SNOW CUBE SNOW CRYSTAL 8218-2254-10 Instructions Manual

41
DEUTSCHDE
D. Zuerst den Stecker des Verlängerungskabels aus der 
Steckdose ziehen. Dann das Verlängerungskabel vom 
Motor trennen.
Anm.: Um eine Beschädigung des Elektrostarts zu 
verhindern, nutzen Sie ihn im folgenden Intervall: 5 s 
eingeschaltet – 5 s ausgeschaltet. Wenn der Motor nach 
zehn Versuchen noch nicht gestartet wurde, lassen Sie 
den Elektrostart mindestens 40 min abkühlen, bevor Sie 
ihn erneut verwenden. Kann der Motor auch weiterhin 
nicht gestartet werden, lassen Sie den Motor von...

42
DEUTSCHDE
2. Die Ölablassschraube herausdrehen.
3.  Das Öl in ein Gefäß fließen lassen.
4.  Die Ablassschraube wieder eindrehen.
5.  Neues Öl einfüllen. Angaben über die Ölsorte und die 
Menge finden Sie im Abschnitt “ 5.2”. 
6.3 ZÜNDKERZE
Die Zündkerze einmal pro Jahr oder alle 100 Betriebsstunden 
kontrollieren.
Wenn die Elektroden verbrannt sind, die Zündkerze reinigen 
oder austauschen. Der Motorhersteller empfiehlt: Briggs & 
Stratton LDF7TC oder gleichwertige.
Korrekter Elektrodenabstand:...

43
DEUTSCHDE
7.3 ALLGEMEINE INFORMATIONEN ZU 
KEILRIEMEN
Die Keilriemen sind einmal pro Saison zu kontrollieren und 
zu justieren sowie bei Bedarf zu ersetzen. Diese Arbeiten 
sind von einer autorisierten Servicewerkstatt auszuführen.
7.4 SEILZÜGE FÜR DIE BEDIENELEMENTE 
EINSTELLEN
Wenn die Riemen ausgetauscht wurden, ebenfalls die 
Seilzüge für die Bedienelemente justieren (siehe unten).
1.  Das Zündkabel von der Zündkerze abziehen.
2.  Drücken Sie den Hebel (1:O oder 1:N) herab. Der Hebel 
sollte einen...

44
ENGLISHEN
1 GENERAL
This symbol indicates CAUTION. Serious 
personal injury and/or damage to property may 
result if the instructions are not followed carefully.
1.1 SYMBOLS
The following symbols appear on the machine. They are 
there to remind you of the care and attention required in use. 
This is what the symbols mean:
Warning.
Read and understand the owner’s manual 
before using this machine.
Disconnect the spark plug wire, and 
consult technical literature before 
performing repairs or...

45
ENGLISHEN
• If the machine starts vibrating abnormally, stop the 
engine and look for the cause. Vibration is normally a 
sign of something wrong.
• Stop the engine and disconnect the spark plug cable: 
a. If the machine steers away from the driving position. 
b. If the auger housing or discharge chute is blocked and 
must be cleaned. 
c. Before beginning repairs or adjustments.
• Always make sure the rotating parts have stopped and all 
the controls are disengaged before cleaning, repairing or...

46
ENGLISHEN
In addition, the following Accessories/tools are supplied:
3.2 UNPACKING
1.  Remove all loose items from the carton.
2.  Cut the four corners of the carton and let the sides fall 
down.
3.  Roll the snow thrower from the carton.
3.3 HANDLE
The procedure requires two persons as the handle must be 
held in position during the assembly.
1.  Position the snow thrower on its auger.
2. Cube:
Assemble the gear panel. See fig. 3a.
Crystal:
Loosen both wheels from their axis and move them out 
about...

47
ENGLISHEN
4.5 START BUTTON – ELECTRICAL START (R) 
(CRYSTAL)
Activates the electric starting motor.
4.6 STOP SWITCH (S)
Used to stop the engine. The switch has two positions:
Pulled out-OFF – The engine stops, engine can not 
start.
Pushed in-ON – The engine can be started, engine 
running.
4.7 ELECTRIC CABLE – ELECTRICAL START (T) 
(CRYSTAL)
Supplies power to the starting motor. Connect the cable to a 
220/230 volt earthed socket via an earthed extension lead. It 
is wise to use an earth fault...

48
ENGLISHEN
5.3 FILL UP THE PETROL TANK
Always use lead-free petrol. Oil-mixed 2-stroke petrol must 
not be used.
NOTE! Bear in mind that ordinary lead-free petrol is 
perishable; do not purchase more petrol than can be used 
within thirty days.
Environmental petrol can be used, i.e. alkylate petrol. This 
type of petrol has a composition that is less harmful for 
people and nature.
Petrol is highly inflammable. Always store fuel in 
containers that are made especially for this 
purpose. 
Store the...

49
ENGLISHEN
5.  Adjust the shoes with the screws (1:H) to suit the ground 
conditions: 
- On flat ground, e.g. asphalt, the shoes should be about  
3mm under the scraping blade.
- On uneven ground, e.g. gravel paths, the shoes should 
be about  30mm under the scraping blade.
Always adjust the shoes so that gravel and stones 
are not fed into the snow thrower. There is a risk 
for personal injury if these are thrown out at high 
speed. 
Ensure the shoes are adjusted the same on both sides.
5. Adapt the...

50
ENGLISHEN
7.1 TROUBLE SHOOTING
7.2 ADJUSTING THE SCRAPER BLADE AND 
SHOES
The scraper blade (1:V) and shoes (1:H) gets worn after a 
long term of use.
Adjust the scraper blade (always together with the shoes) 
until desired distance to the ground.
The scraper blade and the shoes are reversible and can be 
used on both sides.
See ”“STARTING” på sidan 48”.
7.3 GENERAL ABOUT DRIVE BELTS
The drive belts should be checked and adjusted once per 
season and replaced when needed. This should all be done at...