Sharp Xv Z10000u Projector User Manual

Connections and Setup
-29
Screen Size and Projection Distance
When using a wide
screen (16:9)
In case of displaying the
16:9 picture on the whole
of the 16:9 screen.y
1 (Max.) = (0.05058x – 0.0447) × 3.28
y
2 (Min.) = (0.03734x – 0.0447) × 3.28
z
1 (Upper) = 0
z
2 (Lower) = –0.45x
Diag. (x)
300
250
200
150
133
106
100
92
84
72
60
40Width
261
218
174
131
116
92
87
80
73
63
52
35Height
147
123
98
74
65
52
49
45
41
35
29
20Maximum (y1)
541 (16.5 m)
451 (13.7 m)
36 (11.0 m)
2612 (8.2 m)
2311 (7.3 m)
1811...

-30
Projection from behind the screen

Place a translucent screen between the projector and the au-
dience.

Reverse the image by setting “Rear” for “PRJ Mode” in the
“Options” menu. See
page 69 for use of
this function.
Projection using a mirror

Place a mirror (normal flat type) in front of the lens.

Reverse the image by setting “Rear” for “PRJ Mode” in the
“Options” menu,
when the mirror is
placed on the audi-
ence side. See page
69 for use of this
function.
Info
•When using a mirror, be sure to...

Basic Operation
Basic Operation 

Image Projection
Basic Procedure
Connect the required external equipment to
the projector before operating the following
procedures.
Info
•The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page 
34.
1Plug the power cord into the
wall outlet.
•The power indicator illuminates red, and
the projector enters standby mode.
2Press  on the remote control
or 
 on the projector.
•The power indicator...

Basic Operation
-33
3Press , , ,  or 
on the remote control or  on
the projector to select the IN-
PUT mode.
•After pressing  once on the projector,
use 
 to select the desired input mode.
Note
•When no signal is received, “NO
SIGNAL” will be displayed. When a
signal that the projector is not pre-
set to receive is received, “NOT
REG.” will be displayed.
•The INPUT mode is not displayed
when “OSD display” is set to “Level
A” or “Level B”. (See page 64.)
About the INPUT modes
"On-screen Display...

Image Projection
Power (ON)
button
4Press  on the remote control
or 
 on the projector, then
press 
 or  again while the
confirmation message is dis-
played, to turn off the projec-
tor.
Note
•If you accidentally pressed  and
do not want to turn off the power,
wait until the confirmation message
disappears.
Info
•Do not unplug the power cord dur-
ing projection or cooling fan opera-
tion. This can cause damage due
to the rise in internal temperature,
as the cooling fan also stops.
•When connected to...

Basic Operation
-35
3Press ' or " to select the de-
sired language, and then press
.
4Press .
•The desired language will be set as
the on-screen display. 

*
Keystone Correction and Vertical Size Adjustment
Correcting Trapezoidal
Distortion and Adjust-
ing the Vertical Size of
the Picture
This function allows for Keystone (On-screen
Trapezoidal Distortion) Correction and the
adjustment of the vertical size of the picture.
Note
•When the image is projected either from
top or from bottom toward the screen at
an angle, the image becomes distorted
trapezoidally.
The function for correcting trapezoidal dis-
tortion is called Keystone Correction.
•The Keystone...

Basic Operation
-37
Ajuste de Tamanho VerticalA razão parente da tela poderá variar quando a função de 
deslocamento da lente é usada em combinação com a função 
Correção Trapezoidal. Neste caso, ajuste a razão aparente usando o 
ajuste de tamanho vertical. 
Tecla UNDO
Premindo ' aumenta o 
tamanho vertical da 
imagem.
Aperte        para 
reposicionar a imagem.
Premindo " diminui o 
tamanho vertical da 
imagem.
Aperte        para 
reposicionar a imagem.
3When adjusting vertical size,
pressing...

-38
Menu Bar Items
This list shows the items that can be set in the projector.
 INPUT 1 / 2 / 5 Mode
* In INPUT 5, the items in “Signal Type” are “D. PC RGB”, “D. PC Comp.”, “D. Video RGB”, “D. Video Comp.”
“A. RGB” and “A. Comp.”.
Note
•The resolution, vertical frequency and horizontal frequency figures displayed above are for example
purposes only.
•Picture adjustment settings differ depending on the type of input signal.
Signal Type
RGB
Component*
Standard
Black Detail
Brighten
Custom 1
Custom 2
SVM...