Sharp Xv Z10000u Projector User Manual

Easy to Use Functions
-69
Reversing/Inverting Projected Images
This projector is equipped with a reverse/invert image function that allows you to reverse or
invert the projected image for various applications.
Setting the Projection
Mode
Select “PRJ Mode” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 40 to 43.
Selected Item
Front
Ceiling + Front
Rear
Ceiling + Rear
Description
Normal image
Inverted image
Reversed image
Reversed and inverted image
Front Ceiling+Front...

This function can be used to display all the adjusted settings as a list on the screen.
Displaying the Adjustment Settings
Overview of All Menu
Settings
Select the “Status” menu on the menu
screen and press 
 .
➝For operating the menu screen, see
pages 40 to 43.
-70 

Appendix
Appendix 

-72
Cleaning the lens

Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the coat-
ing film on the surface of the lens.

As the surface of the lens can easily get dam-
aged, be sure not to scrape or hit the lens.
Cleaning the exhaust and intake vents

Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Maintenance
Cleaning the projector

Be sure to...

Appendix
-73
Cleaning the Ventilative Holes
Power
(OFF)
button
Power
(OFF)
button
Cleaner 
hose
Cleaner
hose
Ventilative
holes
Ventilative
holes
• This projector is equipped with
ventilative holes to ensure the opti-
mal operating condition of the projec-
tor.
• Periodically clean the ventilative hole
by vacuuming it off with a vacuum
cleaner.
• The ventilative holes should be
cleaned every 100 hours of use. Clean
the ventilative holes more often when
the projector is used in a dirty or
smoky location....

-74
Maintenance Indicators

The warning lights on the projector indicate problems inside the projector.

If a problem occurs, either the temperature warning indicator or the lamp replacement indicator will
illuminate red, and the power will turn off. After the power has been turned off, follow the proce-
dures given below.
About the temperature warning indicator
If the temperature inside the pro-
jector increases, due to blockage
of the air vents, or the setting lo-
cation, “
” will blink in the
lower...

Appendix
-75
Info
•If the temperature warning indicator illuminates, and the power turns off, follow the above possible solutions
and then wait until the projector has cooled down completely before plugging in the power cord and  turning
the power back on. (At least 5 minutes.)
•If the power is turned off and then turned on again, as during a brief test, the lamp replacement indicator may
be triggered, preventing the power from going on. Should this occur, take the power cord out of the wall outlet
and...

-76
Lamp

It is recommended that the lamp (sold separately) be replaced after approximately 1,900 cumulative
hours of use or when you notice a significant deterioration in the picture and color quality. The lamp
usage time can be checked with “Lamp Timer” in the “Options” menu on the menu screen.

For lamp replacement, please consult your nearest Authorized SharpVision Service Center or Dealer.

The actual lamp service life may be less than 2,000 hours depending on the environment in which
the projector...

Appendix
-77
Lamp
unitBQC-XVZ100001
Removing and Install-
ing the Lamp Unit
Info
•Be sure to remove the lamp unit by the
handle. Be sure not to touch the glass
surface of the lamp unit or the inside of
the projector.
•To avoid injury to yourself and damage
to the lamp, be sure to carefully follow
the steps below.
•Do not loosen other screws except for the
lamp unit cover and lamp unit.
(Only the silver screws are loosened).
•Please refer to the installation manual
included with the lamp unit.
1Press  on...

-78
User service screws
1
2
4Remove the lamp unit.
•Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of
the arrow.
5Insert the new lamp unit.
•Press the lamp unit firmly into the lamp
unit compartment. Fasten the secur-
ing screws.
6Attach the lamp unit cover.
•Close the lamp unit cover in the direc-
tion of the arrow (to the close mark)
on the side of the projector. Then
tighten the user service screws.
Info
•If the lamp unit and lamp cover are...