Sharp Xv Z10000u Projector User Manual

							Connections and Setup
-29
Screen Size and Projection Distance
When using a wide
screen (16:9)
In case of displaying the
16:9 picture on the whole
of the 16:9 screen.y
1 (Max.) = (0.05058x – 0.0447) × 3.28
y
2 (Min.) = (0.03734x – 0.0447) × 3.28
z
1 (Upper) = 0
z
2 (Lower) = –0.45x
Diag. (x)
300
250
200
150
133
106
100
92
84
72
60
40Width
261
218
174
131
116
92
87
80
73
63
52
35Height
147
123
98
74
65
52
49
45
41
35
29
20Maximum (y1)
541 (16.5 m)
451 (13.7 m)
36 (11.0 m)
2612 (8.2 m)
2311 (7.3 m)
1811 (5.8 m)
1711 (5.5 m)
165 (5.0 m)
15 (4.6 m)
1210 (3.9 m)
108 (3.3 m)
71 (2.2 m)Minimum (y2)
3911 (12.2 m)
333 (10.1 m)
267 (8.1 m)
1911 (6.1 m)
177 (5.4 m)
1311 (4.3 m)
132 (4.0 m)
121 (3.7 m)
111 (3.4 m)
96 (2.9 m)
710 (2.4 m)
52 (1.6 m)Upper (z1)
0 (0 cm)
0 (0 cm)
0 (0 cm)
0 (0 cm)
0 (0 cm)
0 (0 cm)
0 (0 cm)
0 (0 cm)
0 (0 cm)
0 (0 cm)
0 (0 cm)
0 (0 cm) Screen size (16:9) Projection distance (y)
Distance from the lens center to
the lower edge of the screen (z)
Lower (z2)
–123 (–374 cm)
–103 (–311 cm)
–82 (–249 cm)
–62 (–187 cm)
–55 (–166 cm)
–44 (–131 cm)
–41 (–125 cm)
–39 (–114 cm)
–35 (–105 cm)
–211 (–90 cm)
–25 (–75 cm)
–18 (–50 cm)
x : Screen size (diag.) (inches)
y : Projection distance (feet)
z : Distance from the lens center to the
lower edge of the screen (feet) When using a normal
screen (4:3)
In case of setting the
16:9 picture to the full
horizontal width of the
4:3 screen.
y1 (Max.) = (0.05510x – 0.04593) × 3.28
y
2 (Min.) = (0.04068x – 0.04369) × 3.28
z
1 (Upper) = 0
z
2 (Lower) = –0.4904x
Diag. (x)
250
200
150
100
84
72
60Width
200
160
120
80
67
58
48Height
150
120
90
60
50
43
36Maximum (y1)
414 (12.6 m)
33 (10.1 m)
249 (7.5 m)
165 (5.0 m)
139 (4.2 m)
1110 (3.6 m)
910 (3.0 m)Minimum (y2)
306 (9.3 m)
244 (7.4 m)
183 (5.6 m)
121 (3.7 m)
102 (3.1 m)
88 (2.6 m)
72 (2.2 m)Upper (z1)
0 (0 cm)
0 (0 cm)
0 (0 cm)
0 (0 cm)
0 (0 cm)
0 (0 cm)
0 (0 cm) Screen size (4:3)Projection distance (y)
Distance from the lens center to
the lower edge of the screen (z)
Lower (z2)
–126 (–286 cm)
–10 (–229 cm)
–76 (–171 cm)
–5 (–114 cm)
–42 (–96 cm)
–37 (–82 cm)
–3 (–69 cm)
x : Screen size (diag.) (inches)
y : Projection distance (feet)
z : Distance from the lens center to the
lower edge of the screen (feet)
zx
y
3 4
: Screen area
: Picture area
9 16
: Picture area
Note
•There is an error of ±3% in the formula above.
•Values with a minus (–) sign indicate the distance of the lens center below the
bottom of the screen.
Note
•There is an error of ± 3% in the formula above.
•Values with a minus (–) sign indicate the distance of the lens center below the
bottom of the screen. The formula for screen size and projection distance
The formula for screen size and projection distance 
						

							-30
Projection from behind the screen

Place a translucent screen between the projector and the au-
dience.

Reverse the image by setting “Rear” for “PRJ Mode” in the
“Options” menu. See
page 69 for use of
this function.
Projection using a mirror

Place a mirror (normal flat type) in front of the lens.

Reverse the image by setting “Rear” for “PRJ Mode” in the
“Options” menu,
when the mirror is
placed on the audi-
ence side. See page
69 for use of this
function.
Info
•When using a mirror, be sure to carefully position both the pro-
jector and the mirror so the light does not shine into the eyes of
the audience.
Ceiling-mount setup

It is recommended that you use the optional Sharp ceiling-mount
bracket for this installation.

Before mounting the projector, contact your nearest Authorized
SharpVision Service Center or Dealer to obtain the
recommended ceiling-mount bracket (sold separately). (AN-
CM250 ceiling-mount bracket, AN-EP101B extension tube for
AN-CM250.)

Be sure to adjust the position of the projector to match the
distance (z) from the lens center position (see page 29) to the
lower edge of the image,
when mounting the projec-
tor on the ceiling.

Invert the image by setting
“Ceiling + Front” for “PRJ
Mode” in the “Options”
menu. See page 69 for use
of this function.
When using the default setting.
On-screen Display
Projecting a Reversed/Inverted Image
The image is reversed.
When using the default setting.
On-screen Display
The image is reversed.
When using the default setting.
On-screen Display
Setup
The image is inverted. 
						

							Basic Operation
Basic Operation 
						

							Image Projection
Basic Procedure
Connect the required external equipment to
the projector before operating the following
procedures.
Info
•The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page 
34.
1Plug the power cord into the
wall outlet.
•The power indicator illuminates red, and
the projector enters standby mode.
2Press  on the remote control
or 
 on the projector.
•The power indicator illuminates blue.
After the lamp replacement indicator il-
luminates, the projector is ready to start
operation.
Note
•The lamp replacement indicator il-
luminates, indicating the status of the
lamp.
Blue: The lamp is ready.
Blue blinking: The lamp is
warming up.
Red:
The lamp should be replaced.•If the power is turned off and imme-
diately switched on again, the lamp
replacement indicator may take time
to illuminate.
•When controlling the projector using
RS-232C commands from a com-
puter, wait for at least 30 seconds
after the power has been turned on,
and then transmit the commands.
-32
INPUT
button
Power (ON)
button Power (OFF)
button MENU button
", ',\, | buttons
ENTER
button
Power (ON)
button
INPUT
buttons', ", \, |
buttons MENU button
ENTER
buttonPower (OFF)
button
Lamp replacement
indicator Power indicator 
						

							Basic Operation
-33
3Press , , ,  or 
on the remote control or  on
the projector to select the IN-
PUT mode.
•After pressing  once on the projector,
use 
 to select the desired input mode.
Note
•When no signal is received, “NO
SIGNAL” will be displayed. When a
signal that the projector is not pre-
set to receive is received, “NOT
REG.” will be displayed.
•The INPUT mode is not displayed
when “OSD display” is set to “Level
A” or “Level B”. (See page 64.)
About the INPUT modes
"On-screen Display (Example)
Using RGB*
Using
Component
INPUT 2 mode
Using
Component INPUT 1 mode
INPUT 3 mode
INPUT 4 modeUsing RGB*
➝
➝➝ ➝
INPUT 5 mode
➝
* Input the RGB signal of the DTV, not
the computer.Using S-Video
Using Video
Using Analog
RGB
The display varies accord-
ing to the “Signal Type” with
the INPUT 5.  The diagram
shown above is the ex-
ample of having selected
“Analog RGB”.
Used for projecting images
from equipment that sends
component signals or RGB
signals connected to the
INPUT 1 or 2 terminals.
Used for projecting im-
ages from equipment con-
nected to the S-VIDEO in-
put terminal.
Used for projecting im-
ages from equipment
connected to the VIDEO
input terminal.
Used for projecting im-
ages from equipment
connected to the DVI in-
put terminal. INPUT 1
INPUT 2
(Compo-
nent
/RGB*)
INPUT 3
(S-Video)
INPUT 4
(Video)
INPUT 5
(Digital PC
RGB/
Digital PC
Component/
Digital Video
RGB/Digital
Video
Component/
Analog RGB/
Analog
Component) 
						

							Image Projection
Power (ON)
button
4Press  on the remote control
or 
 on the projector, then
press 
 or  again while the
confirmation message is dis-
played, to turn off the projec-
tor.
Note
•If you accidentally pressed  and
do not want to turn off the power,
wait until the confirmation message
disappears.
Info
•Do not unplug the power cord dur-
ing projection or cooling fan opera-
tion. This can cause damage due
to the rise in internal temperature,
as the cooling fan also stops.
•When connected to equipment such
as an amplifier, be sure to turn off
the power to the equipment con-
nected first and then to the projec-
tor.
Selecting the On-screen
Display Language
•The on-screen display language of the
projector can be set to English, German,
Spanish, Dutch, French, Italian, Swedish,
Portuguese, Chinese, Korean or Japa-
nese.
1Press .
•The menu will be displayed.
2Press \ or | to select “Lan-
guage”.
MENU
button
', ", \, |
buttons
-34
Power (OFF)
button
ENTER button 
						

							Basic Operation
-35
3Press ' or " to select the de-
sired language, and then press
.
4Press .
•The desired language will be set as
the on-screen display. 
						

							*
Keystone Correction and Vertical Size Adjustment
Correcting Trapezoidal
Distortion and Adjust-
ing the Vertical Size of
the Picture
This function allows for Keystone (On-screen
Trapezoidal Distortion) Correction and the
adjustment of the vertical size of the picture.
Note
•When the image is projected either from
top or from bottom toward the screen at
an angle, the image becomes distorted
trapezoidally.
The function for correcting trapezoidal dis-
tortion is called Keystone Correction.
•The Keystone Correction can be adjusted
up to angle of approximately ±20 degrees.
•There are some input signal in which
“KEYSTONE” does not work.
1Press .
•Each time  is pressed, the settings
toggles as shown on the right.
2Press ', ", \ and | to adjust
the Keystone correction.
•If you want to make more detailed cor-
rections, press 
 to display the test
pattern, and then press 
' '' '
', 
" "" "
", 
\ \\ \
\ and
| || |
| to make the adjustments.
Note
•Since the trapezoidal distortion of the im-
age can be corrected up to an angle of
approximately ±20 degrees, the actual
screen can be diagonally set up to that
angle as well.
•Press  to cancel Keystone Correction.
•Straight lines or the edges of images
may appear jagged while adjusting
the image.
KEYSTONE button
UNDO buttonENTER button
Normal screenKeystone Correc-
tion screen
Compresses
upper side.
Compresses
lower side.
Test pattern', ", \, |
buttons
Vertical size
adjustment screen
*“V-SIZE” is not dis-
played when the value
of “KEYSTONE” is “0”.
-36 
						

							Basic Operation
-37
Ajuste de Tamanho VerticalA razão parente da tela poderá variar quando a função de 
deslocamento da lente é usada em combinação com a função 
Correção Trapezoidal. Neste caso, ajuste a razão aparente usando o 
ajuste de tamanho vertical. 
Tecla UNDO
Premindo ' aumenta o 
tamanho vertical da 
imagem.
Aperte        para 
reposicionar a imagem.
Premindo " diminui o 
tamanho vertical da 
imagem.
Aperte        para 
reposicionar a imagem.
3When adjusting vertical size,
pressing 
 again displays
the vertical size adjustment
menu.
4Press "and ' to adjust the
vertical size of the picture, and
press 
.
•See below for details about the verti-
cal size screen. 
						

							-38
Menu Bar Items
This list shows the items that can be set in the projector.
 INPUT 1 / 2 / 5 Mode
* In INPUT 5, the items in “Signal Type” are “D. PC RGB”, “D. PC Comp.”, “D. Video RGB”, “D. Video Comp.”
“A. RGB” and “A. Comp.”.
Note
•The resolution, vertical frequency and horizontal frequency figures displayed above are for example
purposes only.
•Picture adjustment settings differ depending on the type of input signal.
Signal Type
RGB
Component*
Standard
Black Detail
Brighten
Custom 1
Custom 2
SVM Gamma
Standard
Custom 1
Custom 2
Custom 3
+30 –30+30 –30
+30 –30
+30 –30+30 –30
11500 5500
Main menu Sub menuMain menu Sub menu
Contrast
Bright
Color
Tint
Sharp
Picture Setting
CLR Temp
Reset
White Emphasis [ON/OFF] Gamma Position
Color Selected
Progressive Mode
2D Progressive
3D Progressive
Film Mode Picture
Page 44
+30 –30+30 –30
Custom 3 Custom 1
+30 –30
Color Selected
Target 
Lightness
Chroma
Hue
Reset (This Color)
Reset (All Colors)
View Settings
R-Gamma G-Gamma
B-Gamma
R-Gain
G-GainB-Gain
R-OffsetG-OffsetB-OffsetReset
[R] Red
[Y] Yellow
[G] Green
[C] Cyan
[B] Blue
[M] Magenta C.M.S.
Page 50
Gamma PositionStandard
Black Detail
Brighten
Custom 1
Custom 2
SVM Gamma GammaPage 48
Standard
Memory 5 Memory 1INPUT1 / 2 / 5 Memory
+150 –150
+150 –150+60 –60
+60 –60
1
2•
•7
1
2
•
•7
1
2
3
4
•
•7Resolution
1024 × 864
1152 × 864
1152 × 870
1152 × 882 Resolution
1024 × 768
  800 × 600Vert Freq
60 Hz
75 Hz
Resolution
1024 × 768
 800 × 600Vert Freq
60 Hz
75 Hz
1024 × 768
48.4 KHz
60 Hz Fine Sync
Page 53Clock
Phase
H-Pos
V-Pos
Reset
Save Setting
Select Setting
Special Modes
Signal Info
Auto Sync
Auto Sync Disp [ON/OFF]
Resolution
Hor Freq
Vert Freq
OFF
Normal
High Speed
Options
Page 62
Reset
Lamp Timer
DNR
OSD Display
Background
Economy Mode
Power Save [ON/OFF]
RS-232C Port [ON/OFF]
Auto Power Off [ON/OFF]
OFF
Level 1
Normal
Level A
Level B
Blue
None
PRJ Mode
Subtitle
Front
Ceiling + Front
Rear
Ceiling + Rear RS-232C
9600 bps
38400 bps
115200 bpsLevel 3
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português Language
Page 34
Status
Page 70
Digi. Shift+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30