Sharp Ux300 Plain Paper Fax Machine Operation Manual

VOLUME keys
Press these keys to adjust the volume of the handset when the handset
is lifted, the volume of the speaker when the SPEAKER key has been
pressed, or the volume of the ringer at all other times.
FUNCTION key
Press this key to select various special functions.
Panel release
Grasp this finger hold and pull toward you to open the operation panel.
Number keys
Use these keys to dial numbers, and enter numbers and letters during
number/name storing procedures.
HOLD/SEARCH key
Press this key to...

UX300U-ISCODD
Connections
Points to keep in mind when setting up
Do not place the machine in
direct sunlight.Do not place the machine near
heaters or air conditioners.
Keep dust away from the
machine.Keep the area around the
machine clear.
About condensation
If the machine is moved from a cold to a warm place, it is possible that
condensation may form on the scanning glass, preventing proper
scanning of documents for transmission. To remove the condensation,
turn on the power and wait approximately two...

Handset
Connect the handset as shown and place it on the handset rest.
¨The ends of the handset cord are identical, so they will go into
either jack.
Make sure the
handset cord goes
into the jack marked
with a handset
symbol on the side
of the machine!
Use the handset to
make ordinary phone
calls, or to transmit
and receive
documents manually.
1. Installation 
Connections
11 

Power cord
Plug the power cord into a 120 V, 60 Hz, grounded (3-prong) AC
outlet.
Caution!
Do not plug the power cord into any other kind of outlet. This will
damage the machine and is not covered under the warranty.
The machine does not
have a power on/off switch,
so the power is turned on
and off by simply plugging
in or unplugging the power
cord.
Note:
If your area experiences a high incidence of lightning or power
surges, we recommend that you install surge protectors for the power and
telephone...

Telephone line cord
Insert one end of the line cord into the jack on the back of the machine
marked TEL. LINE. Insert the other end into a standard (RJ11C)
single-line wall telephone jack.
Be sure to insert the
telephone line cord into
the 
TEL. LINE jack.
Do not insert it into the
TEL. SET jack!
Comments:
·
·· ·Your fax is set for touch-tone dialing. If you are on a pulse dial (rotary) line,
you must set the fax for pulse dialing by changing Option Setting 8. This
procedure is described in Chapter 8,...

Trays
Attach the paper tray extension.
¨Pull the paper release plate forward. Insert the paper tray
extension horizontally into the notches in the paper tray. Rotate
the paper tray extension up until it snaps into place.
Attach the original document support.
Note: The original
document support
has a top side and a
bottom side. If you
cannot insert the tabs
on the support into
the holes, turn the
support over.
Connections
14 

Extension phone (optional)
If desired, you can connect an extension phone to the TEL. SET jack
on the fax.
¨To connect an answering machine to your fax, see Chapter 6,
Answering Machine Hookup.
1Remove the seal covering the TEL.
SET jack.
2Connect the extension phone line to
the TEL. SET jack.
TEL.
SETTEL.
LINE
1. Installation 
Connections
15 

UX300U-ISIF

Loading the Imaging Film
Your fax uses a roll of imaging film to create printed text and images.
The print head in the fax applies heat to the imaging film to transfer
ink to the paper. Follow the steps below to load or replace the film.
The initial starter roll
of imaging film
included with your fax
can print about 30
letter-size pages.When replacing the
film, use a roll of Sharp
UX-3CR imaging film.
One roll can print about
100 letter-size pages.
Note:If there is paper in the paper tray,...

If you are installing the imaging film for the first
time, go to Step 6.
3Remove the imaging film cartridge from the print compartment
(grasp the handle at the front of the cartridge) and turn it over.
4Remove the used film from the cartridge.
5Remove the four green gears from the used film.
DO NOT DISCARD THE FOUR GREEN GEARS!
1. Installation 
Loading the Imaging Film
17 

6Remove the new roll of imaging film from its packaging.
·
·· ·Do not yet remove the band that holds the rolls together.
7Insert the large gear into the green end of the empty spool. Make
sure the two protrusions on the large gear fit firmly into the slots in
the end of the spool.
Insert the remaining three gears into the spools, making sure the
protrusion on each gear fits firmly into one of the slots in the end of
each spool.
·
·· ·If needed, pull the spools apart slightly to allow the gears to fit...