Sharp Projector Pg M20s User Manual

Basic Operation
Basic Operation 

Image Projection
Basic Procedure
Connect the required external equipment to 
the projector before operating the following 
procedures.
The language preset at the factory is English. 
If you want to change the on-screen display 
to another language, reset the language ac-
cording to the procedure on page 30.
1Plug the power cord into the
wall outlet.
• The POWER indicator illuminates up 
in red, and the projector enters 
standby mode.
2Press  on the projector or
on the remote control.
• The POWER...

Basic Operation
-29
"On-screen Display (Example)➝
➝➝
Using Analog
RGB
Using
Component
INPUT 2 Mode
   Using S-Video
INPUT 3 Mode
   Using Video
3Press ,  or  on the re-
mote control to select the IN-
PUT Mode.
•After pressing  once, use the but-
ton to select the desired INPUT Mode.
Note
•When no signal is received, “NO
SIGNAL” will be displayed. When a
signal that the projector is not pre-
set to receive is received, “NOT
REG.” will be displayed.
About the INPUT Modes
INPUT 1 Mode
Using
   DVI...

Image Projection (cont.)
POWER
button
5Press  to temporarily turn off
the picture and sound.
Note
•Pressing  again will turn the pic-
ture and the sound back on.
6Press , then press  again
while the confirmation message
is displayed, to turn off the pro-
jector.
Note
•If you accidentally pressed  and
do not want to turn off the power,
wait until the confirmation message
disappears.
Info
•Do not unplug the power cord dur-
ing projection or cooling fan opera-
tion. This can cause damage due
to the rise in...

Basic Operation
-31
Zoom
 in
Zoom out
3Press  or  to select the
desired language, and then
press 
.
4Press .
•The desired language will be set as
the on-screen display.
Adjusting the Lens
The image is focused and adjusted to the
desired size using the focus ring or zoom
knob on the projector.
1The focus is adjusted by rotat-
ing the focus ring.
2Zooming is adjusted  by mov-
ing the zoom knob.
Zoom knob
Focus ring 

Correcting Trapezoidal Disto rtion ( Keystone Correction )
Correcting Trapezoidal 
Distortion
This function allows for Keystone (On-screen 
Trapezoidal Distortion) Correction.
Note
•Keystone Correction is the correction for 
trapezoidal distortion that occurs when 
the image is positioned away from the
center axis of the screen.
• The trapezoidal distortion can be corrected
up to an angle of approximately  ±35 de-
grees.
1Press .
• Pressing  again while the BOR-
DER, STRETCH or SMART STRETCH 
screen is...

Basic Operation
-33
•The Digital Shift function works with BORDER, STRETCH or SMART STRETCH s\
creen. For details,  
see page  47.
Digital Shift SettingFor easier viewing, this function shifts the entire image projected on  
the screen up or down when projecting 16:9 images from DVD 
players and DTV* decoders.
* DTV is the umbrella term used to describe the new digital television 
system in the United States.
UNDO button
Press         to move the 
projected image upwards. 
Press         to reset the...

-34
Menu Bar Items
This list shows the items that can be set in the projector. 
 INPUT 1 Mode
Page  66
Note
•The resolution, vertical frequency and horizontal frequency figures disp\
layed above are for example 
purposes only.
• When DVI digital signals have been entered into INPUT 1, in  “Picture ” only  “CLR Temp ”,  “Red ” and  “Blue ”
can be adjusted and in  “Fine Sync ” only  “Signal Info ”,  “Auto Sync ” and  “Auto Sync Disp ” can be used.
• When the signal type is set as  “Component ”, in the...

Basic Operation
-35
 INPUT 2 / 3 Mode
+30
– 30
+30
– 30
+30
– 30
+30
– 30
+30
– 30
+30
– 30
+30
– 30
+3
– 3
English 
Deutsch
Espa ñol
Nederlands
Fran çais
Italiano
Svenska
Portugu ês
Picture 
Options (1)
Contrast 
Bright 
Color 
Tint 
Sharp 
Red 
Blue 
CLR Temp 
Reset 
Progressive Mode
Power Save [ON/OFF] 
Auto Search [ON/OFF] 
DNR 
OSD Display 
Video System 
Background 
Startup Image
Auto Power Off [ON/OFF]
2D Progressive 
3D Progressive
Film Mode
OFF
Level 1 
 Level 3
Normal 
Level A
Level B 
Auto...

This projector has two sets of menu screens that allow you to adjust the image and various
projector settings.
You can operate the menus from the projector or remote control using the following proce-
dure.
Using the Menu Screen
On-screen menu for INPUT 1 RGB modeOn-screen menu for INPUT 2
or INPUT 3 Mode
Menu Bar
(Main Menu)
MENU button
 buttons
ENTER button
MENU button
 buttons
ENTER button
" "" "
"On-screen Display
Basic Operations
(Adjustments)
1Press .
Note
•The “Picture” menu...