Sharp Projector Pg M20s User Manual

Introduction
-7 18. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an...

-8
IMPORTANT SAFEGUARDS (cont.)
Be sure to read the following safeguards when setting up 
your projector.
Caution concerning the lamp unit

Potential hazard of glass particles if 
lamp ruptures. In case of lamp rup-
ture, contact your nearest Sharp Au- 
thorized Projector Dealer or Service 
Center for a replacement. 
See  “Replacing the Lamp ” on page  7 1.
Cautions concerning the setup of the projector

 For minimal servicing and to maintain high image qual- 
ity, SHARP recommends that this projector be...

Introduction
-9
PDF operation manuals in several languages are included in the CD-ROM. To utilize these
manuals, you need to install Adobe Acrobat Reader on your PC (Windows or Macintosh). If
you have not installed Acrobat Reader yet, you can download it from the Internet (http://
www.adobe.com) or install it from the CD-ROM.
To install Acrobat Reader from the CD-ROM
For Windows:
1Insert the CD-ROM in the CD-ROM drive.
2Double click on the “My Computer” icon.
3Double click on the “CD-ROM” drive.
4Double...

-10
Projector (Front and Top View)
Part Names
Foot releases/Adjustment
feet
For adjusting the projector’s
height.
Attaching the terminal cover
Attach the terminal cover by
placing it on the side panel of the
projector and pressing it into
place, as shown in the illustration.
TEMPERATURE
WARNING indicator
When the internal
temperature rises, this
indicator will illuminate
red.
Zoom knobFocus ring AV MUTE button
For temporarily turning off the
sound and picture.
ENTER buttonFor setting items selected
or...

Introduction
-11
2420
69
11
26
21
21
24
Projector (Side View)
Exhaust ventAC socket
Kensington Security
Standard connector
Using the Kensington Lock
•
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructions on how to use it to secure the
projector.
Attaching the lens cap
After putting the lens cap strap on the
lens cap, pass the other end of the strap
through the hole under the...

-12
Remote Control
Part Names (cont.)
28
49
48
30
29
29
29
29
44
32
36
46
36
50
36
33
26FORWARD/BACK button
Moves forward or backwards
when connected to a computer
using a USB cable. Same as the
[Page Down] and [Page Up]
keys on a computer keyboard.
AV MUTE buttonFor temporarily turning off the
sound and picture.
VOLUME buttons
For adjusting the speaker
sound level.
INPUT 2 button
For switching the input mode to
INPUT 2.
INPUT 1 buttonFor switching the input mode to
INPUT 1.
AUTO SYNC buttonFor...

Introduction
-13
23 (7 m)30°
30°45°
Using the Remote Control

The remote control can be used to control the projector
within the ranges shown in the illustration.
Note
•The signal from the remote control can be reflected off a screen
for easy operation. However, the effective distance of the signal
may differ due to the screen material.
When using the remote control:
•Be sure not to drop, expose to moisture or high temperature.
•The remote control may malfunction under a fluorescent lamp.
Under that...

-14
Note
Accessories
Remote control
RRMCGA013WJSA
Two R-03 batteries
(“AAA” size, UM/SUM-4, HP-16 or similar)
Power cord (6 (1.8m))
For U.S., Canada, etc.
QACCDA007WJPZFor Europe, except U.K.
QACCV4002CEZZFor U.K., Hong Kong
and Singapore
QACCBA012WJPZFor Australia, New
Zealand and Oceania
QACCL3022CEZZ
•Depending on the region, projectors only ship with one power cord (see above). Use the power cord that
corresponds to the wall outlet in your country.
DVI to 15-pin D-sub
cable (6 (1.8m))...

Setup and Connections
Setup and Connections 

Up DownFoot releases
Adjustment feet
Setup
Using the Adjustment
Feet
The height of the projector can be adjusted
using the adjustment feet when the surface
of the projector is placed on is uneven or when
the screen is slanted.
The projection of the image can be made
higher by adjusting the projector when it is in
a location lower than the screen.
1Press the foot releases.
2Lift the projector to adjust its
height and remove your hands
from the foot releases.
3Rotate the adjustment feet to
make minor...