Sharp Projector Pg M20s User Manual

							DIGITAL MULTIMEDIA
PROJECTOROPERATION MANUAL
MODEL
PG-M20S
Introduction
Setup and Connections
Basic Operation
Easy to Use Functions
Appendix 
						

							This equipment complies with the requirements of Directives 89/336/EEC a\
nd 73/23/EEC as amended by 93/68/ 
EEC. 
Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/ 
68/EWG. 
Ce matériel répond aux exigences contenues dans les directives 89/\
336/CEE et 73/23/CEE modifiées par la 
directive 93/68/CEE. 
Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23\
/EEG, gewijzigd door 93/68/EEG.
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.
Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/\
EEC e 73/23/EEC, come emendata dalla 
direttiva 93/68/EEC. 
Η εγκατ\bσταση αυτ\f αν\νταπκρίνεται στις α\νπαιτ\fσεις των δηγιώ\νν της Ευρωπαϊκ\fς Ενω\νσης 89/336/ 
ΕΚ και 73/23/ΕΚ, #π\νως ι καννισµί αυτ\νί συµπληρώθηκαν απ# την \νδηγία 93/68/ΕΚ. 
Este equipamento obedece às exigências das directivas 89/336/CEE e\
 73/23/CEE, na sua versão corrigida 
pela directiva 93/68/CEE. 
Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/\
23/CEE, modificadas por medio de la 
93/68/CEE. 
Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/\
23/EEC så som kompletteras av 93/68/ 
EEC. 
Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23\
/EEC i endringen 93/68/EEC.
Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC v\
aatimukset, joita on muutettu direktiivillä 93/68/EEC.
IMPORTANT
For your assistance in reporting the loss or theft of your 
Projector, please record the Serial Number located on 
the bottom of the projector and retain this information.
Before recycling the packaging, please be sure that 
you have checked the contents of the carton thoroughly 
against the list of “Supplied accessories” on page 1 4.Model No.: PG-M20S 
Serial No.: 
						

							SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should
the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked 
 or  and of the same rating as
above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse.  Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the
mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of
in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 10A socket outlet, as a serious
electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
•The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
•The wire which is coloured brown must be connected to the plug terminal which  is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
•If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
•The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN. 
						

							The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian,
Dutch, Portuguese, Chinese (Traditional Chinese and Simplified Chinese), Korean and Arabic. Carefully read
through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Schwedisch, Spanisch,
Italienisch, Niederländisch, Portugiesisch, Chinese (Traditionelles Chinesisch und einfaches Chinesisch), Koreanisch
und Arabisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, suédois,
espagnol, italien, néerlandais, portugais, chinois (chinois traditionnel et chinois simplifié), coréen et arabe.
Veuillez lire attentivement ces instructions avant de faire fonctionner le projecteur.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, svenska, spanska,
italienska, holländska, portugisiska, kinesiska (traditionell kinesiska och förenklad kinesiska), koreanska och
arabiska. Läs noga igenom bruksanvisningen innan projektorn tas i bruk.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, sueco, español,
italiano, holandés, portugués, chino (chino tradicional y chino simplificado), coreano y árabe. Lea
cuidadosamente las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, svedese, spagnolo, italiano,
olandese, portoghese, cinese (cinese tradizionale e cinese semplificato), coreano e arabo. Leggere
attentamente le istruzioni per l’uso prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds, Spaans, Italiaans,
Nederlands, Portugees, Chinees (Traditioneel Chinees en Vereenvoudigd Chinees), Koreaans en Arabisch.
Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Sueco, Espanhol, Italiano,
Holandês, Português, Chinês, Chinês (Tradicional e Chinês Simplificado), Coreano e Árabe. Leia
cuidadosamente todas as instruções de operação antes de operar o projetor. 
						

							Introduction
-1
Before using the projector, please read this operation manual carefully.
There are two important reasons for prompt warranty registration of your new SHARP Projector, using
the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE
READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
WARNING:High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING:To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
WARNING:FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equip-
ment.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
IntroductionENGLISH
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREWS.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to correct the interference
at his own expense.
See bottom of actual set.
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device
complies with FCC Class A verification.
WARNING:This is a Class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
U.S.A. ONLY
U.S.A. ONLY
U.S.A. ONLY
U.S.A. ONLY 
						

							-2
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. During 
normal operation, when turning the power off always use the POWER button on the projector or on the remote
control. Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.
FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
Caution Concerning the Lamp Replacement
See  “Replacing the Lamp ” on page  7 1.
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of 
these materials may be regulated due to environmental considerations. For disposal or recycling information,
please contact your local authorities or, if you are located in the United States of America, the Electronic Industries
Alliance: www.eiae.org .
PRECAUTIONS A OBSERVER LORS  
DU REMPLACEMENT DE LA LAMPE.
DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS. 
L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE 1 HEURE
AVANT DE PROCEDER AU REMPLACEMENT DE LA LAMPE.
NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPE BQC-PGM20X//1.
RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.
ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN.
LAMPE A MOYENNE PRESSION : RISQUE D’EXPLOSION. DANGER POTENTIEL
DE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE
A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI. 
  
BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD. 
HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP.
REPLACE WITH SAME SHARP LAMP UNIT TYPE BQC-PGM20X//1 ONLY.
UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING.
MEDIUM PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS
PARTICLES IF LAMP HAS RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL.
LAMP REPLACEMENT CAUTION 
						

							Introduction
-3
Outstanding Features
1. Image Quality
•Superior image quality with Fujinon™ optical lens system
• Newly developed DDR (Double Data Rate) chip eliminates Color Break- 
ing phenomena common with previous generation DLP™ projectors.
• Newly developed 12
° DMD™ chip provides significantly improved opti-
cal efficiency and excellent contrast ratio.
2. Light, Compact, and Unique Slim Design
• A new optical engine creates a unique slim design and compact size
(4.2 liters, 5.8 lbs. (2.6 kg)).
3. Superior PC Compatibility
•Supports a refresh rate (vertical frequency) of up to 160 Hz and a wide
range of synchronous signals.
•   Using  Advanced Intelli gent Compression  T e chnolog y, computer screens
of SXGA+ (1,400  #1,050) resolution can be displayed with minimal dis-
tortion.
4. Advanced Computer & Video lntegrated Composer Technology
• Realizes vivid images using the latest high image quality circuitry.
•New I/P conversion algorithm enhances the performance of the motion detect I/P 
conversion.
Extensive improvements on the jagged edges or slanted lines in moving images.
•Contrast Control Dynamic Gamma
Improved contrast and natural color gradation by minimizing hue change.
•Color Management Function
Supports sRGB (color management).
•Noise Reduction
Allows for a clear image even with noisy source signals.
•New Edge Up-Scaling
Reduces jaggies and flickering when up-scaling edges of slanted lines, enabling sharper quality 
images. 
						

							-4
Contents
Adjusting the Picture ........................................  40
Adjusting Image P refe rences  ................................. .40
Selecting the Signal  Type  .......................................  40
P rog ressive Mod e................................................... .41
Adjusting Computer Images  ............................  42
When Auto Sync is OF F.......................................... .42
Saving Adjustment Setting s.................................... .42
Selecting Adjustment Settings  ............................... .43
Special Mode settings  ............................................ .43
Checking the Input Signal  ...................................... .43
Auto Sync Adjustment  ............................................ .44
Auto Sync Display Function  ...................................  44
Easy to Use Functions
Selecting the Picture Displ ay Mode  ................  46
Displaying a Still Image  ....................................  48
Enlarging a Specific Portion of an Image  .......  49
Gamma Correction Functio n............................  50
Displaying Dual Pictures (Pict in Pict)  ............  51
Selecting the Power Save Mode  ......................  52
Setting the Power Save Mode  ................................ .52
Automatic Power Shuto ff Functio n..........................  52
Acti vating the sRGB Color Man ag ement
Function  .......................................................  53
A uto Sea rc h Function  .......................................  53
Video Digital Noise Reduction (DNR) System  .. .54
Setting the On-screen Display  .........................  54
Setting the  Video System  .................................  55
Saving Projected Image s..................................  56
Capturing the Image  ..............................................  56
Deleting the Captu red Image  ................................. .56
Setting a Background Imag e............................  57
Selecting a Startup Image  ................................  57
Using an RGB Monitor Loop-out Adaptor  ......  58
Displ aying the Lamp Usage  Time  ....................  58
Displ aying the Break  Timer  ..............................  59
Reversing/Inverting Projected Images  ............  60
Locking the Operation Buttons on the Projector  ............................  60
Setting up the Keylock  ........................................... .60
Canceling the Keylock Setting  ............................... .61
Setting up a Passwor d......................................  61
Entering the Passwo rd ............................................ .61
Changing the Passwo rd  .........................................  62
If  You Forget  Your Passwo rd ...................................  62
Introduction
Outstanding Features  .........................................  3
Contents ............................................................... 4 
IMPO RTANT SAFEG UARDS  ...............................  6
H ow to Access the PDF Operation Ma nual s.....  9
Part Names  ........................................................  10
P rojector (F ront and  Top  View)  ............................... .10
P rojector (Side  View)  ..............................................  11
Remote Cont rol  .......................................................  12
Using the Remote Control  ................................  13
A vailable Range of the Remote Cont rol  .................  13
Inse rting the Batteries  ............................................ .13
Accessories  .......................................................  14
Setup and Connections
Setup  ..................................................................  16
Using the Adjustment Feet  .....................................  16
Setting up the Sc reen  ............................................. .17
Sc reen Size and P rojection Distance  ..................... .18
P rojecting a Reversed/Inve rted Image  ...................  19
Connecting the Projector to Other Device s....  20
Befo re Connectin g..................................................  20
This p rojector can be connected to:  ...................... .20
Connecting the Power Co rd  ...................................  20
Connecting the Projector to a Computer  ..........  21
Connecting to  Video Equipment  .......................  23
Connecting to a Monitor  ...................................  25
Using the Wireless Presentation Function of the Remote Control  ................................  26
Basic Operation
Setting with the Buttons
Image Projection  ...............................................  28
Basic P rocedu re  ..................................................... .28
Selecting the On-sc reen Display Language  .......... .30
Adjusting the Lens  ..................................................  31
Correcting  Trapezoidal Disto rtion
(Keystone Correction ).................................  32
Setting with the Menus
Menu Bar Items  .................................................  34
Using the Menu Screen  ....................................  36
Basic Operations (Adjustments)  ............................  36
Basic Operations (Settings ).................................... .38 
						

							Introduction
-5
Setting the Anti-Thef
t........................................  63
Entering the Keycode  ............................................. .63
Changing the Keycode  .......................................... .64
Initializing the Settings  .....................................  65
Displ aying the Adjustment Setting s................  66
Appendix
Carrying the Projector  ......................................  68
Maintenance  ......................................................  69
Maintenance Indicators  ....................................  70
Regarding the Lamp  .........................................  71
Lamp  ......................................................................  71
Caution Conce rning the Lamp  ............................... .71
Replacing the Lamp  ............................................... .71
Removing and Installing the Lamp Unit  .................  72
Resetting the Lamp Timer  ...................................... .73
Connecting Pin Assignments  ..........................  74
Computer Compatibility Chart  .........................  75
T roubleshooting  ................................................  76
For SHARP Assistance  .....................................  78
Specification s....................................................  79
Dimensions  ........................................................  80
Glossary  .............................................................  81
Index  ...................................................................  82 
						

							-61. Read Instructions
All the safety and operating instructions should be read
before the product is operated.
2. Retain InstructionsThe safety and operating instructions should be
retained for future reference.
3. Heed WarningsAll warnings on the product and in the operating
instructions should be adhered to.
4. Follow InstructionsAll operating and use instructions should be followed.
5. CleaningUnplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
6. AttachmentsDo not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and MoistureDo not use this product near water–for example, near
a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.
8. AccessoriesDo not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage
to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer,
or sold with the product. Any mounting of the product
should follow the manufacturer’s instructions, and
should use a mounting accessory recommended by
the manufacturer.
9. TransportationA product and cart combination
should be moved with care. Quick
stops, excessive force, and
uneven surfaces may cause the
product and cart combination to
overturn.
10.VentilationSlots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product
and to protect it from overheating, and these openings
must not be blocked or covered. The openings should
never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a book-
case or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
IMPORTANT SAFEGUARDS
11. Power SourcesThis product should be operated only from the type of
power source indicated on the marking label. If you
are not sure of the type of power supply to your home,
consult your product dealer or local power company.
For products intended to operate from battery power,
or other sources, refer to the operating instructions.
12. Grounding or PolarizationThis product is provided with one of the following types
of plugs. If the plug should fail to fit into the power outlet,
please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.
13. Power-Cord ProtectionPower-supply cords should be routed so that they are
not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point
where they exit from the product.
14. LightningFor added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent damage
to the product due to lightning and power-line surges.
15. OverloadingDo not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of
fire or electric shock.
16. Object and Liquid EntryNever push objects of any kind into this product through
openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the product.
17. ServicingDo not attempt to service this product yourself as
opening or removing covers may expose you to dan-
gerous voltage or other hazards. Refer all servicing to
qualified service personnel.
CAUTION: Please read all of these instructions before you operate this product and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to
assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR
FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic
rules for its installation, use and servicing.