Sharp Mxm264n User Guide

2-103
COPIER
Contents
CREATING A LARGE POSTER (Multi-Page 
Enlargement)
This function is used to enlarge an image of an original and print it as a composite image using multiple sheets of paper.
1
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Image Edit] key.
(4) Touch the [Multi-Page Enlargement] key.

[Image Edit] KEY (page 2-100)
Original 
(A4 (8-1/2 x 11) size)
Copy (enlarged image on 8 
sheets of A3 (11 x 17) paper) 

2-104
COPIER
Contents
2
* The size that is twice A0 size.
Set the enlargement size and the original 
size.
(1) Select the size system that you wish to use 
for multi-page enlargement.
Touch the   keys to display the screen that shows 
the desired group of sizes.
 1st screen: A system
 2nd screen: B system
 3rd screen: Inch system
(2) Select the enlargement size.
(3) Select the size of the original to be used.
A suitable original placement orientation (A) and the 
number of sheets of paper required for...

2-105
COPIER
Contents
4
Touch the [OK] key.
You will return to the special modes screen. Touch the [OK] key 
to return to the base screen of copy mode.
5
Press the [START] key.
Copying will begin.
If you have selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and 
then touch the [Read-End] key.
To cancel scanning and copying...
Press the [STOP] key ( ).
 The original must be placed on the document glass.
 Overlap of sections of image
- There will be...

2-106
COPIER
Contents
REVERSING THE IMAGE (Mirror Image)
This feature is used to make a copy that is a mirror image of the original.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Image Edit] key.

[Image Edit] KEY (page 2-100)
3
Select Mirror Image.
(1) Touch the [Mirror Image] key so that it is 
highlighted....

2-107
COPIER
Contents
COPYING IN THE CENTRE OF THE PAPER (Centring)
This is used to centre the copied image on the paper.
This lets you place the image in the centre of the paper when the original size is smaller than the paper size or when the 
image is reduced.
Not using the centring functionUsing the centring function
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch...

2-108
COPIER
Contents
REVERSING WHITE AND BLACK IN A COPY (B/W Reverse)
This is used to reverse black and white in a copy to create a negative image. This function can only be used for black 
and white copying.
Originals with large black areas (which use a large amount of toner) can be copied using Black/White Reverse to reduce 
toner consumption.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the...

2-109
COPIER
Contents
ADJUSTING THE SHARPNESS OF AN IMAGE (Sharpness)
This is used to sharpen an image or make it softer.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Sharpness] key.
3
Adjust the image.
(1) Touch the [Soft] key or the [Sharp] key.
(2) Touch the [OK] key.
You will return to the special modes...

2-110
COPIER
Contents
CHECKING COPIES BEFORE PRINTING 
(Proof Copy)
This function requires the hard disk drive.
This feature prints only one set of copies, regardless of how many sets have been specified. After the first set is checked 
for errors, the remaining sets can be printed. Previously it was necessary to re-scan the original each time changes to 
settings were required. However, this feature makes it possible to change settings for the scanned original without 
scanning it again, allowing you...

2-111
COPIER
Contents
4
Set the number of copies (number of 
sets) with the numeric keys.
If you will copy multiple originals using the document glass, 
switch to sort mode after this step.

Sort mode (page 2-32)
Up to 999 copies (sets) can be set.
If an incorrect number of copies is set...
Press the [CLEAR] key ( ) and then enter the correct number.
5
Press the [START] key.
One set of copies is printed.
If you are using the document glass to copy multiple originals, change originals and press the...

2-112
COPIER
Contents
7
Change the settings.
(1) Touch the key of the setting that you want 
to change.
The setting screen of the touched key opens. Change the 
settings and touch the [OK] key.
(2) Touch the [OK] key.
 To change the number of sets printed, set the desired number of copies (sets) with the numeric keys. After changing 
the number of sets, touch the [End] key in the touch panel (not the [START] key) to print the sets.
 Special modes that can be adjusted are Margin Shift, Pamphlet Copy,...