Sharp Mx2310u User Guide

4-57
FACSIMILE
Contents
CHECKING THE IMAGE TO BE TRANSMITTED 
(Preview)
This function requires the hard disk drive.
If you touch the [Preview] key before scanning the original, you can check the scanned image in the touch panel before 
sending the image.
* The factory default setting is disabled.
Depending on the size of the transmission data, part of the preview image may not appear in the preview screen in the touch 
panel.
1
Place the original.
Place the original face up in the document feeder tray,...

4-58
FACSIMILE
Contents
PREVIEW CHECK SCREEN
This section explains the preview check screen.
(1) Preview image
A preview of the scanned original appears.
If the image is cut off, use the scroll bars at the right and 
bottom of the screen to scroll the image. Touch a bar and 
slide it to scroll. (You can also touch the   keys to 
scroll.)
(2) Change page keys
When there are multiple pages, use these keys to 
change pages.
  keys:  Go to the first or the last page.
  keys:  Go to the previous page or the...

4-59
FACSIMILE
Contents
This section explains the basic procedures for receiving faxes.
RECEIVING FAXES
When the reception mode is set to Auto Reception, the machine will receive and print faxes automatically. The fax 
reception mode is displayed in the base screen.
FAX RECEPTION
 When fax reception is in progress, it is possible to reserve a transmission by performing the transmission in memory 
transmission mode.
☞TRANSMISSION METHODS (page 4-26)
 To print received faxes, make sure that the required...

4-60
FACSIMILE
Contents
RECEIVING A FAX
When a fax is transmitted to the machine, the machine automatically receives and prints the fax.
1
The machine rings and fax reception 
begins automatically.
A beep sounds when reception ends.
System Settings (Administrator): Speaker Settings
This is used to change the volume and tone of the reception beep.
System Settings (Administrator): Number of Calls in Auto Reception
This is used to change the number of rings on which fax reception begins automatically. To...

4-61
FACSIMILE
Contents
RECEIVING A FAX MANUALLY
A fax can be received manually using the touch panel. While the machine rings, touch the [Speaker] key in the base 
screen and then touch the [Fax Manual Reception] key that appears.
 When a call is answered by touching the [Speaker] key, you will be able to hear the other party, however, you will not be 
able to speak.
 Even when you use an extension phone to answer a call, you can touch the [Fax Manual Reception] key in the touch panel 
to begin fax...

4-62
FACSIMILE
Contents
PRINTING A PASSWORD-PROTECTED FAX 
(Hold Setting For Received Data Print)
Hold Setting for Received Data Print can be enabled in the system settings (administrator) to have faxes received to 
memory without being printed. To print the faxes, a password must be entered. When this function is used, a password 
entry screen appears in the touch panel when a fax is received.
When the previously programmed 4-digit password is entered with the numeric keys, printing begins.
The [Cancel]...

4-63
FACSIMILE
Contents
CHECKING THE IMAGE BEFORE PRINTING
This function requires the hard disk drive.
When Received Data Image Check Setting is enabled* in the system settings (administrator), you can check a 
received image in the touch panel before printing it out. When this function is enabled, follow the steps below to print a 
received image.
* The factory default setting is disabled.
Depending on the size of the received data, part of the image in the image check screen on the touch panel may not...

4-64
FACSIMILE
Contents
CHECKING THE IMAGE BEFORE 
FORWARDING
This function requires the hard disk drive.
When Received Data Image Check Setting is enabledin the system settings (administrator), you can select the 
received data from the list and forward it to the addresses recorded in the address book. When this function is enabled, 
follow the steps below to forward the received image.
* The factory default setting is disabled.
Depending on the size of the received data, part of the image in the image...

4-65
FACSIMILE
Contents
4
Start forward
Touch the [Start forward.] key.
If the screen of step 1 appears when you are configuring settings in the setting screens of any of the modes, the configured 
settings will be cancelled if you view the image. After viewing the image, you will return to the base screen of image send 
mode, regardless of which mode you were in previously.
System Settings (Administrator): Received Data Image Check Setting
Use this to specify whether or not a received Internet fax can...

4-66
FACSIMILE
Contents
IMAGE CHECK SCREEN
This function requires the hard disk drive.
This section explains the image check screen.
(1) Information display
This shows information on the displayed image.
(2) Preview image
An image of the selected received image appears.
If the image is cut off, use the scroll bars at the right and 
bottom of the screen to scroll the image. Touch a bar and 
slide it to scroll. (You can also touch the   keys to 
scroll.)
(3) Change page keys
When there are multiple pages,...