Sharp Mx2310u User Guide

2-122
COPIER
Contents
ADJUSTING THE COLOUR (Colour Balance)
The colour, tone, and density of colour copies can be adjusted.
Each of the colours yellow, cyan, magenta, and black 
are divided into 8 gradations from light to dark, and the 
average density of each gradation can be adjusted,
or all eight gradations can be adjusted at once.
OK
OKCancel
Colour Adjustments
Colour Balance
Y
M
C
Bk
12345678All
12345678
Dark Light
C Cyan+M Magenta+
Y Yellow+B Black+
1
Place the original.
Place the original face up...

2-123
COPIER
Contents
3
Examples of colour balance adjustment
Adjust the colour balance.
(1) Select the colour to be adjusted.
Select [Y] (yellow), [M] (magenta), [C] (cyan), or [Bk] (black).
If only the rectangular area around the letter in a key is 
highlighted, the settings have been changed from the 
factory default settings.
(2) Select the gradation to be adjusted.
Select the gradation with the   keys.
Touch the   keys to move the highlighting to one of 
gradations 1 to 8 or All.
To adjust all eight...

2-124
COPIER
Contents
ADJUSTING THE BRIGHTNESS OF A COPY (Brightness)
The brightness of colour images can be adjusted.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Colour Adjustments] key.
(4) Touch the [Brightness] key.
☞[Colour Adjustments] KEY (page 2-117)
3
Adjust the brightness.
(1) Adjust the...

2-125
COPIER
Contents
ADJUSTING THE INTENSITY OF A COPY (Intensity)
This is used to adjust the intensity (saturation) of colour images.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Colour Adjustments] key.
(4) Touch the [Intensity] key.
☞[Colour Adjustments] KEY (page 2-117)
3
Adjust the intensity.
(1) Adjust...

2-126
COPIER
Contents
CHECKING COPIES BEFORE PRINTING 
(Proof Copy)
This function requires the hard disk drive.
This feature prints only one set of copies, regardless of how many sets have been specified. After the first set is checked 
for errors, the remaining sets can be printed. Previously it was necessary to re-scan the original each time changes to 
settings were required. However, this feature makes it possible to change settings for the scanned original without 
scanning it again, allowing you...

2-127
COPIER
Contents
4
Set the number of copies (number of 
sets) with the numeric keys.
If you will copy multiple originals using the document glass, 
switch to sort mode after this step.
☞Sort mode (page 2-35)
Up to 999 copies (sets) can be set.
If an incorrect number of copies is set...
Press the [CLEAR] key ( ) and then enter the correct number.
5
Press the [COLOUR START] key or the [BLACK & WHITE START] key.
One set of copies is printed.
If you are using the document glass to copy multiple...

2-128
COPIER
Contents
7
Change the settings.
(1) Touch the key of the setting that you want 
to change.
The setting screen of the touched key opens. Change the 
settings and touch the [OK] key.
(2) Touch the [OK] key.
 To change the number of sets printed, set the desired number of copies (sets) with the numeric keys. After changing 
the number of sets, touch the [End] key in the touch panel (not the [START] key) to print the sets.
 Special modes that can be adjusted are Margin Shift, Pamphlet Copy,...

2-129
COPIER
Contents
CHECKING THE NUMBER OF SCANNED 
ORIGINAL SHEETS BEFORE COPYING 
(Original Count)
The number of scanned original sheets can be counted and displayed before copying is executed. By allowing you to check 
the number of original sheets that were scanned, this helps reduce the occurrence of copy mistakes.
1
Insert the originals face up in the 
document feeder tray.
Insert the originals all the way into the document feeder tray. 
Multiple originals can be placed in the document feeder...

2-130
COPIER
Contents
4
After scanning is finished, check the 
number of sheets that were scanned and 
touch the [OK] key.
Copying will begin.
 When job build mode is used, the number of scanned sheets 
appears when the [Read-End] key is touched.
 The number that is displayed is the number of scanned 
original sheets, not the number of scanned original pages. 
For example, when two-sided copying is performed using 
one original, the number 1 will appear to indicate that one 
original sheet was scanned,...

2-131
COPIER
Contents
COPYING ORIGINALS OF DIFFERENT SIZES 
(Mixed Size Original)
This function requires the automatic document feeder.
Even when B4 (8-1/2 x 14) originals are mixed in with A3 (11 x 17) originals, all originals can be copied at once. When 
scanning the originals, the machine automatically detects the size of each original and uses paper appropriate for that size.
When mixed size original is combined with auto ratio selection, the ratio is adjusted individually for each original according...