Sharp Mx2310u User Guide

2-52
COPIER
Contents
5
Touch the [OK] key.
You will return to the base screen of copy mode.
6
Press the [COLOUR START] key or the [BLACK & WHITE START] key.
Copying will begin.
If you are using the document glass, change originals and press the [START] key. Repeat until all pages have been scanned 
and then touch the [Read-End] key. (For the second original and following originals, use the same [START] key as you did for 
the first original.)
To cancel scanning of the original and copying...
Press the...

2-53
COPIER
Contents
COPYING A LARGE NUMBER OF 
ORIGINALS AT ONCE (Job Build)
This function requires the automatic document feeder to be installed.
When copying a very large number of originals, this function allows you to divide the originals into sets and feed each 
set through the automatic document feeder one set at a time.
Use this function when you wish to copy all of the originals as a single job but the number of originals exceeds the 
maximum number that can be inserted.
This function is...

2-54
COPIER
Contents
3
Press the [COLOUR START] key or the [BLACK & WHITE START] key to scan the 
first set of originals.
Scanning begins.
To cancel scanning...
Press the [STOP] key ( ).
4
Insert the next set of originals and press the [COLOUR START] key or the 
[BLACK & WHITE START] key.
Repeat this step until all originals have been scanned.
The copy settings (Exposure, Paper Select, and Copy Ratio only) can be changed for each set of originals. If you need 
to change the copy setting, follow the steps...

2-55
COPIER
Contents Changing the copy settings for each set of originals
The copy settings (Exposure, Paper Select, and Copy Ratio only) can be changed for each set of originals.
Perform the step below before pressing the [Start] key to scan the originals in step 4 above.
1
Touch the [Change] key.
2
Change the desired copy settings in the 
screen that appears and press the [Start] 
key.
Scanning of the originals will begin using the changed copy 
settings.
To cancel the copy setting changes and begin...

2-56
COPIER
Contents
USING TWO MACHINES TO MAKE A LARGE 
NUMBER OF COPIES (Tandem Copy)
This function requires the hard disk drive.
This function requires the hard disk expansion kit to be installed.
Two machines connected to the same network can be used to run a large copy job in parallel.
Each machine prints half of the copies, reducing the time required to complete the job.
Master machine and slave machine
In the following explanation, the master machine is the machine that is used to scan the...

2-57
COPIER
Contents
3
Set the number of copies (number of 
sets) with the numeric keys.
Up to 999 copies (sets) can be set. When the [COLOUR 
START] key or the [BLACK & WHITE START] key is pressed, 
the copies will automatically be divided between the master 
and slave machines.
If an odd number of copies is set, the master machine will print 
the extra set.
If an incorrect number of copies is set...
Press the [CLEAR] key ( ) and then enter the correct number.
4
Press the [COLOUR START] key or the...

2-58
COPIER
Contents
In this situation...
If a machine runs out of paper
If either the master machine or the slave machine run out of paper, the machine that ran out of paper will hold the job while 
the machine that still has paper continues the job. When paper is added to the machine that ran out, the job resumes.
When user authentication is enabled
User authentication is enabled in the master machine: tandem copying is possible.
User authentication is enabled in the slave machine but not in the master...

2-59
COPIER
Contents
USING A DIFFERENT PAPER TYPE FOR 
COVERS (Covers/Inserts)
This function requires the automatic document feeder.
A different type of paper can be inserted in positions corresponding to front and back covers of a copy job when the 
automatic document feeder is used. A different type of paper can also be automatically added as an insert at specified 
pages.
Example of adding covers
Example of adding covers/insertsExample of adding inserts
About the explanations of covers and 
inserts...

2-60
COPIER
Contents
INSERTING COVERS IN COPIES (Cover Settings)
This function requires the automatic document feeder.
A different type of paper can be inserted at the positions corresponding to the front and back covers of a copy job.
This is useful for arranging documents in an attractive format and for using a different type of paper as a cover on an 
estimate sheet or similar document.
Covers can be used in combination with inserts.
Copying on a front cover and inserting together with a back cover
1...

2-61
COPIER
Contents
4
Select cover settings.
(1) If the cover sheet will be copied on, touch 
the [Yes] key. Otherwise, touch the [No] 
key.
If the [No] key is touched, only cover insertion will be 
performed.
In this case, go to step (3).
(2) To copy on one side of the cover, touch the 
[1-Sided] key. To copy on both sides of the 
cover, touch the [2-Sided] key.
(3) Select paper settings for the cover.
(A) The currently selected paper tray for the cover is 
displayed.
(B) The size and type of paper in...